Nissan Pathfinder (2010 year). Manual - part 619

 

  Index      Manuals     Nissan Pathfinder (2010 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     617      618      619      620     ..

 

 

Nissan Pathfinder (2010 year). Manual - part 619

 

 

TM-80

< COMPONENT DIAGNOSIS >

P1721 VEHICLE SPEED SIGNAL

OK or NG

OK

>> GO TO 4.

NG

>> Repair or replace damaged parts.

4.

CHECK DTC

Perform “DTC Confirmation Procedure”.

• Refer to 

TM-79, "DTC Confirmation Procedure"

.

OK or NG

OK

>>

INSPECTION END

NG

>> GO TO 5.

5.

CHECK TCM POWER SUPPLY AND GROUND CIRCUIT

Check TCM power supply and ground circuit. Refer to 

TM-100, "Diagnosis Procedure"

.

OK or NG

OK

>> GO TO 6.

NG

>> Repair or replace damaged parts.

6.

DETECT MALFUNCTIONING ITEM

Check the following.

• The A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG

OK

>> Replace the control valve with TCM. Refer to 

TM-174, "Removal and Installation"

.

NG

>> Repair or replace damaged parts.

2010 Pathfinder

P1730 INTERLOCK

TM-81

< COMPONENT DIAGNOSIS >

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P1730 INTERLOCK

Description

INFOID:0000000005258071

• Fail-safe function to detect interlock conditions.

On Board Diagnosis Logic

INFOID:0000000005258072

• This is an OBD-II self-diagnostic item.

• Diagnostic trouble code “P1730” with CONSULT-III or 12th judgment flicker without CONSULT-III is detected

when TCM does not receive the proper voltage signal from the sensor and switch.

• TCM monitors and compares gear position and conditions of each ATF pressure switch when gear is steady.

Possible Cause

INFOID:0000000005258073

• Harness or connectors

(The solenoid and switch circuit is open or shorted.)

• Low coast brake solenoid valve

• ATF pressure switch 2

DTC Confirmation Procedure

INFOID:0000000005258074

NOTE:

If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”

and wait at least 10 seconds before performing the next test.

After the repair, perform the following procedure to confirm the malfunction is eliminated.

 WITH CONSULT-III

1. Turn ignition switch “ON”. (Do not start engine.)

2. Select “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.

3. Start engine.

4. Drive vehicle and maintain the following conditions for at least 2 consecutive seconds.

SLCT LVR POSI: “D” position 

5. If DTC is detected, go to 

TM-81, "Diagnosis Procedure"

.

 WITH GST

Follow the procedure “WITH CONSULT-III”.

Judgement of Interlock

INFOID:0000000005258075

When interlock is judged to be malfunctioning, the vehicle should be fixed in 2GR, and should be set in a con-

dition in which it can travel.

When one of the following fastening patterns is detected, the fail-safe function in correspondence with the indi-

vidual pattern should be performed.

NOTE:

When the vehicle is driven in 2GR, a input speed sensor malfunction is displayed, but this is not a tin-

put speed sensor malfunction.

When interlock is detected at the 3GR or more, it is locked at the 2GR.

Diagnosis Procedure

INFOID:0000000005258076

1.

SELF-DIAGNOSIS

With CONSULT-III

1. Drive vehicle.

2. Stop vehicle and turn ignition switch OFF.

3. Turn ignition switch ON.

4. Select “SELF-DIAG RESULTS” mode for “TRANSMISSION” with CONSULT-III.

Without CONSULT-III

1. Drive vehicle.

2. Stop vehicle and turn ignition switch OFF.

3. Turn ignition switch ON.

2010 Pathfinder

TM-82

< COMPONENT DIAGNOSIS >

P1730 INTERLOCK

4. Perform self-diagnosis. Refer to 

TM-41, "Diagnosis Procedure without CONSULT-III"

.

 OK or NG

OK

>> GO TO 2.

NG

>> Check low coast brake solenoid valve circuit and function. Refer to 

TM-93

TM-95

.

2.

CHECK DTC

Perform “DTC Confirmation Procedure”.

• Refer to 

TM-81, "DTC Confirmation Procedure"

.

OK or NG

OK

>>

INSPECTION END

NG

>> GO TO 3.

3.

CHECK TCM POWER SUPPLY AND GROUND CIRCUIT

Check TCM power supply and ground circuit. Refer to 

TM-100, "Diagnosis Procedure"

.

OK or NG

OK

>> GO TO 4.

NG

>> Repair or replace damaged parts.

4.

DETECT MALFUNCTIONING ITEM

Check the following.

