Nissan March K13. Manual - part 118

 

  Index      Nissan     Nissan March K13 - Service and Repair Manual)

 

Search            

 

 

 

 

 

 

 

  

 

Content   ..  116  117  118  119   ..

 

 

Nissan March K13. Manual - part 118

 

 

DOOR LOCK ACTUATOR

DLK-183

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

DOOR LOCK ACTUATOR

DRIVER SIDE

DRIVER SIDE : Component Function Check

INFOID:0000000005949068

1.

CHECK FUNCTION

1.

Select “DOOR LOCK” of “BCM” using CONSULT-III.

2.

Select “DOOR LOCK” in “ACTIVE TEST” mode.

3.

Touch “ALL LOCK” or “ALL UNLK” to check that it works normally.

Is the inspection result normal?

YES

>> Door lock actuator is OK.

NO

>> Refer to 

DLK-183, "DRIVER SIDE : Diagnosis Procedure"

.

DRIVER SIDE : Diagnosis Procedure

INFOID:0000000005949069

1.

CHECK DOOR LOCK ACTUATOR INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect front door lock assembly (driver side) connector.

3.

Check voltage between front door lock assembly (driver side) harness connector and ground.

Is the inspection result normal?

YES

>> Replace front door lock assembly (driver side).

NO

>> GO TO 2.

2.

CHECK DOOR LOCK ACTUATOR CIRCUIT

1.

Disconnect BCM connector and all door lock actuator connector.

2.

Check continuity between BCM harness connector and front door lock assembly (driver side) harness
connector. 

3.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK BCM OUTPUT SIGNAL

1.

Connect BCM connector.

2.

Check voltage between BCM harness connector and ground.

(+)

(–)

Condition

Voltage

(Approx.)

Front door lock assembly

(driver side)

Connector

Terminal

D28

5

Ground

Door lock and unlock switch

Lock

12 V

6

Unlock

BCM

Front door lock assembly (driver side)

Continuity 

Connector

Terminal

Connector

Terminal

M67

66

D28

6

Existed

65

5

BCM

Ground

Continuity 

Connector

Terminal

M70

66

Not existed

65

DLK-184

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

DOOR LOCK ACTUATOR

Is the inspection result normal?

YES

>> Check for internal short of each door lock actuator.

NO

>> Replace BCM. Refer to 

BCS-99, "Removal and Installation"

.

PASSENGER SIDE

PASSENGER SIDE : Component Function Check

INFOID:0000000005949071

1.

CHECK FUNCTION

1.

Select “DOOR LOCK” of “BCM” using CONSULT-III.

2.

Select “DOOR LOCK” in “ACTIVE TEST” mode.

3.

Touch “ALL LOCK” or “ALL UNLK” to check that it works normally.

Is the inspection result normal?

YES

>> Door lock actuator is OK.

NO

>> Refer to 

DLK-184, "PASSENGER SIDE : Diagnosis Procedure"

.

PASSENGER SIDE : Diagnosis Procedure

INFOID:0000000005949072

1.

CHECK DOOR LOCK ACTUATOR INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect front door lock assembly (passenger side) connector.

3.

Check voltage between front door lock assembly (passenger side) harness connector and ground.

Is the inspection result normal?

YES

>> Replace front door lock assembly (passenger side).

NO

>> GO TO 2.

2.

CHECK DOOR LOCK ACTUATOR CIRCUIT

1.

Disconnect BCM connector and all door lock actuator connector. 

2.

Check continuity between BCM harness connector and front door lock assembly (passenger side) har-
ness connector. 

3.

Check continuity between BCM harness connector and ground.

(+)

(–)

Condition

Voltage

(Approx.)

BCM

Connector

Terminal

M67

65

Ground

Door lock and unlock switch

Lock

12 V

66

Unlock

(+)

(–)

Condition

Voltage

(Approx.)

