Nissan Pathfinder. Manual - part 1175

 

  Index      Nissan     Nissan Pathfinder (2014 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1173  1174  1175  1176   ..

 

 

Nissan Pathfinder. Manual - part 1175

 

 

P2765 INPUT SPEED SENSOR B

TM-159

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10E]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

>> GO TO 2.

2.

CHECK DTC DETECTION

1. Start the engine.

2. Drive the vehicle.

3. Maintain the following conditions for 10 seconds or more.

4. Stop the vehicle.

5. Check the first trip DTC.
Is “P2765” detected?

YES

>> Go to 

TM-159, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009177615

1.

CHECK OUTPUT SPEED SENSOR POWER CIRCUIT 

1. Turn ignition switch OFF.

2. Disconnect output speed sensor connector.

3. Turn ignition switch ON.

4. Check voltage between output speed sensor harness connector terminal and ground. 

Is the inspection result normal?

YES 

>> GO TO 2.

NO

>> GO TO 6.

2.

CHECK OUTPUT SPEED SENSOR GROUND CIRCUIT 

Check continuity between output speed sensor harness connector terminal and ground. 

Is the inspection result normal?

YES 

>> GO TO 3.

NO

>> Repair or replace malfunctioning parts.

3.

CHECK CIRCUIT BETWEEN OUTPUT SPEED SENSOR AND TCM (PART 1)

1. Turn ignition switch OFF.

2. Disconnect TCM connector.

3. Check continuity between output speed sensor harness connector terminal and TCM harness connector

terminal.

Is the inspection result normal?

Selector lever

: “D” position

Engine speed

: 1,200 rpm or more

Vehicle speed

: 55 km/h (34 MPH) or more

+

Voltage

Output speed sensor

Connector

Terminal

F23

3

Ground

10 – 16 V

Output speed sensor

Continuity

Connector

Terminal

F23

1

Ground

Existed

Output speed sensor

TCM

Continuity

Connector

Terminal

Connector

Terminal

F23

2

F15

34

Existed

TM-160

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10E]

P2765 INPUT SPEED SENSOR B

YES 

>> GO TO 4.

NO

>> Repair or replace malfunctioning parts.

4.

CHECK CIRCUIT BETWEEN OUTPUT SPEED SENSOR AND TCM (PART 2)

Check continuity between output speed sensor harness connector terminal and ground. 

Is the inspection result normal?

YES 

>> GO TO 5.

NO

>> Repair or replace malfunctioning parts.

5.

CHECK TCM INPUT SIGNALS

1. Connect all of disconnected connectors.

2. Lift the vehicle.

3. Start the engine.

4. Check frequency of output speed sensor.

Is the inspection result normal?

YES >> Check 

intermittent incident. Refer to 

GI-49, "Intermittent Incident"

.

NO

>> Replace output speed sensor. Refer to 

TM-203, "Removal and Installation"

.

6.

DETECT MALFUNCTIONING ITEMS

Check the following items:

• Open circuit or short circuit in harness between ignition switch and IPDM E/R. Refer to 

PG-23, "Wiring Dia-

gram - IGNITION POWER SUPPLY -"

.

• Open circuit or short circuit in harness between IPDM E/R harness connector terminal 61 and output speed

sensor harness connector terminal 3.

• 10A fuse (No.46, located in the IPDM E/R). Refer to 

PG-81, "Terminal Arrangement"

.

• IPDM E/R
Is the check result normal?

YES

>> Check intermittent incident. Refer to 

GI-49, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

Output speed sensor

Continuity

Connector

Terminal

F23

2

Ground

Not existed

+

Condition

Frequency

(Approx.)

TCM

Connector

Terminal

F15

34

Ground

• Selector lever: “L” position
• Vehicle speed: 20 km/h (12 MPH)

200 Hz

JSDIA1904GB

P2813 SELECT SOLENOID

TM-161

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10E]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P2813 SELECT SOLENOID

DTC Logic

INFOID:0000000009177616

DTC DETECTION LOGIC

NOTE:

DC stands for “DRIVING CYCLE” and indicates a series of driving cycle of “Ignition switch OFF 

→ ON → driv-

ing 

→ OFF”.

DTC CONFIRMATION PROCEDURE

CAUTION:

Be careful of the driving speed.

1.

PREPARATION BEFORE WORK

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

Possible causes

P2813

SELECT SOLENOID
(Select solenoid)

When any of 1, or 2 is satisfied:
1.

When all the following conditions are es-
tablished three times in 1DC

-

Precondition

DTC other than the applicable DTC is not 
detected.

Throttle position: More than 6.27 deg.

Vehicle speed: Less than 3 km/h (1 
MPH)

CVT fluid temperature: More than 20

°C 

(68

°F)

Selector lever: Other than P, N

Turbine speed when performed N 

→ D, 

N (P) 

→ R: More than 500 rpm

TCM power supply voltage: More than 11 
V

-

Detection time

→ D: 0.4 seconds

→ R: 0.3 seconds

→ R: 0.3 seconds

2.

When all of the following conditions are 
satisfied and this state is maintained for 
30 seconds:

-

The counting of time continues while all 
of the following conditions are satisfied 
and stops when the conditions become 
unsatisfied (the count is maintained). 
When accumulated time reaches 30 sec-
onds (Clutch is judged as engaged and 
the count is reset.)

Selector lever: Other than P, N

Vehicle speed: Less than 3 km/h (1 
MPH)

Differences between primary pulley 
speed and secondary speed: Less than 
120 rpm

Clutch instructions pressure: 0.95 MPa 
or more

Differences between turbine speed and 
input speed: Less than 200 rpm

Turbine speed – speed: More than 450 
rpm

 DTC other than the applicable DTC is 
not detected.

TCM power supply voltage: More than 11 
V

Select solenoid valve

TM-162

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10E]

P2813 SELECT SOLENOID

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION 1

1. Start the engine.

2. Maintain the following conditions. (Keep 30seconds or more after the selector lever shifted.)

3. Check the first trip DTC.
Is “P2813”detected?

YES

>> Go to 

TM-162, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009177617

1.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-49, "Intermittent Incident"

.

Is the inspection result normal?

YES 

>> Replace transaxle assembly. Refer to 

TM-214, "Removal and Installation"

.

NO

>> Repair or replace malfunctioning parts.

Selector lever

: N

→ D, N → R, P→ R

 

 

 

 

 

 

 

Content   ..  1173  1174  1175  1176   ..