Nissan Teana J32. Manual - part 616

SERVICE DATA AND SPECIFICATIONS (SDS)

FAX-35

< SERVICE DATA AND SPECIFICATIONS (SDS) 

C

E

F

G

H

I

J

K

L

M

A

B

FAX

N

O

P

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

Wheel Bearing

INFOID:0000000003811089

Drive Shaft

INFOID:0000000003811090

VQ25DE

VQ35DE

Item

Standard

Axial end play

0.05 mm (0.002 in) or less

Item

Left side

Right side

Grease quantity

Wheel side

88 – 108 g (3.11 – 3.80 oz)

Transaxle side

153 – 166 g (5.40 – 5.85 oz)

Boots installed length

Wheel side

186.7 mm (7.35 in)

Transaxle side

153.4 mm (6.04 in)

Dimension of dynamic damper

207 – 213 mm (8.15 – 8.39 in)

Item

Left side

Right side

Grease quantity

Wheel side

170 – 190 g (6.00 – 6.70 oz)

Transaxle side

155 – 175 g (5.47 – 6.17 oz)

Boots installed length

Wheel side

158.6 mm (6.24 in)

Transaxle side

163.67 mm (6.44 in)

Dimension of dynamic damper

—

202 – 208 mm (7.95 – 8.19 in)

FL-1

ENGINE

C

D

E

F

G

H

I

J

K

L

M

SECTION 

FL

A

FL

N

O

P

CONTENTS

FUEL SYSTEM

PRECAUTION ...............................................

2

PRECAUTIONS ...................................................

2

General Precautions  .................................................

2

PREPARATION ............................................

3

PREPARATION ...................................................

3

Commercial Service Tool  ..........................................

3

ON-VEHICLE MAINTENANCE .....................

4

FUEL SYSTEM  ....................................................

4

Inspection ..................................................................

4

Quick Connector  .......................................................

4

ON-VEHICLE REPAIR ..................................

5

FUEL LEVEL SENSOR UNIT, FUEL FILTER 
AND FUEL PUMP ASSEMBLY  .........................

5

Exploded View ..........................................................

5

Removal and Installation  ..........................................

5

Inspection .................................................................

8

FUEL TANK  .......................................................

9

Exploded View ..........................................................

9

Removal and Installation  ..........................................

9

Inspection ................................................................

10

SERVICE DATA AND SPECIFICATIONS 
(SDS) ............................................................

11

SERVICE DATA AND SPECIFICATIONS 
(SDS) .................................................................

11

Fuel Tank .................................................................

11

FL-2

< PRECAUTION >

PRECAUTIONS

PRECAUTION

PRECAUTIONS

General Precautions

INFOID:0000000003793245

WARNING:

When replacing fuel line parts, be sure to observe the following.
• Put a “CAUTION: FLAMMABLE” sign in the workshop.
• Be sure to work in a well ventilated area and furnish workshop with a CO

2

 fire extinguisher. 

• Never smoke while servicing fuel system. Keep open flames and sparks away from the work area.

CAUTION:

• Use gasoline required by the regulations for octane number. Refer to 

GI-29, "Fuel"

.

• Before removing fuel line parts, perform out the following procedures:
- Put drained fuel in an explosion-proof container and put the lid on securely. Keep the container in

safe area.

- Release fuel pressure from the fuel lines. Refer to 

EC-411, "Inspection"

.

- Disconnect the battery cable from the negative terminal. 
• Always replace O-ring and clamps with new ones.
• Never kink or twist tubes when they are being installed.
• Never tighten hose clamps excessively to avoid damaging hoses. 
• After installing tubes, check there is no fuel leakage at connections in the following steps.
- Apply fuel pressure to fuel lines with turning ignition switch “ON” (with engine stopped). Then check

for fuel leakage at connections.

- Start engine and rev it up and check for fuel leakage at connections.
• Use only a genuine NISSAN fuel filler cap as a replacement. If an incorrect fuel filler cap is used, the

“MI” may come on.

• For servicing “Evaporative Emission System” parts, refer to 

EC-76, "System Diagram"

.

PREPARATION

FL-3

< PREPARATION >

C

D

E

F

G

H

I

J

K

L

M

A

FL

N

P

O

PREPARATION

PREPARATION

Commercial Service Tool

INFOID:0000000003793247

Tool name

Description

Lock ring wrench

Removing and installing lock ring 

ZZA0122D