Nissan Teana J32. Manual - part 211

 

  Index      Nissan     Nissan Teana J32 (2008 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  209  210  211  212   ..

 

 

Nissan Teana J32. Manual - part 211

 

 

BCS-26

< FUNCTION DIAGNOSIS >

DIAGNOSIS SYSTEM (BCM)

SELF-DIAG RESULT

Refer to 

BCS-74, "DTC Index"

.

DATA MONITOR

INSIDE ANT DIAGNOSIS

This function allows inside key antenna self-diagnosis.

HORN WITH KEYLESS LOCK

Horn reminder function mode by Intelligent Key button can be changed to operate (ON) or not op-
erate (OFF) in this mode.

Monitor item

Description

Monitor Item

Condition

REQ SW -DR

Indicates [ON/OFF] condition of door request switch (driver side).

REQ SW -AS

Indicates [ON/OFF] condition of door request switch (passenger side).

REQ SW -BD/TR

Indicates [ON/OFF] condition of trunk lid opener request switch.

PUSH SW

Indicates [ON/OFF] condition of push-button ignition switch.

IGN RLY2 -F/B

Indicates [ON/OFF] condition of ignition relay 2.

CLUCH SW

NOTE:
This item is displayed, but cannot be monitored. 

BRAKE SW 1

Indicates [ON/OFF] condition of brake switch.

DETE/CANCL SW

Indicates [ON/OFF] condition of the P position.

SFT PN/N SW

Indicates [ON/OFF] condition of the P or N position.

S/L -LOCK

Indicates [ON/OFF] condition of steering lock unit (LOCK).

S/L -UNLOCK

Indicates [ON/OFF] condition of steering lock unit (UNLOCK).

S/L RELAY -F/B

Indicates [ON/OFF] condition of steering lock relay.

UNLK SEN -DR

Indicates [ON/OFF] condition of driver door UNLOCK status.

PUSH SW -IPDM

Indicates [ON/OFF] condition of push-button ignition switch.

IGN RLY1 -F/B

Indicates [ON/OFF] condition of ignition relay 1.

DETE SW -IPDM

Indicates [ON/OFF] condition of the P position.

SFT PN -IPDM

Indicates [ON/OFF] condition of the P or N position.

SFT P -MET

Indicates [ON/OFF] condition of the P position.

SFT N -MET

Indicates [ON/OFF] condition of the N position.

ENGINE STATE

Indicates [STOP/STALL/CRANK/RUN] condition of engine states.

S/L LOCK-IPDM

Indicates [ON/OFF] condition of steering lock unit (LOCK).

S/L UNLK-IPDM

Indicates [ON/OFF] condition of steering lock unit (UNLOCK).

S/L RELAY-REQ

Indicates [ON/OFF] condition of steering lock relay.

VEH SPEED 1

Displays the vehicle speed signal received from combination meter by numerical value [Km/h].

VEH SPEED 2

Displays the vehicle speed signal received from ABS, VDC or CVT by numerical value [Km/h].

DOOR STAT-DR

Indicates [LOCK/READY/UNLK] condition of driver side door status.

DOOR STAT-AS

Indicates [LOCK/READY/UNLK] condition of passenger side door status.

ID OK FLAG

Indicates [SET/RESET] condition of key ID.

PRMT ENG STRT

Indicates [SET/RESET] condition of engine start possibility.

PRMT RKE STRT

NOTE:
This item is displayed, but cannot be monitored. 

KEY SW -SLOT

Indicates [ON/OFF] condition of key slot.

TRNK/HAT MNTR

Indicates [ON/OFF] condition of trunk lid.

RKE-LOCK

Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.

RKE-UNLOCK

Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.

RKE-TR/BD

Indicates [ON/OFF] condition of TRUNK OPEN signal from Intelligent Key. 

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-27

< FUNCTION DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

ACTIVE TEST

RKE-PANIC

NOTE:
This item is displayed, but cannot be monitored. 

RKE-P/W OPEN

NOTE:
This item is displayed, but cannot be monitored. 

RKE-MODE CHG

Indicates [ON/OFF] condition of MODE CHANGE signal from Intelligent Key.

RKE OPE COUN1

When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the 
numerical values start changing.

RKE OPE COUN2

NOTE:
This item is displayed, but cannot be monitored. 

Monitor Item

Condition

Test item

Description

BATTERY SAVER

This test is able to check interior room lamp operation.
The interior room lamp will be activated when “ON” on CONSULT-III screen is touched.

PW REMOTO DOWN SET

NOTE:
This item is displayed, but cannot be used. 

OUTSIDE BUZZER

This test is able to check Intelligent Key warning buzzer operation.
The Intelligent Key warning buzzer will be activated when “ON” on CONSULT-III screen is touched.

INSIDE BUZZER

This test is able to check warning chime in combination meter operation.
• Take away warning chime sounds when “TAKE OUT” on CONSULT-III screen is touched.
• Key warning chime sounds when “KEY” on CONSULT-III screen is touched.
• P position warning chime sounds when “KNOB” on CONSULT-III screen is touched.

INDICATOR

This test is able to check warning lamp operation.
• “KEY” Warning lamp illuminates when “RED ON” on CONSULT-III screen is touched.
• “KEY” Warning lamp blinks when “RED IND” on CONSULT-III screen is touched.

INT LAMP

This test is able to check interior room lamp operation.
The interior room lamp will be activated when “ON” on CONSULT-III screen is touched.

LCD

This test is able to check meter display information
• Engine start information displays when “BP N” on CONSULT-III screen is touched.
• Engine start information displays when “BP I” on CONSULT-III screen is touched.
• Key ID warning displays when “ID NG” on CONSULT-III screen is touched.
• Steering lock information displays when “ROTAT” on CONSULT-III screen is touched.
• P position warning displays when “SFT P” on CONSULT-III screen is touched.
• Intelligent Key insert information displays when “INSRT” on CONSULT-III screen is touched.
• Intelligent Key low battery warning displays when “BATT” on CONSULT-III screen is touched.
• Take away warning displays when “OUTKEY” on CONSULT-III screen is touched.
• OFF position warning displays when “LK WN” on CONSULT-III screen is touched.

TRUNK/GLASS HATCH

This test is able to check trunk lid opener actuator open operation.
This actuator opens when “OPEN” on CONSULT-III screen is touched.

FLASHER

This test is able to check security hazard lamp operation.
The hazard lamps will be activated when “RH” or “LH”on CONSULT-III screen is touched.

HORN

This test is able to check horn operation.
The horn will be activated when “ON” on CONSULT-III screen is touched.

P RANGE

This test is able to check control device power supply
Control device power is supplied when “ON” on CONSULT-III screen is touched.

ENGINE SW ILLUMI

This test is able to check push-ignition switch illumination operation.
Push-ignition switch illumination illuminates when “ON” on CONSULT-III screen is touched.

LOCK INDICATOR

This test is able to check LOCK indicator in push-ignition switch operation.
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.

ACC INDICATOR

This test is able to check ACC indicator in push-ignition switch operation.
ACC indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.

IGNITION ON IND

This test is able to check ON indicator in push-ignition switch operation.
ON indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.

BCS-28

< FUNCTION DIAGNOSIS >

DIAGNOSIS SYSTEM (BCM)

COMB SW

COMB SW : CONSULT-III Function (BCM - COMB SW)

INFOID:0000000003809604

DATA MONITOR

BCM

BCM : CONSULT-III Function (BCM - BCM)

INFOID:0000000003809605

WORK SUPPORT

NOTE:

KEY SLOT ILLUMI

This test is able to check key slot illumination operation.
Key slot illumination illuminates when “ON” on CONSULT-III screen is touched.

TRUNK/BACK DOOR

This test is able to check trunk lid opener actuator open operation.
This actuator opens when “OPEN” on CONSULT-III screen is touched.

Test item

Description

Monitor item [UNIT]

Description

FR WIPER HI
[Off/On]

Displays the status of the FR WIPER HI switch in combination switch judged by BCM with the combination 
switch reading function.

FR WIPER LOW
[Off/On]

Displays the status of the FR WIPER LOW switch in combination switch judged by BCM with the combination 
switch reading function.

