Nissan Murano Z51. Manual - part 205

AV

DIAGNOSIS SYSTEM (AV CONTROL UNIT)

AV-599

< SYSTEM DESCRIPTION >

[BOSE AUDIO WITH NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

• “Audio” and “Amp” indicate the same status because “Amp” indicates the status of the amplifier integrated in the AV control unit.

• “STRG SW”, “Amp”“XM” indicate the same status as “Audio”.

Hands-Free Phone

The hands-free phone reception volume adjustment, microphone
and speaker test, and memory erase functions are also available.

Camera Cont.

The two functions of “Connection Confirmation” and “Adjust Offset of Rear View Camera” are available.
CONNECTION CONFIRMATION
The steering angle sensor, reverse signal and vehicle speed sensor
can be inspected.

ADJUST OFFSET OF REAR VIEW CAMERA

JSNIA0083GB

JSNIA0084GB

Diagnosis item

Display

Vehicle status

Steer. Angle Sensor

ON

When steering the vehicle with ignition switch ON (remains ON until connection 
mode is stopped when it is turned ON)

OFF

• Ignition switch at ACC
• No steering with ignition switch ON

—

Malfunction detected in camera connection recognition signal

Reverse Sensor

ON

Selector lever is in “R” with ignition switch ON.

OFF

• Ignition switch at ACC
• Selector lever is in position other than “R” with ignition switch ON.

—

Malfunction detected in camera-connection recognition signal

Vehicle Speed Sensor

ON

Vehicle speed is more than 0 km/h (0 MPH) with ignition switch ON

OFF

• Ignition switch at ACC
• Vehicle speed is 0 km/h (0 MPH) with ignition switch ON

—

Malfunction detected in camera connection recognition signal

Side view Switch

—

Not used

AV-600

< SYSTEM DESCRIPTION >

[BOSE AUDIO WITH NAVIGATION]

DIAGNOSIS SYSTEM (AV CONTROL UNIT)

Use this mode to adjust the guide line display position of the rear-
view monitor if necessary after removing the rear view monitor cam-
era.

Bluetooth

Confirm / Change Passkey 
• The Bluetooth passkey can be confirmed and changed.
• The passkey can be changed by four digits within 0 to 9.

Confirm / Change Device Name
• The Bluetooth device name be confirmed and changed.
• The device name can be changed by sixteen digits from A to Z

(small characters can be used) and “-” (hyphens).

SAT 

• Change Channel
- Any necessary channels required to receive traffic information from

the satellite radio system can be set.

JSNIA0085GB

JSNIA0086GB

JSNIA0087GB

JSNIA0092GB

AV

DIAGNOSIS SYSTEM (AV CONTROL UNIT)

AV-601

< SYSTEM DESCRIPTION >

[BOSE AUDIO WITH NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

• Change Application ID
- Any application ID'-s required to receive traffic information from the

satellite radio system can be set.

Delete Unit Connection Log

Deletes any unit connection records and error records from the AV
control unit memory. (Clear the records of the unit that has been
removed.)

Initialize Settings

Deletes data stored in HDD.

CONSULT-III Function (MULTI AV)

INFOID:0000000005528696

CONSULT-III FUNCTIONS

CONSULT-III performs the following functions via the communication with the AV control unit.

AV COMMUNICATION

When “AV communication” of “CAN Diag Support Monitor” is selected, the following function will be performed.

ECU IDENTIFICATION

The part number of AV control unit is displayed.

JSNIA0093GB

JSNIA0088GB

JSNIA0095GB

Diagnosis mode

Description

Ecu Identification

The part number of AV control unit can be checked.

Self Diagnostic Result

Performs a diagnosis on the AV control unit and a connection diagnosis for the communication 
circuit of the MULTI AV system, and displays the current and past malfunctions collectively.

Data Monitor

The diagnosis of vehicle signal that is input to the AV control unit can be performed.

AV communication

AV&NAVI C/U

Displays the communication status from AV control unit to each unit as well as the error 
counter.

AUDIO

Displays the AV control unit communication status and the error counter.

AV-602

< SYSTEM DESCRIPTION >

[BOSE AUDIO WITH NAVIGATION]

DIAGNOSIS SYSTEM (AV CONTROL UNIT)

SELF DIAGNOSIS RESULT

• In CONSULT-III self-diagnosis, self-diagnosis results and error history are displayed collectively.
• A current malfunction indicates “crnt”. a past malfunction indicates “past”.
• The timing is displayed as “0” if any of the error codes [U1000], [U1010], [U1300] and [U1310] is detected.

the counter increases by 1 if the status is normal at the next ignition switch on cycle.

Self-diagnosis Results Display Item

Error item

Description

Possible malfunction factor/Action to take

CAN COMM CIRCUIT [U1000]

CAN communication malfunction is detect-
ed.

Refer to 

AV-605, "Diagnosis Procedure"

.

CONTROL UNIT (CAN) [U1010]

CAN initial diagnosis malfunction is detect-
ed.

Replace the AV control unit.

CONTROL UNIT (AV) [U1310]

AV communication circuit initial diagnosis 
malfunction is detected.

Control Unit FLASH-ROM [U1200]

AV control unit malfunction is detected.

Gyro NO CONN [U1201]

CAN CONT [U1216]

BLUETOOTH CONN [U1217]

HDD CONN [U1218]

HDD READ [U1219]

XM SERIAL COMM [U1220]

HDD WRITE [U121A]

HDD COMM [U121B]

HDD ACCESS [U121C]

DSP CONN [U121D]

DSP COMM [U121E]

INTERNAL COMM [U121F]

Malfunction is detected in AV control unit 
power supply and ground circuits.

Check AV control unit power supply and 
ground circuits. When detecting no mal-
function in those components, replace AV 
control unit.

GPS COMM [U1204]

GPS malfunction is detected.

An intermittent error caused by strong radio 
interference may be detected unless a 
symptom (GPS reception error, etc.) oc-
curs.
Replace the AV control unit if the malfunc-
tion occurs constantly.

GPS ROM [U1205]

GPS RAM [U1206]

GPS RTC [U1207]

FRONT DISP CONN [U1243]

When either one of the following items are 
detected:
• front display unit power supply and 

ground circuits are malfunctioning.

• serial communication circuits between 

AV control unit and front display unit are 
malfunctioning.

• serial communication signal between AV 

control unit and front display unit is mal-
functioning.

• Front display unit power supply and 

ground circuits.

• Serial communication circuits between 

AV control unit and display unit.

GPS ANTENNA CONN [U1244]

GPS antenna connection malfunction is de-
tected.

GPS antenna.

CAMERA CONT CONN [U1250]

Malfunction is detected in camera connec-
tion recognition circuit between AV control 
unit and camera control unit.

Camera-connection recognition circuit be-
tween AV control unit and camera control 
unit.

XM ANTENNA CONN [U1258]

Satellite radio antenna connection malfunc-
tion is detected.

• Satellite radio antenna feeder.
• Antenna base.