Nissan Teana J32. Manual - part 3

DIAGNOSIS AND REPAIR WORKFLOW

ADP-5

< BASIC INSPECTION >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

1.

GET INFORMATION FOR SYMPTOM

Get detailed information from the customer about the symptom (the condition and the environment when the
incident/malfunction occurs).

>> GO TO 2.

2.

CHECK DTC WITH AUTOMATIC DRIVE POSITIONER SYSTEM

Check “Self Diagnostic Result” with CONSULT-III. Refer to 

ADP-124, "DTC Index"

Are any symptoms described and any DTC displayed?

Symptom is described, DTC is detected.>>GO TO 3.
Symptom is not described, DTC is detected.>>GO TO 6.
Symptom is described, DTC is not detected.>>GO TO 4.

3.

CONFIRM THE SYMPTOM

Try to confirm the symptom described by the customer.

>> GO TO 6.

4.

CONFIRM THE SYMPTOM

Try to confirm the symptom described by the customer.

>> GO TO 5.

5.

CHECK NORMAL OPERATING CONDITION

Check normal operating condition. Refer to 

ADP-134, "Description"

.

Is the incident a normal operation?

YES

>> GO TO 10.

NO

>> GO TO 7.

6.

PERFORM DTC CONFIRMATION PROCEDURE

Perform the confirmation procedure for the detected DTC.

Is the DTC displayed?

YES

>> GO TO 8.

NO

>> Check intermittent incident. Refer to 

GI-35, "Intermittent Incident"

.

7.

PERFORM COMPONENT FUNCTION CHECK 

Perform the component function check for the isolated malfunctioning point.

>> GO TO 8.

8.

DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE

Isolate the malfunctioning point by performing the diagnosis procedure relevant to the symptom during the
component diagnosis.

>> GO TO 9.

9.

REPARE OR REPLACE

Repair or replace the malfunctioning part.

>> GO TO 10.

10.

FINAL CHECK

Perform the DTC confirmation procedure (if DTC is detected) or component function check (if no DTC is
detected) again. Check that the malfunction is repaired.

Are all malfunctions repaired?

ADP-6

< BASIC INSPECTION >

DIAGNOSIS AND REPAIR WORKFLOW

YES

>> INSPECTION END

Symptom is detected.>> GO TO 5.
DTC is detected.>> GO TO 6.

INSPECTION AND ADJUSTMENT

ADP-7

< BASIC INSPECTION >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

INSPECTION AND ADJUSTMENT

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : De-
scription

INFOID:0000000003759058

Each function is reset to the following condition when the battery terminal is disconnected.

*1

: Default value is 40mm.

NOTE:
Notice that disconnecting the battery when detected DTC are present will erase the DTC memory.

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Spe-
cial Repair Requirement

INFOID:0000000003759059

1.

SYSTEM INITIALIZATION

Perform system initialization. Refer to 

ADP-8, "SYSTEM INITIALIZATION : Description"

.

>> GO TO 2.

2.

SYSTEM SETTING

Perform system setting. Refer to 

ADP-9, "SYSTEM SETTING : Description"

.

>> GO TO 3.

3.

MEMORY STORAGE

Perform memory storage. Refer to 

ADP-8, "MEMORY STORING : Description"

.

>> END

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description

INFOID:0000000003759060

Each function is reset to the following condition when the driver seat control unit is replaced.

*1

: Default value is 40 mm.

NOTE:
Notice that disconnecting the battery when detected DTC are present will erase the DTC memory.

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-

Function

Condition

Procedure

Memory (Seat)

Erased

Perform memory storage

Entry/exit assist

OFF

Perform system initialization

Set slide amount

*1

Intelligent Key interlock

Erased

Perform system initialization

Perform memory storage

Function

Condition

Procedure

Memory (Seat)

Erased

Perform memory storage

Entry/exit assist

OFF

Perform system initialization

Set slide amount

*1

Intelligent Key interlock

Erased

Perform system initialization

Perform memory storage

ADP-8

< BASIC INSPECTION >

INSPECTION AND ADJUSTMENT

quirement

INFOID:0000000003759061

1.

SYSTEM INITIALIZATION

Perform system initialization. Refer to 

ADP-8, "SYSTEM INITIALIZATION : Description"

.

>> GO TO 2.

2.

SYSTEM SETTING

Perform system setting. Refer to 

ADP-9, "SYSTEM SETTING : Description"

.

>> GO TO 3.

3.

MEMORY STORAGE

Perform memory storage. Refer to 

ADP-8, "MEMORY STORING : Description"

.

>> END

SYSTEM INITIALIZATION

SYSTEM INITIALIZATION : Description

INFOID:0000000003759062

Always perform the initialization when the battery terminal is disconnected or the driver seat control unit is
replaced.
The entry/exit assist function will not operate normally unless initialization is performed. 

SYSTEM INITIALIZATION : Special Repair Requirement

INFOID:0000000003759063

INITIALIZATION PROCEDURE

1.

 CHOOSE METHOD

There are two initialization methods.

Which method do you use?

With door switch>>GO TO 2.
With vehicle speed>>GO TO 4.

2.

 STEP A-1

Turn ignition switch from the ACC to the OFF position. 

>> GO TO 3.

3.

 STEP A-2

Driver door switch is ON (open) 

→

 OFF (close) 

→

 ON (open).

>> END

4.

 STEP B-1

Drive the vehicle at more than 25 km/h (16 MPH). 

>> END

MEMORY STORING

MEMORY STORING : Description

INFOID:0000000003759064

Always perform memory storage when the battery terminal is disconnected or the driver seat control unit is
replaced. The memory function and Intelligent Key interlock function will not operate normally unless memory
storage is performed.