Nissan Frontier D22. Manual - part 306

 

  Index      Nissan     Nissan Frontier D22 Pickup (1998-2004 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  304  305  306  307   ..

 

 

Nissan Frontier D22. Manual - part 306

 

 

DTC P0444, P0445 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID 

VALVE

EC-327

[KA24DE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

On Board Diagnosis Logic

UBS00D7I

DTC Confirmation Procedure

UBS00D7J

NOTE:
If “DTC Confirmation Procedure” has been previously conducted, always turn ignition switch OFF and wait at
least 5 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm battery voltage is more than 11V at idle.

 WITH CONSULT-II

1.

Turn ignition switch ON.

2.

Select “DATA MONITOR” mode with CONSULT-II.

3.

Start engine and let it idle for at least 30 seconds.

4.

If 1st trip DTC is detected, go to 

EC-330, "Diagnostic Procedure"

.

 WITH GST

Follow the procedure “WITH CONSULT-II”.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P0444

EVAP canister purge volume 
control solenoid valve circuit 
open

An excessively low voltage signal is sent 
to ECM through the valve

Harness or connectors
(The sensor circuit is open or shorted.)

EVAP canister purge volume control 
solenoid valve

P0445

EVAP canister purge volume 
control solenoid valve circuit 
shorted

An excessively high voltage signal is sent 
to ECM through the valve

Harness or connectors
(The sensor circuit is shorted.)

EVAP canister purge volume control 
solenoid valve

SEF058Y

EC-328

[KA24DE]

DTC P0444, P0445 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID 

VALVE

Wiring Diagram

UBS00D7K

BBWA1061E

DTC P0444, P0445 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID 

VALVE

EC-329

[KA24DE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

Specification data are reference values and are measured between each terminal and ground.

CAUTION:

Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.

:Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)

TER-

MINA

L NO.

WIRE 

COLOR

ITEM

CONDITION

DATA (DC Voltage)

4

LG/R

ECM relay
(Self-shutoff)

[Engine is running]
[Ignition switch: OFF]

For a few seconds after turning ignition switch 
OFF

0 - 1V

[Ignition switch: OFF]

A few seconds passed after turning ignition 
switch OFF

BATTERY VOLTAGE
(11 - 14V)

5

R/Y

EVAP canister purge 
volume control sole-
noid valve

[Engine is running]

Idle speed

BATTERY VOLTAGE

(11 - 14V)

[Engine is running]

Engine speed is 2,000 rpm (More than 200 sec-
onds after starting engine)

BATTERY VOLTAGE

(11 - 14V)

67

B/P

Power supply for 
ECM

[Ignition switch: ON]

BATTERY VOLTAGE
(11 - 14V)

72

B/P

117

B/P

Current return

[Engine is running]

Idle speed

BATTERY VOLTAGE
(11 - 14V)

SEF109V

SEF110V

EC-330

[KA24DE]

DTC P0444, P0445 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID 

VALVE

Diagnostic Procedure

UBS00D7L

1. 

CHECK POWER SUPPLY

1.

Turn ignition switch OFF.

2.

Disconnect EVAP canister purge volume control solenoid valve
harness connector.

3.

Turn ignition switch ON.

4.

Check voltage between EVAP canister purge volume control
solenoid valve terminal 2 and ground with CONSULT-II or tester.

OK or NG

OK

>> GO TO 3.

NG >> GO 

TO 

2.

2. 

DETECT MALFUNCTIONING PART

Check the following.

Harness for open or short between EVAP canister purge volume control solenoid valve and ECM relay

Harness for open or short between EVAP canister purge volume control solenoid valve and ECM

>> Repair harness or connectors.

3. 

CHECK OUTPUT SIGNAL CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect ECM harness connector.

3.

Check harness continuity between ECM terminal 5 and EVAP canister purge volume control solenoid
valve terminal 1.
Refer to Wiring Diagram.
Continuity should exist.

4.

Also, check harness for short to ground and short to power.

OK or NG

OK (With CONSULT-II)>>GO TO 5.
OK (Without CONSULT-II)>>GO TO 6.
NG

>> GO TO 4.

4. 

DETECT MALFUNCTIONING PART

Check the harness for open or short between EVAP canister purge volume control solenoid valve and ECM.

>> Repair open circuit or short to ground or short to power in harness or connectors.

SEF339V

Voltage

: Battery voltage

SEF192V

 

 

 

 

 

 

 

Content   ..  304  305  306  307   ..