Nissan Murano Z51. Manual - part 265

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-27

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

SELF-DIAG RESULT

Refer to 

BCS-90, "DTC Index"

.

DATA MONITOR

TRUNK/GLASS HATCH OPEN

Buzzer reminder function mode by back door request switch can be changed to operate (ON) or 
not operate (OFF) with this mode.

PANIC ALARM SET

Panic alarm button pressing time on Intelligent Key remote control button can be selected from the 
following with this mode. 
• MODE 1: 0.5 sec.
• MODE 2: Non-operation
• MODE 3: 1.5 sec.

PW DOWN SET

Unlock button pressing time on Intelligent Key button can be selected from the following with this 
mode. 
• MODE 1: 3 sec.
• MODE 2: Non-operation
• MODE 3: 5 sec.

TRUNK OPEN DELAY

NOTE:
This item is displayed, but cannot be supported. 

LO- BATT OF KEY FOB WARN

Intelligent Key low battery warning mode can be changed to operate (ON) or not operate (OFF) 
with this mode. 

ANTI KEY LOCK IN FUNCTI

Key reminder function mode can be changed to operate (ON) or not operate (OFF) with this mode.

HAZARD ANSWER BACK

Hazard reminder function mode can be selected from the following with this mode.
• LOCK ONLY: Door lock operation only
• UNLOCK ONLY: Door unlock operation only
• LOCK/UNLOCK: Lock/unlock operation
• OFF: Non-operation

ANS BACK I-KEY LOCK

Buzzer reminder function (lock operation) mode by door request switch (driver side and passenger 
side) can be selected from the following with this mode. 
• Horn chirp: Sound horn
• Buzzer: Sound Intelligent Key warning buzzer
• OFF: Non-operation

ANS BACK I-KEY UNLOCK

Buzzer reminder function (unlock operation) mode by door request switch can be changed to op-
erate (ON) or not operate (OFF) with this mode.

SHORT CRANKING OUTPUT

Starter motor can operate during the times below.
• 70  msec
• 100 msec
• 200 msec

INSIDE ANT DIAGNOSIS

This function allows inside key antenna self-diagnosis.

HORN WITH KEYLESS LOCK

Horn reminder function mode by Intelligent Key button can be changed to operate (ON) or not op-
erate (OFF) with this mode.

Monitor item

Description

Monitor Item

Condition

REQ SW -DR

Indicates [ON/OFF] condition of door request switch (driver side).

REQ SW -AS

Indicates [ON/OFF] condition of door request switch (passenger side).

REQ SW -RR

NOTE:
This item is displayed, but cannot be monitored. 

REQ SW -RL

NOTE:
This item is displayed, but cannot be monitored. 

REQ SW -BD/TR

Indicates [ON/OFF] condition of back door request switch.

PUSH SW

Indicates [ON/OFF] condition of push-button ignition switch.

IGN RLY2 -F/B

Indicates [ON/OFF] condition of ignition relay 2.

ACC RLY-FB

NOTE:
This item is displayed, but cannot be monitored. 

BCS-28

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM)

CLUCH SW

NOTE:
This item is displayed, but cannot be monitored. 

BRAKE SW 1

Indicates [ON/OFF]* condition of brake switch power supply.

BRAKE SW 2

Indicates [ON/OFF] condition of brake switch.

DETE/CANCL SW

Indicates [ON/OFF] condition of P position.

SFT PN/N SW

Indicates [ON/OFF] condition of P or N position.

S/L -LOCK

Indicates [ON/OFF] condition of steering lock unit (LOCK).
NOTE:
For models without steering lock unit this item is not displayed.

S/L -UNLOCK

Indicates [ON/OFF] condition of steering lock unit (UNLOCK).
NOTE:
For models without steering lock unit this item is not displayed.

S/L RELAY -F/B

Indicates [ON/OFF] condition of ignition switch.
NOTE:
For models without steering lock unit this item is not displayed.

UNLK SEN -DR

Indicates [ON/OFF] condition of driver door UNLOCK status.

PUSH SW -IPDM

Indicates [ON/OFF] condition of push-button ignition switch.

IGN RLY1 -F/B

Indicates [ON/OFF] condition of ignition relay 1.

DETE SW -IPDM

Indicates [ON/OFF] condition of P position.

SFT PN -IPDM

Indicates [ON/OFF] condition of P or N position.

