Nissan Frontier D22. Manual - part 152

 

  Index      Nissan     Nissan Frontier D22 Pickup (1998-2004 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  150  151  152  153   ..

 

 

Nissan Frontier D22. Manual - part 152

 

 

VEHICLE SECURITY (THEFT WARNING) SYSTEM

BL-45

C

D

E

F

G

H

J

K

L

M

A

B

BL

System Description

EIS002CI

DESCRIPTION
1. Operation Flow

2. Setting the Vehicle Security System

Initial condition

1.

Close all doors.

2.

Close hood.

Disarmed phase
The vehicle security system is in the disarmed phase when any door(s) or hood is opened. The security indi-
cator lamp blinks every second.
Pre-armed phase and armed phase
The vehicle security system turns into the “pre-armed” phase when hood and all doors are closed and the
doors are locked by key or keyfob. (The security indicator lamp illuminates.)
After about 30 seconds, the system automatically shifts into the “armed” phase (the system is set). (The secu-
rity indicator lamp blinks every 2.6 seconds.)

3. Canceling the Set Vehicle Security System

When the doors are unlocked with the key or keyfob, the armed phase is canceled.

4. Activating the Alarm Operation of the Vehicle Security System

Make sure the system is in the armed phase. (The security indicator lamp blinks every 2.6 seconds.)
When either of the following operations 1) or 2) is performed, the horn and  headlamps operate intermittently
for about 50 seconds. (At the same time, the system disconnects the starting system circuit.)

1.

Engine hood or any door is opened before unlocking door with key or keyfob.

2.

Door is opened without first using key or keyfob.

POWER SUPPLY AND GROUND

Power is supplied at all times

through 7.5A fuse [No. 28, located in the fuse block (J/B)]

to smart entrance control unit terminal 49

to key switch terminal 1 and

to security indicator lamp terminal 1.

With the ignition switch in the ACC or ON position, power is supplied

through 7.5A fuse [No. 20, located in the fuse block (J/B)]

to smart entrance control unit terminal 26.

With the ignition switch in the ON or START position, power is supplied

through 10A fuse [No. 5, located in the fuse block (J/B)]

AEL579C

BL-46

VEHICLE SECURITY (THEFT WARNING) SYSTEM

to smart entrance control unit terminal 27.

Ground is supplied

to smart entrance control unit terminals 43 and 64

through body grounds M14 and M68.

INITIAL CONDITION TO ACTIVATE THE SYSTEM

To activate the vehicle security system, the smart entrance control unit must receive signals indicating the
doors and hood are closed and the doors are locked.
When a door is open, smart entrance control unit terminal 1, 2, or 3 (Crew Cab) receives a ground signal from
the corresponding door switch.
When the hood is open, ground is supplied

to smart entrance control unit terminal 6

through hood switch terminal +

through hood switch terminal –

through body grounds E12 and E54.

When the doors are locked with key or keyfob and none of the described conditions exist, the vehicle security
system will automatically shift to armed phase.

VEHICLE SECURITY SYSTEM ACTIVATION (WITH KEY OR KEYFOB USED TO LOCK DOORS)

If the key is used to lock doors, ground is supplied to smart entrance control unit terminal 11

through front door key cylinder switch LH terminal 1

through front door key cylinder switch LH terminal 2

through body grounds M14 and M68.

If this signal or lock signal from keyfob is received by the smart entrance control unit, the vehicle security sys-
tem will activate automatically.
Once the vehicle security system has been activated, smart entrance control unit terminal 38 supplies ground
to security indicator lamp terminal 2.
The security lamp will illuminate for approximately 30 seconds and then blink.
The vehicle security system is now in armed phase.

VEHICLE SECURITY SYSTEM ALARM OPERATION

The vehicle security system is triggered by

opening a door

opening the hood.

Once the vehicle security system is in armed phase, if the smart entrance control unit receives a ground signal
at terminal 1, 2, or 3 (Crew Cab) or 6 (hood switch), the vehicle security system will be triggered. The horn and
headlamps operate intermittently and the starting system is interrupted.
With the ignition switch in the ON or START position, power is supplied

through 10A fuse [No. 5, located in the fuse block (J/B)].

to vehicle security relay terminal 2.

If the vehicle security system is triggered, ground is supplied

to vehicle security relay terminal 1

through smart entrance control unit terminal 40.

With power and ground supplied, starter motor circuit is interrupted. The starter motor will not crank and the
engine will not start.
Power is supplied at all times

through 15A fuse (No. 32, located in fuse and fusible link box)

to horn relay terminal 3.

When the vehicle security system is triggered, power is supplied intermittently

to vehicle security lamp relay terminal 1

through smart entrance control unit terminal 39.

Ground is supplied

to vehicle security lamp relay terminal 2

through body grounds E54 and E12.

VEHICLE SECURITY (THEFT WARNING) SYSTEM

BL-47

C

D

E

F

G

H

J

K

L

M

A

B

BL

When the vehicle security system is triggered, ground is supplied intermittently

to horn relay terminal 2

through smart entrance control unit terminal 42.

The horn and headlamps operate intermittently.
The alarm automatically turns off after 50 seconds but will reactivate if the vehicle is tampered with again.

VEHICLE SECURITY SYSTEM DEACTIVATION

To deactivate the vehicle security system, a door must be unlocked with the key or keyfob.
When the key is used to unlock the door, smart entrance control unit terminal 10 receives a ground signal

through front door key cylinder switch LH terminal 3

through front door key cylinder switch LH terminal 2

through body grounds M14 and M68.

When the smart entrance control unit receives this signal or an unlock signal from keyfob, the vehicle security
system is deactivated (disarmed phase).

PANIC ALARM OPERATION

Remote keyless entry system may or may not operate vehicle security system (horn and headlamps) as
required.
When the remote keyless entry system is triggered, power is supplied intermittently

to vehicle security lamp relay terminal 1

through smart entrance control unit terminal 39

When the remote keyless entry system is triggered, ground is supplied intermittently

to horn relay terminal 2

through smart entrance control unit terminal 42.

The horn and headlamps operate intermittently.
The alarm automatically turns off after 30 seconds or when smart entrance control unit receives any signal
from keyfob.

BL-48

VEHICLE SECURITY (THEFT WARNING) SYSTEM

Circuit Diagram

EIS002CJ

WIWA0104E

 

 

 

 

 

 

 

Content   ..  150  151  152  153   ..