Nissan March K13. Manual - part 298

 

  Index      Nissan     Nissan March K13 - Service and Repair Manual)

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  296  297  298  299   ..

 

 

Nissan March K13. Manual - part 298

 

 

EXL-18

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)

HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)

INFOID:0000000005969677

WORK SUPPORT

*1

: With remote keyless entry system models

*2

: Factory setting

DATA MONITOR

Service item

Setting 

item

Setting

AUTO LIGHT LOGIC SET

*1

MODE 1

NOTE:
The item is displayed, but cannot be used

MODE 2

MODE 3

MODE 4

MODE 5

MODE 6

BATTERY SAVER SET

On

*2

With the exterior lamp battery saver function

Off

Without the exterior lamp battery saver function

Monitor item

[Unit]

Description

IGN ON SW
[On/Off]

Ignition switch (ON) status judged from IGN signal (ignition power supply)

ACC ON SW
[On/Off]

Ignition switch (ACC) status judged from ACC signal (ACC power supply)

VEH SPEED
[km/h]

The value of the vehicle speed received from combination meter with CAN commu-
nication

HI BEAM SW
[On/Off]

Each switch status that BCM judges from the combination switch reading function

HEAD LAMP SW1
[On/Off]

HEAD LAMP SW2
[On/Off]

PASSING SW
[On/Off]

FR FOG SW
[On/Off]

NOTE:
The item is indicated, but not monitored

AUTO LIGHT SW

*1

[On/Off]

NOTE:
The item is indicated, but not monitored

RR FOG SW

*1

[On/Off]

NOTE:
The item is indicated, but not monitored

DOOR SW-DR
[On/Off]

The switch status input from front door switch (driver side)

DOOR SW-AS
[On/Off]

The switch status input from front door switch (passenger side)

DOOR SW-RR
[On/Off]

The switch status input from rear door switch RH

DOOR SW- RL
[On/Off]

The switch status input from rear door switch LH

BACK DOOR SW
[On/Off]

The switch status input from back door switch

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)

EXL-19

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

*1

: With remote keyless entry system models

*2

: Without power door lock system models do not displayed, Without remote keyless entry system models are

displayed but does not monitored.

ACTIVE TEST

*

: With remote keyless entry system models

FLASHER

FLASHER : CONSULT-III Function (BCM - FLASHER)

INFOID:0000000005969678

DATA MONITOR

TURN SIGNAL R
[On/Off]

Each switch status that BCM judges from the combination switch reading function

TURN SIGNAL L
[On/Off]

TAIL LAMP SW
[On/Off]

KEY ON SW
[On/Off]

The switch status input from key on switch

KEYLESS LOCK

*2

[On/Off]

Lock signal status received from remote keyless entry receiver (integrated in the 
BCM)

PKB SW
[On/Off]

The parking brake switch status received from combination meter with CAN commu-
nication

ENGINE RUN
[On/Off]

The engine status received from ECM with CAN communication

OPTI SEN (DTCT)

*1

[V]

NOTE:
The item is indicated, but not monitored

OPTI SEN (FILT)

*1

[V]

NOTE:
The item is indicated, but not monitored

Monitor item

[Unit]

Description

Test item

Operation

Description

TAIL LAMP

On

Transmits the position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON.

Off

Stops the tail lamp request signal transmission.

HEAD LAMP

Hi

Transmits the high beam request signal with CAN communication to turn 
the headlamp (HI).

Lo

Transmits the low beam request signal with CAN communication to turn 
the headlamp (LO).

Off

Stops the high & low beam request signal transmission.

ILL DIM SIGNAL

*

On

NOTE:
The item is indicated, but cannot be tested.

Off

FR FOG LAMP

On

NOTE:
The item is indicated, but cannot be tested.

Off

Monitor item

[Unit]

Description

IGN ON SW
[On/Off]

Ignition switch (ON) status judged from IGN signal (ignition power supply)

EXL-20

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)

ACTIVE TEST

TURN SIGNAL R
[On/Off]

Each switch status that BCM detects from the combination switch reading function

TURN SIGNAL L
[On/Off]

HAZARD SW
[On/Off]

The switch status input from the hazard switch

Monitor item

[Unit]

Description

Test item

Operation

Description

FLASHER

RH

Outputs the voltage to blink the right side turn signal lamps.

LH

Outputs the voltage to blink the left side turn signal lamps.

Off

Stops the voltage to turn the turn signal lamps OFF.

DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)

EXL-21

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)

Diagnosis Description

INFOID:0000000006046538

AUTO ACTIVE TEST

Description

In auto active test, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Oil pressure warning lamp
• Front wiper (LO, HI)
• Parking lamps
• License plate lamps
• Tail lamps
• Front fog lamps
• Headlamps (LO, HI)
• A/C compressor (magnet clutch)
• Cooling fan

Operation Procedure

CAUTION:

Never perform auto active test in the following conditions.
• Engine is running
• CONSULT-III is connected

1.

Close the hood and lift the wiper arms from the windshield. (Prevent windshield damage due to wiper
operation)
NOTE:
When auto active test is performed with hood opened, sprinkle water on windshield beforehand.

2.

Turn the ignition switch OFF.

3.

Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the
ignition switch OFF.

CAUTION:

Close passenger door.

4.

Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test
starts.

CAUTION:

Engine starts when ignition switch is turned ON while brake pedal is depressed.

5.

The oil pressure warning lamp starts blinking when the auto active test starts.

6.

After a series of the following operations is repeated 3 times, auto active test is completed.

NOTE:
• When auto active test has to be cancelled halfway through test, turn the ignition switch OFF.
• When auto active test is not activated, door switch may be the cause. Check door switch. Refer to 

XX-XX,

"*****"

.

Inspection in Auto Active Test

When auto active test is actuated, the following operation sequence is repeated 3 times.

Operation 
sequence

Inspection location

Operation

1

Oil pressure warning lamp

Blinks continuously during operation of auto active test 

2

Front wiper

LO for 5 seconds 

 HI for 5 seconds

3

• Parking  lamps
• License plate lamps
• Tail lamps
• Front fog lamps

10 seconds

4

Headlamps

LO for 10 seconds 

HI ON 

 OFF 5 times

5

A/C compressor (magnet clutch)

ON 

 OFF 5 times

6

Cooling fan

LO for 5 seconds 

 MID for 3 seconds 

 HI for 2 seconds

 

 

 

 

 

 

 

Content   ..  296  297  298  299   ..