Nissan Teana J32. Manual - part 1174

 

  Index      Nissan     Nissan Teana J32 (2008 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1172  1173  1174  1175   ..

 

 

Nissan Teana J32. Manual - part 1174

 

 

TM-220

< COMPONENT DIAGNOSIS >

[CVT: RE0F10A]

P0715 INPUT SPEED SENSOR (PRI SPEED SENSOR)

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace damaged parts.

5.

CHECK HARNESS BETWEEN TCM AND INPUT SPEED SENSOR (PRIMARY SPEED SENSOR) (PART

2)

Check continuity between TCM vehicle side harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 10.

NO

>> Repair or replace damaged parts.

6.

CHECK HARNESS BETWEEN IPDM E/R AND INPUT SPEED SENSOR (PRIMARY SPEED SENSOR)

(POWER) (PART 1)

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R connector.

3.

Check continuity between IPDM E/R vehicle side harness connector terminal and input speed sensor (pri-
mary speed sensor) vehicle side harness connector terminal.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace damaged parts.

7.

CHECK HARNESS BETWEEN IPDM E/R AND INPUT SPEED SENSOR (PRIMARY SPEED SENSOR)

(POWER) (PART 2)

Check continuity between IPDM E/R vehicle side harness connector terminal and ground.

Is the inspection result normal?

YES

>>

Check the following.

• Harness for short or open between ignition switch and IPDM E/R
• 10 A fuse (No. 43, located in the IPDM E/R)
• Ignition switch

NO

>> Repair or replace damaged parts.

8.

CHECK HARNESS BETWEEN TCM AND INPUT SPEED SENSOR (PRIMARY SPEED SENSOR) (SEN-

SOR GROUND) (PART 1)

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector.

3.

Check continuity between TCM vehicle side harness connector terminal and input speed sensor (primary
speed sensor) vehicle side harness connector terminal.

TCM vehicle side harness connector

Input speed sensor (primary speed sensor) vehicle 

side harness connector

Continuity

Connector

Terminal

Connector

Terminal

F23

33

F55

2

Existed

TCM vehicle side harness connector

Ground

Continuity

Connector

Terminal

F23

33

Not existed

IPDM E/R vehicle side harness connector

Input speed sensor (primary speed sensor) vehicle 

side harness connector

Continuity

Connector

Terminal

Connector

Terminal

F12

58

F55

3

Existed

IPDM E/R vehicle side harness connector

Ground

Continuity

Connector

Terminal

F12

58

Not existed

P0715 INPUT SPEED SENSOR (PRI SPEED SENSOR)

TM-221

< COMPONENT DIAGNOSIS >

[CVT: RE0F10A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Is the inspection result normal?

YES

>> GO TO 9.

NO

>> Repair or replace damaged parts.

9.

CHECK HARNESS BETWEEN TCM AND INPUT SPEED SENSOR (PRIMARY SPEED SENSOR) (SEN-

SOR GROUND) (PART 2)

1.

Disconnect CVT unit connector.

2.

Check continuity between TCM vehicle side harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 10.

NO

>> Repair or replace damaged parts.

10.

CHECK CVT UNIT CIRCUIT

Check continuity between CVT unit connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 11.

NO

>> Repair or replace damaged parts.

11.

CHECK TCM

1.

Replace with the same type of TCM. Refer to 

TM-315, "Exploded View"

.

2.

Connect each connector.

3.

Perform “DTC CONFIRMATION PROCEDURE”. Refer to 

TM-218, "DTC Logic"

.

Is “P0715 INPUT SPD SEN/CIRC” detected?

YES

>> Replace input speed sensor (primary speed sensor). Refer to 

TM-323, "Exploded View"

.

NO

>> Replace TCM. Refer to 

TM-315, "Exploded View"

.

12.

DETECT MALFUNCTIONING ITEMS

Check TCM connector pin terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES

>> Replace TCM. Refer to 

TM-315, "Exploded View"

.

NO

>> Repair or replace damaged parts.

