Nissan Leaf. Manual - part 1166

 

  Index      Nissan     Nissan Leaf (2011-2014 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1164  1165  1166  1167   ..

 

 

Nissan Leaf. Manual - part 1166

 

 

TM-70

< DTC/CIRCUIT DIAGNOSIS >

[ELECTRIC SHIFT]

P0705 TRANSMISSION RANGE SENSOR A

5. Check the continuity VCM vehicle side harness connector terminal and ground.

Is the inspection result normal?

YES

>> Replace the electric shift sensor. Refer to 

TM-121, "Exploded View"

.

NO

>> Repair or replace damaged parts.

Electric shift sensor

VCM

Electric shift sensor

Continuity

Connector

terminal

Connector

terminal

1

E61

17

M57

11

Existed

3

16

10

5

3

9

2

E62

84

5

4

85

3

6

86

4

Electric shift sensor

VCM

Ground

Continuity

Connector

terminal

1

E61

17

Ground

Not existed

3

16

5

3

2

E62

84

4

85

6

86

P0706 TRANSMISSION RANGE SENSOR A

TM-71

< DTC/CIRCUIT DIAGNOSIS >

[ELECTRIC SHIFT]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P0706 TRANSMISSION RANGE SENSOR A

DTC Logic

INFOID:0000000010119577

DTC DETECTION LOGIC

Position Pattern Table

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, power switch OFF and wait for at least

10 seconds, then perform the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1. Set the vehicle to READY.

2. Select “Data Monitor” in “SHIFT”.

3. Select “RANGE POSITION”.

4. Shift the selector lever as follows. (Hold the selector lever at each position for 2 seconds or more.) 

-

→ N → R → N → D → N → H

5. Repeat step 4 five more times.

6. Check DTC.
Is “P0706” detected? 

YES

>> Go to 

TM-71, "Diagnosis Procedure"

.

NO-1 >> To check malfunction symptom before repair: Refer to 

GI-53, "Intermittent Incident"

.

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010119578

1.

CHECK ELECTRIC SHIFT SENSOR INPUT SIGNAL

With CONSULT

1. Set the vehicle to READY.

2. Select “Data Monitor” in “SHIFT”.

3. Select “SHIFT SENSOR 1”, “SHIFT SENSOR 2”, “SHIFT SENSOR 3”, “SHIFT SENSOR 4”, “SHIFT SEN-

SOR 5”, and “SHIFT SENSOR 6”.

4. Operate the selector lever to identify a electric shift sensor of which value does not change.

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

Possible cause

P0706

TRANSMISSION RANGE SENSOR A
(Transmission range sensor “A” Circuit 
Range/Performance)

Two or more sensors out of electric 
shift sensors No. 1 to No. 6 are stuck 
at ON or OFF.

• Electric shift sensor
• Harness or connectors

(Each circuit is open or shorted.)

Electric shift control module 

recognition position

Selector lever position

Electric shift sensor

No.  1

No.  2

No.  3

No.  4

No.  5

No.  6

H

H

OFF

OFF

ON

OFF

OFF

ON

P

H

OFF

OFF

ON

OFF

OFF

ON

R

R

ON

ON

OFF

OFF

OFF

OFF

N

N

OFF

ON

ON

ON

OFF

OFF

D

D

OFF

OFF

OFF

ON

ON

OFF

Monitor item

Condition

Value / Status

SHIFT SENSOR 1

Selector lever is held in R position

ON

Other than the above

OFF

TM-72

< DTC/CIRCUIT DIAGNOSIS >

[ELECTRIC SHIFT]

P0706 TRANSMISSION RANGE SENSOR A

Without CONSULT

1. Set the vehicle to READY.

2. Operate the selector lever.

3. Check the voltage between VCM vehicle side harness connector terminal and ground.

>> GO TO 2.

2.

CHECK HARNESS BETWEEN VCM AND ELECTRIC SHIFT SENSOR

1. Power switch OFF.

2. Disconnect the VCM connector.

3. Disconnect the electric shift sensor connector.

4. Check the continuity between the malfunctioning electric shift sensor identified at Step 1 and the harness

connector terminal located on the vehicle side of the VCM.

SHIFT SENSOR 2

Selector lever is held in R and N positions

ON

Other than the above

OFF

SHIFT SENSOR 3

Selector lever is held in H (Home) and N positions

ON

Other than the above

OFF

SHIFT SENSOR 4

Selector lever is held in N and D positions

ON

Other than the above

OFF

SHIFT SENSOR 5

Selector lever is held in D position

ON

Other than the above

OFF

SHIFT SENSOR 6

Selector lever in H (Home) position

ON

Other than the above

OFF

Monitor item

Condition

Value / Status

Electric 

shift sen-

sor

VCM

Ground

Condition

Voltage

(Approx.)

Connector

terminal

1

E61

17

Ground

Selector lever is held in R position

0 V

Other than the above

5 V

3

16

Selector lever is held in H (Home) and N posi-
tions

0 V

Other than the above

5 V

5

3

Selector lever is held in D position

0 V

Other than the above

5 V

2

E62

84

Selector lever is held in R and N positions

0 V

Other than the above

5 V

4

85

Selector lever is held in N and D position

0 V

Other than the above

5 V

6

86

Selector lever in H (Home) position

0 V

Other than the above

5 V

P0706 TRANSMISSION RANGE SENSOR A

TM-73

< DTC/CIRCUIT DIAGNOSIS >

[ELECTRIC SHIFT]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

5. Check the continuity VCM vehicle side harness connector terminal and ground.

Is the inspection result normal?

YES

>> Replace the electric shift sensor. Refer to 

TM-121, "Exploded View"

.

NO

>> Repair or replace damaged parts.

Electric shift sensor

VCM

Electric shift sensor

Continuity

Connector

terminal

Connector

terminal

1

E61

17

M57

11

Existed

3

16

10

5

3

9

2

E62

84

5

4

85

3

6

86

4

Electric shift sensor

VCM

Ground

Continuity

Connector

terminal

1

E61

17

Ground

Not existed

3

16

5

3

2

E62

84

4

85

6

86

 

 

 

 

 

 

 

Content   ..  1164  1165  1166  1167   ..