SFT P -MET

Indicates [ON/OFF] condition of P position.

SFT N -MET

Indicates [ON/OFF] condition of N position.

ENGINE STATE

Indicates [STOP/START/CRANK/RUN] condition of engine states.

S/L LOCK-IPDM

Indicates [ON/OFF] condition of steering lock unit (LOCK).
NOTE:
For models without steering lock unit this item is not displayed.

S/L UNLK-IPDM

Indicates [ON/OFF] condition of steering lock unit (UNLOCK).
NOTE:
For models without steering lock unit this item is not displayed.

S/L RELAY-REQ

Indicates [ON/OFF] condition of steering lock relay.
NOTE:
For models without steering lock unit this item is not displayed.

VEH SPEED 1

Display the vehicle speed signal received from combination meter by numerical value [Km/h].

VEH SPEED 2

Display the vehicle speed signal received from ABS or VDC or CVT by numerical value [Km/h].

DOOR STAT-DR

Indicates [LOCK/READY/UNLOCK] condition of driver side door status.

DOOR STAT-AS

Indicates [LOCK/READY/UNLOCK] condition of passenger side door status.

ID OK FLAG

Indicates [SET/RESET] condition of key ID.

PRMT ENG STRT

Indicates [SET/RESET] condition of engine start possibility.

PRMT RKE STRT

NOTE:
This item is displayed, but cannot be monitored. 

KEY SW -SLOT

Indicates [ON/OFF] condition of key slot.

TRNK/HAT MNTR

NOTE:
This item is displayed, but cannot be monitored. 

RKE-LOCK

Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.

RKE-UNLOCK

Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.

RKE-TR/BD

NOTE:
This item is displayed, but cannot be monitored. 

RKE-PANIC

Indicates [ON/OFF] condition of PANIC button of Intelligent Key.

RKE-P/W OPEN

Indicates [ON/OFF] condition of P/W DOWN signal from Intelligent Key.

Monitor Item

Condition

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-29

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

*: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.

ACTIVE TEST

RKE-MODE CHG

Indicates [ON/OFF] condition of MODE CHANGE signal from Intelligent Key.

RKE OPE COUN1

When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the 
numerical value start changing.

RKE OPE COUN2

NOTE:
This item is displayed, but cannot be monitored. 

Monitor Item

Condition

Test item

Description

BATTERY SAVER

This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT-III screen is touched.

PW REMOTO DOWN SET

This test is able to check power window down operation.
The power window down will be activated after “ON” on CONSULT-III screen is touched.

INSIDE BUZZER

This test is able to check warning chime in combination meter operation.
• Take away warning chime sounds when “TAKE OUT” on CONSULT-III screen is touched.
• Key warning chime sounds when “KEY WARN” on CONSULT-III screen is touched.
• P position warning chime sounds when “P RNG WARN” on CONSULT-III screen is touched.
• ACC warning chime sounds when “ACC WARN” on CONSULT-III screen is touched.

OUTSIDE BUZZER

This test is able to check Intelligent Key warning buzzer operation.
The Intelligent Key warning buzzer will be activated after “ON” on CONSULT-III screen is touched.

INDICATOR

This test is able to check warning lamp operation.
• “KEY” Warning lamp illuminates when “KEY ON” on CONSULT-III screen is touched.
• “KEY” Warning lamp flashes when “KEY IND” on CONSULT-III screen is touched.

INT LAMP

This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT-III screen is touched.

LCD

This test is able to check meter display information
• Engine start information displays when “BP N” on CONSULT-III screen is touched.
• Engine start information displays when “BP I” on CONSULT-III screen is touched.
• Key ID warning displays when “ID NG” on CONSULT-III screen is touched.
• Steering lock information displays when “ROTAT” on CONSULT-III screen is touched.

NOTE:
For models without steering lock unit, “ROTAT” is displayed, but cannot be tested.

• P position warning displays when “SFT P” on CONSULT-III screen is touched.
• Intelligent Key insert information displays when “INSRT” on CONSULT-III screen is touched.
• Intelligent Key low battery warning displays when “BATT” on CONSULT-III screen is touched.
• Take away through window warning displays when “NO KY” on CONSULT-III screen is touched.
• Take away warning display when “OUTKEY” on CONSULT-III screen is touched.
• OFF position warning display when “LK WN” on CONSULT-III screen is touched.

