Nissan Murano Z51. Manual - part 1261

B2612 STEERING STATUS

SEC-91

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

Is the inspection result normal?

YES

>> GO TO 10.

NO

>> Repair or replace harness or connector.

10.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-39, "Intermittent Incident"

.

>> INSPECTION END

Steering lock unit

Ground

Continuity

Connector

Terminal

M12

3

Not existed

SEC-92

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2617 STARTER RELAY CIRCUIT

B2617 STARTER RELAY CIRCUIT

Description

INFOID:0000000005515579

Located in IPDM E/R, it runs the starter motor. The starter relay is turned ON by the BCM when the ignition
switch is in START position. IPDM E/R transmits the starter relay ON signal to BCM via CAN communication.

DTC Logic

INFOID:0000000005515580

DTC DETECTION LOGIC

NOTE:
• If DTC B2617 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

SEC-32, "BCM : DTC Logic"

.

• If DTC B2617 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

SEC-34, "BCM : DTC Logic"

.

• If DTC B2617 is displayed with DTC B210E for IPDM E/R, first perform the trouble diagnosis for DTC

B210E. Refer to 

SEC-108, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON under the following conditions and wait for at least 1 second.

-

Selector lever is in the P or N position.

-

Do not depress brake pedal.

2.

Check “Self diagnostic result” with CONSULT-III.

Is DTC detected?

YES

>> Go to 

SEC-92, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000005515581

1.

CHECK STARTER RELAY

1.

Turn ignition switch ON.

2.

Check voltage between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK STARTER RELAY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect BCM connector and IPDM E/R connector.

3.

Check continuity between IPDM E/R harness connector and BCM harness connector.

DTC No.

Trouble diagnosis 

name

DTC detecting condition

Possible cause

B2617

BCM

An immediate operation of starter relay is request-
ed by BCM, but there is no response for more than 
1 second

• Harness or connectors

(Starter relay circuit is open or short-
ed.)

• IPDM E/R

(+)

(–)

Condition

Voltage (V)

(Approx.)

BCM

Connector

Terminal

M121

52

Ground

Selector lever

N or P position

Battery voltage

Other than above

0

B2617 STARTER RELAY CIRCUIT

SEC-93

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

4.

Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-35, "Removal and Installation"

.

NO

>> Repair or replace harness or connector.

3.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-39, "Intermittent Incident"

.

>> INSPECTION END

IPDM E/R

BCM

Continuity

Connector

Terminal

Connector

Terminal

E11

46

M121

52

Existed

IPDM E/R

Ground

Continuity

Connector

Terminal

E11

46

Not existed

SEC-94

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2619 BCM

B2619 BCM

Description

INFOID:0000000005515582

BCM requests IPDM E/R to supply power to steering lock unit. After receiving the power, the steering lock unit
transmits an ON signal to BCM.

DTC Logic

INFOID:0000000005515583

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Press the push-button ignition switch under the following conditions and wait for at least 1 second.

-

Selector lever is in the P or N position.

-

Do not depress brake pedal.

2.

Check “Self diagnostic result” with CONSULT-III.

Is DTC detected?

YES

>> Go to 

SEC-94, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000005515584

1.

INSPECTION START

1.

Turn ignition switch ON.

2.

Check “Self diagnostic result” with CONSULT-III.

3.

Touch “ERASE”.

4.

Perform DTC Confirmation Procedure.
See 

SEC-94, "DTC Logic"

.

Is the DTC B2619 displayed again?

YES

>> Replace BCM. Refer to 

BCS-95, "Removal and Installation"

.

NO

>> INSPECTION END

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B2619

BCM

BCM detects a mismatch between the power supplied to the 
steering lock unit and the feedback for one second or more.

BCM