• The A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG

OK

>> Replace the control valve with TCM. Refer to 

TM-174, "Removal and Installation"

.

NG

>> Repair or replace damaged parts.

2010 Pathfinder

P1731 1ST ENGINE BRAKING

TM-83

< COMPONENT DIAGNOSIS >

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P1731 1ST ENGINE BRAKING

Description

INFOID:0000000005258077

Fail-safe function to prevent sudden decrease in speed by engine brake other than at “1” position.

CONSULT-III Reference Value in Data Monitor Mode

INFOID:0000000005258078

On Board Diagnosis Logic

INFOID:0000000005258079

• This is not an OBD-II self-diagnostic item.

• Diagnostic trouble code “P1731” with CONSULT-III or 13th judgment flicker without CONSULT-III is detected

under the following conditions.

- When TCM does not receive the proper voltage signal from the sensor.

- When TCM monitors each ATF pressure switch and solenoid monitor value, and detects as irregular when

engine brake of 1st gear acts other than at “1” position.

Possible Cause

INFOID:0000000005258080

• Harness or connectors

(The sensor circuit is open or shorted.)

• Low coast brake solenoid valve

• ATF pressure switch 2

DTC Confirmation Procedure

INFOID:0000000005258081

NOTE:

If “DTC Confirmation Procedure” has been previously preformed, always turn ignition switch “OFF”

and wait at least 10 seconds before performing the next test.

After the repair, perform the following procedure to confirm the malfunction is eliminated.

 WITH CONSULT-III

1. Turn ignition switch “ON”. (Do not start engine.)

2. Select “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.

3. Start engine.

4. Drive vehicle and maintain the following conditions for at least 2 consecutive seconds.

ENGINE SPEED: 1,200 rpm

SLCT LVR POSI: “1” position 

GEAR: 1st 

5. If DTC is detected, go to 

TM-83, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000005258082

1.

CHECK INPUT SIGNALS

With CONSULT-III

1. Start the engine.

2. Select “SELECTION FROM MENU” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.

3. Drive vehicle in the “1” position (1GR), and confirm the ON/OFF actuation of “ATF PRES SW 2” and “ON

OFF SOL”.

OK or NG

OK

>> GO TO 4.

NG

>> GO TO 2.

Item name

Condition 

Display value

ON OFF SOL

Low coast brake engaged. Refer to 

TM-10

.

ON

Low coast brake disengaged. Refer to 

TM-10

.

OFF

ATF PRES SW 2

Low coast brake engaged. Refer to 

TM-10

.

ON

Low coast brake disengaged. Refer to 

TM-10

.

OFF

2010 Pathfinder

TM-84

< COMPONENT DIAGNOSIS >

P1731 1ST ENGINE BRAKING

2.

CHECK TCM POWER SUPPLY AND GROUND CIRCUIT

Check TCM power supply and ground circuit. Refer to 

TM-100, "Diagnosis Procedure"

.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace damaged parts.

3.

DETECT MALFUNCTIONING ITEM

Check the following.

• The A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG

OK

>> Replace the control valve with TCM. Refer to 

TM-174, "Removal and Installation"

.

NG

>> Repair or replace damaged parts.

4.

CHECK DTC

Perform “DTC Confirmation Procedure”.

• Refer to 

TM-83, "DTC Confirmation Procedure"

.

OK or NG

OK

>>

INSPECTION END

NG

>> GO TO 2.

2010 Pathfinder

P1752 INPUT CLUTCH SOLENOID

TM-85

< COMPONENT DIAGNOSIS >

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P1752 INPUT CLUTCH SOLENOID

Description

INFOID:0000000005258083

Input clutch solenoid valve is controlled by the TCM in response to signals sent from the transmission range

switch, output speed sensor and accelerator pedal position sensor (throttle position sensor). Gears will then

be shifted to the optimum position.

CONSULT-III Reference Value in Data Monitor Mode

INFOID:0000000005258084

On Board Diagnosis Logic

INFOID:0000000005258085

• This is an OBD-II self-diagnostic item.

• Diagnostic trouble code “P1752” with CONSULT-III or 5th judgment flicker without CONSULT-III is detected

under the following conditions.

- When TCM detects an improper voltage drop when it tries to operate the solenoid valve.

- When TCM detects as irregular by comparing target value with monitor value.

Possible Cause

INFOID:0000000005258086

• Harness or connectors

(The solenoid circuit is open or shorted.)

• Input clutch solenoid valve 

DTC Confirmation Procedure

INFOID:0000000005258087

CAUTION:

Always drive vehicle at a safe speed.

NOTE:

If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”

and wait at least 10 seconds before performing the next test.