TRUNK/GLASS HATCH

This test is able to check back door opener actuator open operation.
This actuator opens when “ON” on CONSULT-III screen is touched.

FLASHER

This test is able to check hazard warning lamp operation.
The hazard warning lamps will be activated after “ON” on CONSULT-III screen is touched.

HORN

This test is able to check horn operation.
The horn will be activated after “ON” on CONSULT-III screen is touched.

IGN CONT2

This test is able to check ignition relay operation.
The ignition relay will be activated after “ON” on CONSULT-III screen is touched.

P RANGE

This test is able to check CVT shift selector power supply
CVT shift selector power is supplied when “ON” on CONSULT-III screen is touched.

ENGINE SW ILLUMI

This test is able to check push-ignition switch illumination operation.
Push-ignition switch illumination illuminates when “ON” on CONSULT-III screen is touched.

LOCK INDICATOR

NOTE:
This item is displayed, but cannot be tested.

ACC INDICATOR

This test is able to check indicator in push-ignition switch operation.
Indicator in push-button ignition switch illuminates when “ON” on CONSULT-III screen is touched.

BCS-30

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM)

COMB SW

COMB SW : CONSULT-III Function (BCM - COMB SW)

INFOID:0000000005518285

DATA MONITOR

IGNITION ON IND

This test is able to check indicator in push-ignition switch operation.
Indicator in push-button ignition switch illuminates when “ON” on CONSULT-III screen is touched.

KEY SLOT ILLUMI

This test is able to check key slot illumination operation.
Key slot illumination flash when “ON” on CONSULT-III screen is touched.

AUTOMATIC BACK DOOR

NOTE:
This item is displayed, but cannot be tested.

AUTOMATIC SLIDING DOOR

NOTE:
This item is displayed, but cannot be tested.

Test item

Description

Monitor item [UNIT]

Description

FR WIPER HI
[Off/On]

Displays the status of the FR WIPER HI switch in combination switch judged by BCM with the combination 
switch reading function.

FR WIPER LOW
[Off/On]

Displays the status of the FR WIPER LOW switch in combination switch judged by BCM with the combination 
switch reading function.

FR WASHER SW
[Off/On]

Displays the status of the FR WASHER switch in combination switch judged by BCM with the combination 
switch reading function.

FR WIPER INT
[Off/On]

Displays the status of the FR WIPER INT switch in combination switch judged by BCM with the combination 
switch reading function.

FR WIPER STOP
[Off/On]

Displays the status of the front wiper stop position signal received from IPDM E/R via CAN communication.

INT VOLUME
[1 - 7]

Displays the status of wiper intermittent dial position judged by BCM with the combination switch reading 
function.

RR WIPER ON
[Off/On]

Displays the status of the RR WIPER ON switch in combination switch judged by BCM with the combination 
switch reading function.

RR WIPER INT
[Off/On]

Displays the status of the RR WIPER INT switch in combination switch judged by BCM with the combination 
switch reading function.

RR WASHER SW
[Off/On]

Displays the status of the RR WASHER switch in combination switch judged by BCM with the combination 
switch reading function.

RR WIPER STOP
[Off/On]

Displays the status of the rear wiper stop position signal received from rear wiper motor.

TURN SIGNAL R
[Off/On]

Displays the status of the TURN RH switch in combination switch judged by BCM with the combination switch 
reading function.

TURN SIGNAL L
[Off/On]

Displays the status of the TURN LH switch in combination switch judged by BCM with the combination switch 
reading function.

TAIL LAMP SW
[Off/On]

Displays the status of the TAIL LAMP switch in combination switch judged by BCM with the combination 
switch reading function.

HI BEAM SW
[Off/On]

Displays the status of the HI BEAM switch in combination switch judged by BCM with the combination switch 
reading function.

HEAD LAMP SW 1
[Off/On]

Displays the status of the HEADLAMP 1 switch in combination switch judged by BCM with the combination 
switch reading function.

HEAD LAMP SW 2
[Off/On]

Displays the status of the HEADLAMP 2 switch in combination switch judged by BCM with the combination 
switch reading function.

PASSING SW
[Off/On]

Displays the status of the PASSING switch in combination switch judged by BCM with the combination switch 
reading function.

AUTO LIGHT SW
[Off/On]

Displays the status of the AUTO LIGHT switch in combination switch judged by BCM with the combination 
switch reading function.