Nissan Murano Z51. Manual - part 1522

WT-26

< DTC/CIRCUIT DIAGNOSIS >

C1704, C1705, C1706, C1707 LOW TIRE PRESSURE

CAUTION:

Stop the vehicle and within 5 minutes, use “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”
to display the tire pressure for all wheels.

Is the inspection result normal?

YES

>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.

NO

>> GO TO 1.

Special Repair Requirement

INFOID:0000000005575986

1.

CHECK TIRE PRESSURE

Check all tires for tire pressures. Refer to 

WT-60, "Tire Air Pressure"

.

Does all tire pressure data meet the specification?

YES

>> GO TO 2.

NO

>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.

2.

PERFORM ID REGISTRATION

Perform ID registration. Refer to 

WT-22, "ID REGISTRATION PROCEDURE : Special Repair Requirement"

.

>> END

C1708, C1709, C1710, C1711 TRANSMITTER

WT-27

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

C1708, C1709, C1710, C1711 TRANSMITTER

DTC Logic

INFOID:0000000005575987

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

DTC REPRODUCTION PROCEDURE

With CONSULT-III

1.

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.

2.

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.

Is DTC “C1708”, “C1709”, “C1710”, “C1711” detected?

YES

>> Perform trouble diagnosis. Refer to 

WT-27, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000005575988

1.

CHECK TIRE PRESSURE SIGNAL

With CONSULT-III

1.

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.

2.

Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

3.

Select “BCM” in “DATA MONITOR”, and check that the tire pressures match the standard value.

CAUTION:

Stop the vehicle and within 5 minutes, use “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”
to display the tire pressure for all wheels.

Is a tire pressure of 0 kPa (0 Psi) displayed for all wheels?

YES

>> GO TO 2.

NO

>> GO TO 5.

2.

CHECK HARNESS BETWEEN BCM AND TIRE PRESSURE RECEIVER

1.

Turn the ignition switch OFF.

2.

Disconnect BCM harness connector and tire pressure receiver harness connector.

3.

Check the continuity between BCM harness connector and tire pressure receiver harness connector.

DTC

Display item

Malfunction detected condition

Possible cause

C1708

[NO DATA] FL

Tire pressure data signal from the front left wheel 
transmitter cannot be detected.

• Harness or connector

(Tire pressure receiver, BCM)

• ID registration is not finished
• Transmitter malfunction
• BCM malfunction

C1709

[NO DATA] FR

Tire pressure data signal from the front right wheel 
transmitter cannot be detected.

C1710

[NO DATA] RR

Tire pressure data signal from the rear right wheel 
transmitter cannot be detected.

C1711

[NO DATA] RL

Tire pressure data signal from the rear left wheel 
transmitter cannot be detected.

Monitor item

Condition

Displayed value

AIR PRESS FL

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or 
more, then drive normally for 10 minutes.

Internal pressure of tires

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

WT-28

< DTC/CIRCUIT DIAGNOSIS >

C1708, C1709, C1710, C1711 TRANSMITTER

4.

Check the continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace damaged parts.

3.

CHECK TIRE PRESSURE RECEIVER POWER SUPPLY CIRCUIT 

1.

Connect the BCM harness connector.

2.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

3.

Check the voltage between the BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace damaged parts.

4.

CHECK TIRE PRESSURE RECEIVER

Check tire pressure receiver. Refer to 

WT-36, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace tire pressure receiver. Refer to 

WT-59, "Removal and Installation"

.

5.

CHECK ID REGISTRATION

Perform ID registration of all transmitters. Refer to 

WT-22, "ID REGISTRATION PROCEDURE : Special

Repair Requirement"

.

Can ID registration of all transmitters be completed?

YES

>> GO TO 6.

NO

>> Replace transmitter. Refer to 

WT-57, "Exploded View"

.

6.

CHECK TIRE PRESSURE MONITORING SYSTEM

With CONSULT-III

1.

Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.

2.

Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

3.

Select “BCM” in “DATA MONITOR”, and check that the tire pressures match the standard value.

BCM

Tire pressure receiver

Continuity

Connector

Terminal

Connector

Terminal

M123

137

M21

1

Existed

138

4

139

2

BCM

—

Continuity

Connector

Terminal

M123

137

Ground

Not existed

138

139

BCM

—

Voltage

Connector

Terminal

M123

138

Ground

5 V

C1708, C1709, C1710, C1711 TRANSMITTER

WT-29

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

CAUTION:

Stop the vehicle and within 15 minutes, use “DATA MONITOR” in “AIR PRESSURE MONITOR” of
“BCM”   to read the tire pressure for all wheels.
Is the inspection result normal?

YES

>> Replace the DTC-detected malfunctioning transmitter. Refer to 

WT-57, "Exploded View"

.

NO

>> Replace BCM. Refer to 

BCS-95, "Exploded View"

.

Special Repair Requirement

INFOID:0000000005575989

1.

CHECK TIRE PRESSURE

Check all tires for tire pressures. Refer to 

WT-60, "Tire Air Pressure"

.

Does all tire pressure data meet the specification?

YES

>> GO TO 2.

NO

>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.

2.

PERFORM ID REGISTRATION

Perform ID registration. Refer to 

WT-22, "ID REGISTRATION PROCEDURE : Special Repair Requirement"

.

>> END

Monitor item

Condition

Displayed value

AIR PRESS FL

Drive at a speed of 40 km/h (25 MPH) or more, for several 
minutes without stopping.

Internal pressure of tires

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL