Nissan Teana J32. Manual - part 1259

POWER SUPPLY AND GROUND CIRCUIT

WW-21

< COMPONENT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

POWER SUPPLY AND GROUND CIRCUIT

BCM (BODY CONTROL MODULE)

BCM (BODY CONTROL MODULE) : Diagnosis Procedure

INFOID:0000000003941294

1.

CHECK FUSE AND FUSIBLE LINK

Check that the following fuse and fusible link are not blown.

Is the fuse fusing?

YES

>> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is

blown.

NO

>> GO TO 2.

2.

CHECK POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect BCM connectors.

3.

Check voltage between BCM harness connector and ground.

Is the measurement value normal?

YES

>> GO TO 3.

NO

>> Repair harness or connector.

3.

CHECK GROUND CIRCUIT

Check continuity between BCM harness connector and ground.

Does continuity exist?

YES

>> INSPECTION END

NO

>> Repair harness or connector.

IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)

IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM) : Di-
agnosis Procedure

INFOID:0000000003941295

1.

CHECK FUSES AND FUSIBLE LINK

Check that the following IPDM E/R fuses or fusible links are not blown.

Signal name

Fuse and fusible link No.

Battery power supply

I

10

Terminals

Voltage

(Approx.)

(+)

(

−

)

BCM

Ground

Connector

Terminal

M118

1

Battery voltage

M119

11

BCM

Ground

Continuity

Connector

Terminal

M119

13

Existed

WW-22

< COMPONENT DIAGNOSIS >

POWER SUPPLY AND GROUND CIRCUIT

Is the fuse fusing?

YES

>> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is

blown.

NO

>> GO TO 2.

2.

CHECK POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R connector.

3.

Check voltage between IPDM E/R harness connector and ground.

Is the measurement value normal?

YES

>> GO TO 3.

NO

>> Repair harness or connector.

3.

CHECK GROUND CIRCUIT

Check continuity between IPDM E/R harness connectors and ground.

Does continuity exist?

YES

>> INSPECTION END

NO

>> Repair harness or connector.

Signal name

Fuses and fusible link No.

Battery power supply

E

50

51

Terminals

Voltage

(Approx.)

(+)

(

−

)

IPDM E/R

Connector

Terminal

Ground

E9

1

Battery voltage

IPDM E/R

Ground

Continuity

Connector

Terminal

E10

12

Existed

E11

41

FRONT WIPER MOTOR LO CIRCUIT

WW-23

< COMPONENT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

FRONT WIPER MOTOR LO CIRCUIT

Component Function Check

INFOID:0000000003761586

1.

CHECK FRONT WIPER LO OPERATION

IPDM E/R AUTO ACTIVE TEST

1.

Start IPDM E/R auto active test. Refer to 

PCS-11, "Diagnosis Description"

.

2.

Check that the front wiper operates at the LO operation.

CONSULT-III ACTIVE TEST

1.

Select “FRONT WIPER” of IPDM E/R active test item.

2.

With operating the test item, check front wiper operation.

Is front wiper (LO) operation normally?

YES

>> Front wiper motor LO circuit is normal.

NO

>> Refer to 

WW-23, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000003761587

1.

CHECK FRONT WIPER MOTOR (LO) OUTPUT VOLTAGE

CONSULT-III ACTIVE TEST

1.

Turn the ignition switch OFF.

2.

Disconnect front wiper motor connector.

3.

Turn the ignition switch ON.

4.

Select “FRONT WIPER” of IPDM E/R active test item.

5.

With operating the test item, check voltage between IPDM E/R harness connector and ground.

Is the measurement value normal?

YES

>> GO TO 2.

NO

>> Replace IPDM E/R.

2.

CHECK FRONT WIPER MOTOR (LO) OPEN CIRCUIT

1.

Turn the ignition switch OFF.

2.

Disconnect IPDM E/R connector.

3.

Check continuity between IPDM E/R harness connector and front wiper motor harness connector.

Does continuity exist?

YES

>> GO TO 3.

NO

>> Repair the harness or connector.

3.

CHECK FRONT WIPER MOTOR (LO) SHORT CIRCUIT

Check continuity between IPDM E/R harness connector and ground.

Lo

: Front wiper (LO) operation

Off

: Stop the front wiper.

Terminals

Test item

Voltage (Approx.)

(+)

(

−

)

IPDM E/R

Ground

FRONT WIPER

Connector

Terminal

E10

4

Lo

Battery voltage

Off

0 V

IPDM E/R

Front wiper motor

Continuity

Connector

Terminal

Connector

Terminal

E10

4

E12

3

Existed

WW-24

< COMPONENT DIAGNOSIS >

FRONT WIPER MOTOR LO CIRCUIT

Does continuity exist?

YES

>> Repair the harness or connector.

NO

>> Replace front wiper motor.

IPDM E/R

Ground

Continuity

Connector

Terminal

E10

4

Not existed