Nissan Murano Z51. Manual - part 489

DLN-90

< PREPARATION >

[REAR FINAL DRIVE: R145]

PREPARATION

PREPARATION

PREPARATION

Special Service Tools

INFOID:0000000005514247

The actual shapes of Kent-More tools may differ from those of special service tools illustrated here.

Tool number
(Kent-More No.)
Tool name

Description

KV38100200
(J-26233)
Drift
a: 65 mm (2.56 in) dia.
b: 49 mm (1.93 in) dia.

• Installing front oil seal
• Installing side oil seal

ST27861000
(

—

)

Drift
a: 62 mm (2.44 in) dia.
b: 52 mm (2.05 in) dia.

Installing front oil seal

ST35271000
(J-26091)
Drift
a: 72 mm (2.83 in) dia.
b: 63 mm (2.48 in) dia.

Installing center oil seal

KV40100610
(J-26089)
Drift
a: 63 mm (2.48 in) dia.
b: 54.3 mm (2.138 in) dia.

Removing and installing gear carrier and rear 
cover (2 pieces are used)

ST33052000
(

—

)

Drift
a: 22 mm (0.87 in) dia.
b: 28 mm (1.10 in) dia.

Removing side bearing inner race

KV4010520
(

—

)

Drift
a: 39.7 mm (1.563 in) dia.
b: 35 mm (1.38 in) dia.
c: 15 mm (0.59 in) dia.

Installing side bearing inner race

ZZA1143D

ZZA0832D

ZZA0814D

ZZA1000D

ZZA1023D

ZZA1133D

PREPARATION

DLN-91

< PREPARATION >

[REAR FINAL DRIVE: R145]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

KV38108500
(

—

)

Drive pinion socket

• Removing and installing drive pinion nut
• Measuring preload torque

KV38108400
(

—

)

Pinion nut wrench

Removing and installing drive pinion nut

ST17130000
(

—

)

Drift
a: 31.8 mm (1.252 in) dia.
b: 58 mm (2.28 in) dia.

Installing pinion rear bearing outer race

ST33230000
(J-25805-01)
Drift
a: 51 mm (2.01 in) dia.
b: 41 mm (1.61 in) dia.
c: 28.5 mm (1.122 in) dia.

Installing pinion front bearing outer race

ST23860000
(

—

)

Drift
a: 38 mm (1.50 in) dia.
b: 33 mm (1.30 in) dia.

• Installing pinion rear bearing inner race
• Installing pinion front bearing inner race

ST38220000
(

—

)

Press stand
a: 63 mm (2.48 in) dia.
b: 65 mm (2.56 in) dia.

Installing pinion front bearing inner race

Tool number
(Kent-More No.)
Tool name

Description

ZZA1205D

ZZA1206D

ZZA0836D

ZZA1046D

ZZA0534D

ZZA1058D

DLN-92

< PREPARATION >

[REAR FINAL DRIVE: R145]

PREPARATION

Commercial Service Tools

INFOID:0000000005514248

ST3127S000
(J-25765-A)
Preload gauge

Measuring preload torque

KV381086S1
(

—

)

Dummy cover set
1. KV38108610
(

—

)

Dummy cover
2. KV38108621
(

—

)

Dummy cover spacer
3. KV38108630
(

—

)

Dummy cover shim

• Checking backlash
• Checking drive gear runout
• Checking tooth contact

Tool number
(Kent-More No.)
Tool name

Description

ZZA0503D

SDIA2313E

Tool name

Description

Flange wrench

Removing and installing companion flange 
lock nut

Power tool

Loosening bolts and nuts

NT771

PBIC0190E

REAR DIFFERENTIAL GEAR OIL

DLN-93

< PERIODIC MAINTENANCE >

[REAR FINAL DRIVE: R145]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

PERIODIC MAINTENANCE

REAR DIFFERENTIAL GEAR OIL

Inspection

INFOID:0000000005514249

OIL LEAKAGE

Check that oil is not leaking from final drive assembly or around it.

OIL LEVEL

• Remove filler plug (1) and check oil level from filler plug mounting

hole as shown in the figure.

CAUTION:

Never start engine while checking oil level.

• Set a new gasket on filler plug and install it on final drive assembly.

Refer to 

DLN-104, "Exploded View"

.

CAUTION:

Never reuse gasket.

Draining

INFOID:0000000005514250

1.

Stop engine.

2.

Remove drain plug (1) and drain gear oil.

3.

Set a new gasket on drain plug and install it to final drive assem-
bly and tighten to the specified torque. Refer to 

DLN-104,

"Exploded View"

.

CAUTION:

Never reuse gasket.

Refilling

INFOID:0000000005514251

1.

Remove filler plug (1). Fill with new gear oil until oil level reaches
the specified level near filler plug mounting hole.

2.

After refilling oil, check oil level. Set a new gasket to filler plug, then install it to final drive assembly. Refer
to 

DLN-104, "Exploded View"

.

CAUTION:

Never reuse gasket.

JPDID0164ZZ

JPDID0163ZZ

Oil grade and viscosity

: Refer to 

MA-15, "FOR 

NORTH AMERICA : Fluids 
and Lubricants"

 (for 

NORTH AMERICA), 

MA-16, 

"FOR MEXICO : Fluids and 
Lubricants"

 (for MEXICO).

Oil capacity

: Refer to 

DLN-126, "Gen-

eral Specification"

.

JPDID0164ZZ