Nissan March K13. Manual - part 595

B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH

SEC-119

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

YES

>> Replace IPDM E/R. Refer to 

PCS-28, "Removal and Installation"

.

NO

>> Repair or replace harness.

SEC-120

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH

B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH

DTC Logic

INFOID:0000000006038609

DTC DETECTION LOGIC

NOTE:
If DTC B2110 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to 

PCS-

24, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Shift selector lever to the P position. 

2.

Turn ignition switch ON and wait 1 second or more.

3.

Shift selector lever to the N position and wait 1 second or more. 

4.

Shift selector lever to other than the P and N positions and wait 1 second or more. 

5.

Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT-III.

Is DTC detected?

YES

>> Go to 

SEC-120, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000006038610

1.

CHECK DTC WITH BCM

Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT-III.

Is DTC detected?

YES

>> Perform the trouble diagnosis related to the detected DTC. Refer to 

BCS-40, "DTC Index"

.

NO

>> GO TO 2.

2.

CHECK IPDM E/R SIGNAL CIRCUIT OPEN AND SHORT

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R connector.

3.

Disconnect transmission range switch connector.

4.

Check continuity between IPDM E/R harness connector and transmission range switch harness connec-
tor.

5.

Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B210F

INTER LOCK/PNP SW OFF

There is a difference between P/N position 
signal from transmission range switch and 
P/N position signal (CAN) from BCM.

• Harness or connectors

(The CAN communication line is open 
or shorted.)

• Harness or connectors

(Transmission range switch circuit is 
open or shorted.)

• Transmission range switch
• IPDM E/R
• BCM

IPDM E/R

Transmission range switch

Continuity

Connector

Terminal

Connector

Terminal

F115

76

F21

10

Existed 

(+)

(–)

Continuity

IPDM E/R

Connector

Terminal

F115

76

Ground

Not existed

B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH

SEC-121

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

YES

>> Replace IPDM E/R. Refer to 

PCS-28, "Removal and Installation"

.

NO

>> Repair or replace harness.

SEC-122

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

SECURITY INDICATOR LAMP

SECURITY INDICATOR LAMP

Component Function Check

INFOID:0000000006038616

1.

CHECK FUNCTION

1.

Perform “THEFT IND” in “ACTIVE TEST” mode of “IMMU” of “BCM” using CONSULT-III.

2.

Check security indicator lamp operation.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Go to 

SEC-122, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000006038617

1.

CHECK SECURITY INDICATOR LAMP POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect combination meter connector.

3.

Check voltage between combination meter harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO-1

>> Check 10 A fuse [No. 11, located in the fuse block (J/B)].

NO-2

>> Check harness for open or short between combination meter and fuse.

2.

CHECK SECURITY INDICATOR LAMP SIGNAL

1.

Connect combination meter connector.

2.

Disconnect BCM connector.

3.

Check voltage between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-57, "Removal and Installation"

.

NO

>> GO TO 3.

3.

CHECK SECURITY INDICATOR LAMP CIRCUIT

1.

Disconnect combination meter connector.

2.

Check continuity between combination meter harness connector and BCM harness connector.

3.

Check continuity between combination meter harness connector and ground.

Test item

Description

THEFT IND

ON

Security indicator lamp

Illuminates

OFF

Does not illuminate

(+)

(–)

Voltage (V)

(Approx.)

Combination meter

Connector

Terminal

M34

1

Ground

Battery voltage

(+)

(–)

Voltage (V)

(Approx.)

BCM

Connector

Terminal

M68

23

Ground

Battery voltage

Combination meter

BCM

Continuity

Connector

Terminal

Connector

Terminal

M34

31

M68

23

Existed