TCM vehicle side harness connector

Input speed sensor (primary speed sensor) vehicle 

side harness connector

Continuity

Connector

Terminal

Connector

Terminal

F23

25

F55

1

Existed

TCM vehicle side harness connector

Ground

Continuity

Connector

Terminal

F23

25

Not existed

CVT unit connector

Ground

Continuity

Connector

Terminal

F24

19

Not existed

TM-222

< COMPONENT DIAGNOSIS >

[CVT: RE0F10A]

P0720 VEHICLE SPEED SENSOR CVT (SECONDARY SPEED SENSOR)

P0720 VEHICLE SPEED SENSOR CVT (SECONDARY SPEED SENSOR)

Description

INFOID:0000000003806397

The vehicle speed sensor CVT [output speed sensor (secondary speed sensor)] detects the revolution of the
CVT output shaft and emits a pulse signal. The pulse signal is transmitted to the TCM, which converts it into
vehicle speed.

DTC Logic

INFOID:0000000003806398

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Always drive vehicle at a safe speed.
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF. Then wait at least 10 seconds before performing the next test.
Perform the following procedure to confirm the malfunction is eliminated after the repair.

1.

CHECK DTC DETECTION

With CONSULT-III

1.

Turn ignition switch ON.

2.

Select “Data Monitor” mode for “TRANSMISSION”.

3.

Start engine and maintain the following conditions for at least 12 consecutive seconds.

With GST

Follow the procedure “With CONSULT-III”.

Is “P0720 VEH SPD SEN/CIR AT” detected?

YES

>> Go to 

TM-222, "Diagnosis Procedure"

.

NO

>> Check intermittent incident. Refer to 

GI-35, "Intermittent Incident"

.

Diagnosis Procedure

INFOID:0000000003806399

1.

CHECK OUTPUT SPEED SENSOR (SECONDARY SPEED SENSOR)

With CONSULT-III

1.

Start engine.

2.

Check voltage between TCM connector terminals.

DTC

Item

(CONSULT-III screen term)

Malfunction is detected when...

Possible cause

P0720

VEH SPD SEN/CIR AT

• Signal from vehicle speed 

sensor CVT [output speed 
sensor (secondary speed 
sensor)] is not input due to 
open or short circuit.

• Unexpected signal is input 

during running.

• Harness or connectors

(Sensor circuit is open or 
shorted.)

• Output speed sensor (sec-

ondary speed sensor)

ACC PEDAL OPEN

: More than 1.0/8

RANGE

: “D” position

Driving location

: Driving the vehicle uphill (increased engine load) will help maintain the 
driving conditions required for this test.

P0720 VEHICLE SPEED SENSOR CVT (SECONDARY SPEED SENSOR)

TM-223

< COMPONENT DIAGNOSIS >

[CVT: RE0F10A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

3.

If OK, check pulse when vehicle drive.

Is the inspection result normal?

YES

>> GO TO 11.

NO

>> GO TO 2.

2.

CHECK POWER AND SENSOR GROUND

1.

Turn ignition switch OFF.

2.

Disconnect output speed sensor (secondary speed sensor) connector.

3.

Turn ignition switch ON.

4.

Check voltage between output speed sensor (secondary speed sensor) vehicle side harness connector
terminals.

5.

Check voltage between output speed sensor (secondary speed sensor) vehicle side harness connector
terminal and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO-1 (Battery voltage is not supplied between terminals 1 and 3, and between terminal 3 and ground)>>GO

TO 6.

NO-2 (Battery voltage is not supplied between terminals 1 and 3 only)>>GO TO 8.

3.

CHECK HARNESS BETWEEN TCM AND OUTPUT SPEED SENSOR (SECONDARY SPEED SENSOR)

(SENSOR GROUND)

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector.

3.

Check continuity between TCM vehicle side harness connector terminal and ground.

Is the inspection result normal?

TCM connector

Voltage (Approx.)

Connector

Terminal

(+)

(

)

F23

46

7

Battery voltage

48

TCM connector

Condition

Data (Approx.)

Connector

Terminal

F23

34

When driving at 20 km/h (12 
MPH) in “D” position, use the 
CONSULT-III pulse frequency 
measuring function.

490 Hz

Output speed sensor (secondary speed sensor) vehicle side harness connector

Voltage (Approx.)

Connector

Terminal

(+)

(

)

F19

3

1

Battery voltage

Output speed sensor (secondary speed sensor) vehicle side har-

ness connector

Ground

Voltage (Approx.)

Connector

Terminal

F19

3

Battery voltage

TCM vehicle side harness connector

Ground

Continuity

Connector

Terminal

F23

7

Not existed

 

 

 

 

 

 

 

Content   ..  1172  1173  1174  1175   ..