Nissan Teana J32. Manual - part 520

 

  Index      Nissan     Nissan Teana J32 (2008 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  518  519  520  521   ..

 

 

Nissan Teana J32. Manual - part 520

 

 

EXL-50

< COMPONENT DIAGNOSIS >

[XENON TYPE]

POWER SUPPLY AND GROUND CIRCUIT

POWER SUPPLY AND GROUND CIRCUIT

BCM (BODY CONTROL MODULE)

BCM (BODY CONTROL MODULE) : Diagnosis Procedure

INFOID:0000000003894263

1.

CHECK FUSE AND FUSIBLE LINK

Check that the following fuse and fusible link are not blown.

Is the fuse fusing?

YES

>> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is

blown.

NO

>> GO TO 2.

2.

CHECK POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect BCM connectors.

3.

Check voltage between BCM harness connector and ground.

Is the measurement value normal?

YES

>> GO TO 3.

NO

>> Repair harness or connector.

3.

CHECK GROUND CIRCUIT

Check continuity between BCM harness connector and ground.

Does continuity exist?

YES

>> INSPECTION END

NO

>> Repair harness or connector.

IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)

IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM) : Di-
agnosis Procedure

INFOID:0000000003894265

1.

CHECK FUSES AND FUSIBLE LINK

Check that the following IPDM E/R fuses or fusible links are not blown.

Signal name

Fuse and fusible link No.

Battery power supply

I

10

Terminals

Voltage

(Approx.)

(+)

(

)

BCM

Ground

Connector

Terminal

M118

1

Battery voltage

M119

11

BCM

Ground

Continuity

Connector

Terminal

M119

13

Existed

POWER SUPPLY AND GROUND CIRCUIT

EXL-51

< COMPONENT DIAGNOSIS >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Is the fuse fusing?

YES

>> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is

blown.

NO

>> GO TO 2.

2.

CHECK POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R connector.

3.

Check voltage between IPDM E/R harness connector and ground.

Is the measurement value normal?

YES

>> GO TO 3.

NO

>> Repair harness or connector.

3.

CHECK GROUND CIRCUIT

Check continuity between IPDM E/R harness connectors and ground.

Does continuity exist?

YES

>> INSPECTION END

NO

>> Repair harness or connector.

AUTO LEVELIZER CONTROL UNIT

AUTO LEVELIZER CONTROL UNIT : Diagnosis Procedure

INFOID:0000000003774348

1.

CHECK FUSES

Check that any of the following fuses are fusing

Is the fuse fusing?

YES

>> Repair the applicable circuit. And then replace the fuse.

NO

>> GO TO 2.

2.

CHECK POWER SUPPLY CIRCUIT

1.

Turn the ignition switch OFF.

2.

Disconnect auto levelizer control unit connector.

3.

Turn the ignition switch ON.

4.

Check voltage between auto levelizer control unit harness connector and ground.

Signal name

Fuses and fusible link No.

Battery power supply

E

50

51

Terminals

Voltage

(Approx.)

(+)

(

)

IPDM E/R

Connector

Terminal

Ground

E9

1

Battery voltage

IPDM E/R

Ground

Continuity

Connector

Terminal

E10

12

Existed

E11

41

Signal name

Location

Fuse No.

Capacity

Ignition power supply

Fuse block (J/B)

3

10A

EXL-52

< COMPONENT DIAGNOSIS >

[XENON TYPE]

POWER SUPPLY AND GROUND CIRCUIT

Is the measurement normal?

YES

>> GO TO 3.

NO

>> Repair the harnesses or connectors.

3.

CHECK GROUND CIRCUIT

Check continuity between auto levelizer control unit harness connector and ground.

Does continuity not exist?

YES

>> Power supply and ground circuit are normal.

NO

>> Repair the harnesses or connectors.

Terminals

Voltage

(Approx.)

(+)

(

)

Auto levelizer control unit

Ground

Connector

Terminal

C8

2

Battery voltage

Auto levelizer control unit

Ground

Continuity

Connector

Terminal

C8

1

Existed

EXTERIOR LAMP FUSE

EXL-53

< COMPONENT DIAGNOSIS >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

EXTERIOR LAMP FUSE

Description

INFOID:0000000003773554

Fuse list

Diagnosis Procedure

INFOID:0000000003773555

1.

CHECK FUSE

Check that the following fuses are not fusing.

Is the fuse fusing?

YES

>> Repair the applicable circuit. And then replace the fuse.

NO

>> The fuse is normal.

Unit

Location

Fuse No.

Capacity

Headlamp HI (LH) 

IPDM E/R

#54

10 A

Headlamp HI (RH) 

IPDM E/R

#55

10 A

Headlamp LO (LH) 

IPDM E/R

#56

15 A

Headlamp LO (RH) 

IPDM E/R

#57

15 A

Front fog lamp

IPDM E/R

#58

15 A

Parking lamp

IPDM E/R

#52

10 A

• Tail  lamp
• License plate lamp
• Each illumination

IPDM E/R

#53

10 A

Stop lamp

FUSE BLOCK (J/B)

#7

10 A

Back-up lamp

FUSE BLOCK (J/B)

#4

10 A

Unit

Location

Fuse No.

Capacity

Headlamp HI (LH) 

IPDM E/R

#54

10 A

Headlamp HI (RH) 

IPDM E/R

#55

10 A

Headlamp LO (LH) 

IPDM E/R

#56

15 A

Headlamp LO (RH) 

IPDM E/R

#57

15 A

Front fog lamp

IPDM E/R

#58

15 A

Parking lamp

IPDM E/R

#52

10 A

• Tail lamp
• License plate lamp
• Each illumination

IPDM E/R

#53

10 A

Stop lamp

FUSE 
BLOCK (J/B)

#7

10 A

Back-up lamp

FUSE 
BLOCK (J/B)

#4

10 A

 

 

 

 

 

 

 

Content   ..  518  519  520  521   ..