Nissan March K13. Manual - part 17

BCS

BCM

BCS-41

< ECU DIAGNOSIS INFORMATION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

U0415: VEHICLE SPEED

×

—

×

BCS-49

B2013: ID DISCORD BCM-S/L

×

×

×

SEC-54

B2014: CHAIN OF S/L-BCM

×

×

×

SEC-55

B2192: ID DISCORD BCM-ECM

×

—

—

SEC-46

B2193: CHAIN OF BCM-ECM

×

—

—

SEC-48

B2195: ANTI-SCANNING

×

—

—

SEC-49

B2198: NATS ANTENNA AMP

×

—

—

SEC-50

B2553: IGNITION RELAY

—

×

×

PCS-71

B2555: STOP LAMP

—

×

×

SEC-58

B2556: PUSH-BTN IGN SW

—

×

×

SEC-60

B2557: VEHICLE SPEED

×

×

×

SEC-62

B2562: LOW VOLTAGE

—

×

—

BCS-50

B2601: SHIFT POSITION

×

×

×

SEC-63

B2602: SHIFT POSITION

×

×

×

SEC-66

B2603: SHIFT POSI STATUS

×

×

×

SEC-69

B2604: PNP/CLUTCH SW

×

×

×

SEC-73

B2605: PNP/CLUTCH SW

×

×

×

SEC-76

B2608: STARTER RELAY

×

×

×

SEC-78

B2609: S/L STATUS

×

×

×

SEC-80

B260B: STEERING LOCK UNIT

×

×

×

SEC-83

B260C: STEERING LOCK UNIT

—

×

×

SEC-84

B260D: STEERING LOCK UNIT

×

×

×

SEC-85

B260F: ENG STATE SIG LOST

×

×

×

SEC-86

B2612: S/L STATUS

×

×

×

SEC-87

B2614: BCM

—

×

×

PCS-73

B2615: BCM

—

×

×

PCS-75

B2616: BCM

—

×

×

PCS-77

B2618: BCM

—

×

×

PCS-79

B2619: BCM

×

×

×

SEC-90

B261A: PUSH-BTN IGN SW

—

×

×

PCS-80

B2621: INSIDE ANTENNA

—

×

—

DLK-46

B2622: INSIDE ANTENNA

—

×

—

DLK-48

B2623: INSIDE ANTENNA

—

×

—

DLK-50

B2626: OUTSIDE ANTENNA

—

×

—

DLK-52

B2627: OUTSIDE ANTENNA

—

×

—

DLK-54

B2628: OUTSIDE ANTENNA

—

×

—

DLK-56

B26E9: LOCK MALFUNCTION

—

×

×

 (Turn ON for 

15 seconds)

SEC-91

B26EF: STRG LCK RELAY OFF

×

×

×

SEC-92

B26F0: STRG LCK RELAY ON

×

×

×

SEC-95

B26F1: IGN RELAY OFF

×

×

×

PCS-82

B26F2: IGN RELAY ON

×

×

×

PCS-84

B26F3: START CONT RLY ON

×

×

×

SEC-97

CONSULT display

Fail-safe

Freeze Frame Data

•Vehicle Speed

•Odo/Trip Meter

•Vehicle Condition

Intelligent Key 

warning lamp 

ON

Reference page

BCS-42

< ECU DIAGNOSIS INFORMATION >

[WITH INTELLIGENT KEY SYSTEM]

BCM

B26F4: START CONT RLY OFF

×

×

×

SEC-98

B26F5: STRG LCK STS SW

—

×

×

SEC-99

B26F6: BCM

—

×

×

PCS-86

B26F7: BCM

×

×

×

SEC-102

B26FC: KEY REGISTRATION

—

×

×

SEC-103

CONSULT display

Fail-safe

Freeze Frame Data

•Vehicle Speed

•Odo/Trip Meter

•Vehicle Condition

Intelligent Key 

warning lamp 

ON

Reference page

BCS

BCM

BCS-43

< WIRING DIAGRAM >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

WIRING DIAGRAM

BCM

Wiring Diagram

INFOID:0000000006014845

For connector terminal arrangements, harness layouts, and alphabets in a 

 (option abbreviation; if not

described in wiring diagram), refer to 

GI-12, "Connector Information"

.

回路図待ち。

。

。

BCS-44

< BASIC INSPECTION >

[WITH INTELLIGENT KEY SYSTEM]

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT

BASIC INSPECTION

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT

Description

INFOID:0000000006046470

BEFORE REPLACEMENT

When replacing BCM, save or print current vehicle specification with CONSULT-III configuration before
replacement.
NOTE:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after
replacing BCM.

AFTER REPLACEMENT

CAUTION:

• When replacing BCM, you must perform “WRITE CONFIGURATION” with CONSULT-III.
- Complete the procedure of “WRITE CONFIGURATION” in order.
- If you set incorrect “WRITE CONFIGURATION”, incidents might occur.
- Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• When replacing BCM, perform the system initialization (NATS).

Work Procedure

INFOID:0000000006046471

1.

SAVING VEHICLE SPECIFICATION

CONSULT-III Configuration

Perform “READ CONFIGURATION” to save or print current vehicle specification. Refer to 

BCS-45, "Descrip-

tion"

.

NOTE:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after
replacing BCM.

>> GO TO 2.

2.

REPLACE BCM

Replace BCM. Refer to 

BCS-57, "Removal and Installation"

.

>> GO TO 3.

3.

WRITING VEHICLE SPECIFICATION

CONSULT-III Configuration

Perform “WRITE CONFIGURATION - Config file” or “WRITE CONFIGURATION - Manual selection” to write
vehicle specification. Refer to 

BCS-45, "Work Procedure"

.

>> GO TO 4.

4.

INITIALIZE BCM (NATS)

Perform BCM initialization. (NATS)

>> WORK END