Nissan Frontier D22. Manual - part 909

 

  Index      Nissan     Nissan Frontier D22 Pickup (1998-2004 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  907  908  909  910   ..

 

 

Nissan Frontier D22. Manual - part 909

 

 

PRECAUTIONS

SRS-3

C

D

E

F

G

I

J

K

L

M

A

B

SRS

PRECAUTIONS

PFP:00001

Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT 
BELT PRE-TENSIONER”

EHS000SO

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system may include seat belt switch inputs and dual stage front air bag modules. If
equipped with dual stage front air bag modules, the SRS system uses the seat belt switches to determine the
front air bag deployment, and may only deploy one front air bag, depending on the severity of a collision and
whether the front occupants are belted or unbelted. Information necessary to service the system safely is
included in the SRS and SB section of this Service Manual.

The vehicle may be equipped with a passenger air bag deactivation switch. Because no rear seat exists where
a rear-facing child restraint can be placed, the switch is designed to turn off the passenger air bag so that a
rear-facing child restraint can be used in the front passenger seat. The switch is located in the center of the
instrument panel, near the ashtray. When the switch is turned to the ON position, the passenger air bag is
enabled and could inflate for certain types of collision. When the switch is turned to the OFF position, the pas-
senger air bag is disabled and will not inflate. A passenger air bag OFF indicator on the instrument panel lights
up when the passenger air bag is switched OFF. The driver air bag always remains enabled and is not affected
by the passenger air bag deactivation switch.

WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.

The vehicle may be equipped with a passenger air bag deactivation switch which can be operated
by the customer. When the passenger air bag is switched OFF, the passenger air bag is disabled
and will not inflate. When the passenger air bag is switched ON, the passenger air bag is enabled
and could inflate for certain types of collision. After SRS maintenance or repair, make sure the
passenger air bag deactivation switch is in the same position (ON or OFF) as when the vehicle
arrived for service.

Precautions for SRS “Air Bag” and “Seat Belt Pre-tensioner” Service

EHS000SP

Do not use a circuit tester to check SRS circuits unless instructed to in this Service Manual.

Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 min-
utes.
For approximately 3 minutes after the cables are removed, it is still possible for the air bags and seat belt
pre-tensioners to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes
have passed.

Air bag diagnosis sensor unit must always be installed with forward mark “

⇐” pointing toward the front of

the vehicle for proper operation. Also check air bag diagnosis sensor unit for deformities, dents, cracks
and rust before installation and replace as required.

The spiral cable must be aligned in the neutral position since its rotations are limited. Do not rotate steer-
ing column while steering gear is removed to avoid damaging spiral cable.

Handle air bag module carefully. Always place it with the pad side facing upward.

Conduct Self-diagnosis to check entire SRS for proper function after replacing any components. Refer to

SRS-20, "SRS Operation Check"

 .

After air bag inflates, the instrument panel assembly should be replaced if damaged.

SRS-4

PRECAUTIONS

Wiring Diagrams and Trouble Diagnosis

EHS000SQ

When you read wiring diagrams, refer to the following:

GI-13, "How to Read Wiring Diagrams"

PG-9, "POWER SUPPLY ROUTING"

 for power distribution circuit

When you perform trouble diagnosis, refer to the following:

GI-9, "HOW TO FOLLOW TEST GROUPS IN TROUBLE DIAGNOSES"

GI-25, "How to Perform Efficient Diagnosis for an Electrical Incident"

PREPARATION

SRS-5

C

D

E

F

G

I

J

K

L

M

A

B

SRS

PREPARATION

PFP:00002

Special Service Tools

EHS000SR

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

*: Special tool or commercial equivalent

Tool number
(Kent-Moore No.)
Tool name

Description

KV991072S0
(J38381-KIT)
Air bag deployment kit
KV99106400
(J38381)
Deployment tool

Disposing of air bag module and seat belt pre-
tensioner

J38381-80
Deployment tool adapter

For driver air bag module (4-door models) and 
seat belt pre-tensioner

KV99109000
(J44230)
Deployment tool adapter

For driver air bag module (2-door models)

(J38381-65)
Deployment tool adapter for front  pas-
senger air bag module

Connection between the deployment tool and 
front passenger air bag module (4-door mod-
els)

KV991065S0
(J38381-30)
Deployment tool adapters

 For passenger air bag module (2-door mod-
els)

KV99105300
(J41246)
Air bag module bracket

Anchoring air bag module

(J42057)
Air bag master key set

Removing and installing accessory air bag 
locking bolts

S-NT357

WHIA0089E

LRS138

SHIA0173E

LHIA0010E

S-NT354

LRS210

 

 

 

 

 

 

 

Content   ..  907  908  909  910   ..