Front door lock assembly

(passenger side)

Connector

Terminal

D9

1

Ground

Door lock and unlock switch

Lock

12 V

2

Unlock

BCM

Front door lock assembly (passenger side)

Continuity 

Connector

Terminal

Connector

Terminal

M67

65

D9

1

Existed

66

2

DOOR LOCK ACTUATOR

DLK-185

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK BCM OUTPUT SIGNAL

1.

Connect BCM connector.

2.

Check voltage between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Check for internal short of each door lock actuator.

NO

>> Replace BCM. Refer to 

BCS-99, "Removal and Installation"

.

REAR LH

REAR LH : Component Function Check

INFOID:0000000005949074

1.

CHECK FUNCTION

1.

Select “DOOR LOCK” of “BCM” using CONSULT-III.

2.

Select “DOOR LOCK” in “ACTIVE TEST” mode.

3.

Touch “ALL LOCK” or “ALL UNLK” to check that it works normally.

Is the inspection result normal?

YES

>> Door lock actuator is OK.

NO

>> Refer to 

DLK-186, "REAR RH : Diagnosis Procedure"

.

REAR LH : Diagnosis Procedure

INFOID:0000000005949075

1.

CHECK DOOR LOCK ACTUATOR INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect rear door lock assembly LH connector.

3.

Check voltage between rear door lock assembly LH harness connector and ground.

Is the inspection result normal?

YES

>> Replace rear door lock assembly LH.

NO

>> GO TO 2.

2.

CHECK DOOR LOCK ACTUATOR CIRCUIT

1.

Disconnect BCM connector and all door lock actuator.

2.

Check continuity between BCM harness connector and rear door lock assembly LH harness connector. 

BCM

Ground

Continuity 

Connector

Terminal

M67

65

Not existed

66

(+)

(–)

Condition

Voltage

(Approx.)

BCM

Connector

Terminal

M67

65

Ground

Door lock and unlock switch

Lock

12 V

66

Unlock

(+)

(–)

Condition

Voltage

(Approx.)

Rear door lock assembly LH

Connector

Terminal

D65

1

Ground

Door lock and unlock switch

Lock

12 V

2

Unlock

DLK-186

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

DOOR LOCK ACTUATOR

3.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK BCM OUTPUT SIGNAL

1.

Connect BCM connector.

2.

Check voltage between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Check for internal short of each door lock actuator.

NO

>> Replace BCM. Refer to 

BCS-99, "Removal and Installation"

.

REAR RH

REAR RH : Component Function Check

INFOID:0000000005949077

1.

CHECK FUNCTION

1.

Select “DOOR LOCK” of “BCM” using CONSULT-III.

2.

Select “DOOR LOCK” in “ACTIVE TEST” mode.

3.

Touch “ALL LOCK” or “ALL UNLK” to check that it works normally.

Is the inspection result normal?

YES

>> Door lock actuator is OK.

NO

>> Refer to 

DLK-186, "REAR RH : Diagnosis Procedure"

.

REAR RH : Diagnosis Procedure

INFOID:0000000005949078

1.

CHECK DOOR LOCK ACTUATOR INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect rear door lock assembly RH connector.

3.

Check voltage between rear door lock assembly RH harness connector and ground.

Is the inspection result normal?

BCM

Rear door lock assembly LH

Continuity 

Connector

Terminal

Connector

Terminal

M67

65

D65

1

Existed

66

2

BCM

Ground

Continuity 

Connector

Terminal

M67

65

Not existed

66

(+)

(–)

Condition

Voltage

(Approx.)

BCM

Connector

Terminal

M67

65

Ground

Door lock and unlock switch

Lock

12 V

66

Unlock

(+)

(–)

Condition

Voltage

(Approx.)

Rear door lock assembly RH

Connector

Terminal

D45

5

Ground

Door lock and unlock switch

Lock

12 V

6

Unlock

 

 

 

 

 

 

 

Content   ..  116  117  118  119   ..