After the repair, perform the following procedure to confirm the malfunction is eliminated.

 WITH CONSULT-III

1. Turn ignition switch “ON”. (Do not start engine.)

2. Select “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.

3. Start engine.

4. Drive vehicle and maintain the following conditions for at least 5 consecutive seconds.

ACCELE POSI: 1.5/8 - 2.0/8

SLCT LVR POSI: “D” position 

GEAR: 3rd 

 4th (I/C ON/OFF) 

Driving location: Driving the vehicle uphill (increased engine load) will help maintain the driving

conditions required for this test.

5. If DTC is detected go to 

TM-85, "Diagnosis Procedure"

.

 WITH GST

Follow the procedure “WITH CONSULT-III”.

Diagnosis Procedure

INFOID:0000000005258088

1.

CHECK INPUT SIGNAL

With CONSULT-III

1. Turn ignition switch ON.

2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.

3. Start the engine.

4. Read out the value of “I/C SOLENOID” while driving.

Item name

Condition 

Display value (Approx.)

I/C SOLENOID

Input clutch disengaged. Refer to 

TM-10

.

0.6 - 0.8 A

Input clutch engaged. Refer to 

TM-10

.

0  -  0.05  A

2010 Pathfinder

TM-86

< COMPONENT DIAGNOSIS >

P1752 INPUT CLUTCH SOLENOID

OK or NG

OK

>> GO TO 4.

NG

>> GO TO 2.

2.

CHECK TCM POWER SUPPLY AND GROUND CIRCUIT

Check TCM power supply and ground circuit. Refer to 

TM-100, "Diagnosis Procedure"

.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace damaged parts.

3.

DETECT MALFUNCTIONING ITEM

Check the following.

• The A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG

OK

>> Replace the control valve with TCM. Refer to 

TM-174, "Removal and Installation"

.

NG

>> Repair or replace damaged parts.

4.

CHECK DTC

Perform “DTC Confirmation Procedure”.

• Refer to 

TM-85, "DTC Confirmation Procedure"

.

OK or NG

OK

>>

INSPECTION END

NG

>> GO TO 2.

2010 Pathfinder

P1757 FRONT BRAKE SOLENOID

TM-87

< COMPONENT DIAGNOSIS >

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P1757 FRONT BRAKE SOLENOID

Description

INFOID:0000000005258089

Front brake solenoid valve is controlled by the TCM in response to signals sent from the transmission range

switch, output speed sensor and accelerator pedal position sensor (throttle position sensor). Gears will then

be shifted to the optimum position.

CONSULT-III Reference Value in Data Monitor Mode

INFOID:0000000005258090

On Board Diagnosis Logic

INFOID:0000000005258091

• This is an OBD-II self-diagnostic item.

• Diagnostic trouble code “P1757” with CONSULT-III or 6th judgment flicker without CONSULT-III is detected

under the following conditions.

- When TCM detects an improper voltage drop when it tries to operate the solenoid valve.

- When TCM detects as irregular by comparing target value with monitor value.

Possible Cause

INFOID:0000000005258092

• Harness or connectors

(The solenoid circuit is open or shorted.)

• Front brake solenoid valve 

DTC Confirmation Procedure

INFOID:0000000005258093

CAUTION:

Always drive vehicle at a safe speed.

NOTE:

If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”

and wait at least 10 seconds before performing the next test.

After the repair, perform the following procedure to confirm the malfunction is eliminated.

 WITH CONSULT-III

1. Turn ignition switch “ON”. (Do not start engine.)

2. Select “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.

3. Start engine.

4. Drive vehicle and maintain the following conditions for at least 5 consecutive seconds.

ACCELE POSI: 1.5/8 - 2.0/8

SLCT LVR POSI: “D” position 

GEAR: 3rd 

 4th (FR/B ON/OFF) 

Driving location: Driving the vehicle uphill (increased engine load) will help maintain the driving

conditions required for this test.

5. If DTC is detected go to 

TM-87, "Diagnosis Procedure"

.

 WITH GST

Follow the procedure “WITH CONSULT-III”.

Diagnosis Procedure

INFOID:0000000005258094

1.

CHECK INPUT SIGNAL

With CONSULT-III

1. Turn ignition switch ON.

2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.

3. Start engine.

4. Read out the value of “FR/B SOLENOID” while driving.

Item name

Condition 

Display value (Approx.)

FR/B SOLENOID

Front brake engaged. Refer to 

TM-10

.

0.6 - 0.8 A

Front brake disengaged. Refer to 

TM-10

.

0  -  0.05  A

2010 Pathfinder

 

 

 

 

 

 

 

Content      ..     617      618      619      620     ..