FR WASHER SW
[Off/On]

Displays the status of the FR WASHER switch in combination switch judged by BCM with the combination 
switch reading function.

FR WIPER INT
[Off/On]

Displays the status of the FR WIPER INT switch in combination switch judged by BCM with the combination 
switch reading function.

FR WIPER STOP
[Off/On]

Displays the status of the front wiper stop position signal received from IPDM E/R via CAN communication.

INT VOLUME
[1 - 7]

Displays the status of wiper intermittent dial position judged by BCM with the combination switch reading 
function.

TURN SIGNAL R
[Off/On]

Displays the status of the TURN RH switch in combination switch judged by BCM with the combination switch 
reading function.

TURN SIGNAL L
[Off/On]

Displays the status of the TURN LH switch in combination switch judged by BCM with the combination switch 
reading function.

TAIL LAMP SW
[Off/On]

Displays the status of the TAIL LAMP switch in combination switch judged by BCM with the combination 
switch reading function.

HI BEAM SW
[Off/On]

Displays the status of the HI BEAM switch in combination switch judged by BCM with the combination switch 
reading function.

HEAD LAMP SW 1
[Off/On]

Displays the status of the HEADLAMP 1 switch in combination switch judged by BCM with the combination 
switch reading function.

HEAD LAMP SW 2
[Off/On]

Displays the status of the HEADLAMP 2 switch in combination switch judged by BCM with the combination 
switch reading function.

PASSING SW
[Off/On]

Displays the status of the PASSING switch in combination switch judged by BCM with the combination switch 
reading function.

AUTO LIGHT SW
[Off/On]

Displays the status of the AUTO LIGHT switch in combination switch judged by BCM with the combination 
switch reading function.

FR FOG SW
[Off/On]

Displays the status of the FR FOG switch in combination switch judged by BCM with the combination switch 
reading function.

RR FOG SW
[Off/On]

Displays the status of the RR FOG switch in combination switch judged by BCM with the combination switch 
reading function.

Item

Description

RESET SETTING VALUE

Return a value set with Work Support of each system to a default value in factory shipment.

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-29

< FUNCTION DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

When performed “RESET SETTING VALUE” on “Work Support (BCM - BCM)”, set “WIPER SPEED SETTING” on “Work Support (BCM
- WIPER)” to “On”.

IMMU

IMMU : CONSULT-III Function (BCM - IMMU)

INFOID:0000000003897057

APPLICATION ITEM

CONSULT-III performs the following functions via CAN communication with BCM.

DATA MONITOR

ACTIVE TEST

BATTERY SAVER

BATTERY SAVER : CONSULT-III Function (BCM - BATTERY SAVER)

INFOID:0000000003897060

WORK SUPPORT

*: Factory setting

DATA MONITOR

Diagnosis mode

Function Description

DATA MONITOR

The BCM input/output signals are displayed.

ACTIVE TEST

The signals used to activate each device are forcibly supplied from BCM.

Monitor item 

Content

CONFRM ID ALL

Indicates [YET] at all time.
Switches to [DONE] when a registered Intelligent Key is inserted into the key slot.

CONFIRM ID4

CONFIRM ID3

CONFIRM ID2

CONFIRM ID1

TP 4

Indicates the number of ID which has been registered.

TP 3

TP 2

TP 1

PUSH SW

Indicates [ON/OFF] condition of push-button ignition switch.

KEY SW -SLOT

Indicates [ON/OFF] condition of key slot.

Test item

Description

THEFT IND

This test is able to check security indicator lamp operation.
The lamp will be turned on when “ON” on CONSULT-III screen touched.

Service item

Setting item

Setting

BATTERY SAVER SET

On*

With the exterior lamp battery saver function

Off

Without the exterior lamp battery saver function

ROOM LAMP BAT SAV SET

On*

With the interior room lamp battery saver function

Off

Without the interior room lamp battery saver function

ROOM LAMP TIMER SET

MODE 1*

30 min.

Sets the interior room lamp battery saver timer operating 
time. 

MODE 2

60 min.

 

 

 

 

 

 

 

Content   ..  209  210  211  212   ..