Nissan Murano Z51. Manual - part 1075

 

  Главная      Nissan     Nissan Murano Z51 (2010 year) - Service Manual

 

поиск по сайту            

 

 

 

 

 

 

 

 

 

содержание   ..  1073  1074  1075  1076   ..

 

 

Nissan Murano Z51. Manual - part 1075

 

 

PCS-42

< SYSTEM DESCRIPTION >

[POWER DISTRIBUTION SYSTEM]

DIAGNOSIS SYSTEM (BCM)

DIAGNOSIS SYSTEM (BCM)

COMMON ITEM

COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)

INFOID:0000000005683267

APPLICATION ITEM

CONSULT-III performs the following functions via CAN communication with BCM.

SYSTEM APPLICATION

BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.

×

: Applicable item

NOTE:

• *1: For models with rain sensor this mode is displayed, but is not used.

• *2: This item is displayed, but is not used. 

FREEZE FRAME DATA (FFD)

Diagnosis mode

Function Description

Work Support

Changes the setting for each system function.

Self Diagnostic Result

Displays the diagnosis results judged by BCM.

CAN Diag Support Monitor

Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
tion manual.

Data Monitor

The BCM input/output signals are displayed.

Active Test

The signals used to activate each device are forcibly supplied from BCM.

Ecu Identification

The BCM part number is displayed.

Configuration

• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.

System

Sub system selection item

Diagnosis mode

Work Support

Data Monitor

Active Test

Door lock

DOOR LOCK

×

×

×

Rear window defogger

REAR DEFOGGER

×

×

Warning chime

BUZZER

×

×

Interior room lamp timer

INT LAMP

×

×

×

Exterior lamp

HEAD LAMP

×

×

×

Wiper and washer

WIPER

×

*

1

×

×

Turn signal and hazard warning lamps

FLASHER

×

×

×

AIR CONDITONER*

2

• Intelligent Key system
• Engine start system

INTELLIGENT KEY

×

×

×

Combination switch

COMB SW

×

Body control system

BCM

×

NVIS - NATS

IMMU

×

×

Interior room lamp battery saver

BATTERY SAVER

×

×

×

Back door opener system

TRUNK

×

×

Vehicle security system

THEFT ALM

×

×

×

RAP system

RETAINED PWR

×

Signal buffer system

SIGNAL BUFFER

×

×

TPMS

TPMS (AIR PRESSURE MONITOR)

×

×

×

PCS

DIAGNOSIS SYSTEM (BCM)

PCS-43

< SYSTEM DESCRIPTION >

[POWER DISTRIBUTION SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT-III.

INTELLIGENT KEY

INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)

INFOID:0000000005683268

BCM CONSULT-III FUNCTION

CONSULT-III performs the following functions via CAN communication with BCM.

CONSULT screen item

Indication/Unit

Description

Vehicle Speed

km/h

Vehicle speed of the moment a particular DTC is detected

Odo/Trip Meter

km

Total mileage (Odometer value) of the moment a particular DTC is detected

Vehicle Condition

SLEEP>LOCK

Power position status of 
the moment a particular 
DTC is detected

While turning BCM status from low power consumption mode to 
normal mode (Power supply position is “LOCK”)

SLEEP>OFF

While turning BCM status from low power consumption mode to 
normal mode (Power supply position is “OFF”.)

LOCK>ACC

While turning power supply position from “LOCK” to “ACC”

ACC>ON

While turning power supply position from “ACC” to “IGN”

RUN>ACC

While turning power supply position from “RUN” to “ACC” (Vehicle 
is stopping and selector lever is except P position.)

CRANK>RUN

While turning power supply position from “CRANKING” to “RUN” 
(From cranking up the engine to run it)

RUN>URGENT

While turning power supply position from “RUN“ to “ACC” (Emer-
gency stop operation)

ACC>OFF

While turning power supply position from “ACC” to “OFF”

OFF>LOCK

While turning power supply position from “OFF” to “LOCK”

OFF>ACC

While turning power supply position from “OFF” to “ACC”

ON>CRANK

While turning power supply position from “IGN” to “CRANKING”

OFF>SLEEP

While turning BCM status from normal mode (Power supply posi-
tion is “OFF”.) to low power consumption mode

LOCK>SLEEP

While turning BCM status from normal mode (Power supply posi-
tion is “LOCK”.) to low power consumption mode

LOCK

Power supply position is “LOCK” (Ignition switch OFF with steer-
ing is locked.)

OFF

Power supply position is “OFF” (Ignition switch OFF with steering 
is unlocked.)

ACC

Power supply position is “ACC” (Ignition switch ACC)

ON

Power supply position is “IGN” (Ignition switch ON with engine 
stopped)

ENGINE RUN

Power supply position is “RUN” (Ignition switch ON with engine 
running)

CRANKING

Power supply position is “CRANKING” (At engine cranking)

IGN Counter

0 - 39

The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1 

 2 

 3...38 

 39 after returning to the normal condition 

whenever ignition switch OFF 

 ON.

• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.

Diagnosis mode

Function Description

WORK SUPPORT

Changes the setting for each system function.

SELF-DIAG RESULTS

Displays the diagnosis results judged by BCM.

PCS-44

< SYSTEM DESCRIPTION >

[POWER DISTRIBUTION SYSTEM]

DIAGNOSIS SYSTEM (BCM)

WORK SUPPORT

SELF-DIAG RESULT

Refer to 

BCS-90, "DTC Index"

.

DATA MONITOR

DATA MONITOR

The BCM input/output signals are displayed.

ACTIVE TEST

The signals used to activate each device are forcibly supplied from BCM.

Diagnosis mode

Function Description

Monitor item

Description

REMO CONT ID CONFIR

It can be checked whether Intelligent Key ID code is registered or not in this mode.

AUTO LOCK SET

Auto door lock time can be changed in this mode.
• MODE 1: 1 minute
• MODE 2: 5 minutes
• MODE 3: 30 seconds
• MODE 4: 2 minutes

LOCK/UNLOCK BY I-KEY

Door lock/unlock function by door request switch (driver side, passenger side and back door) mode 
can be changed to operate (ON) or not operate (OFF) in this mode.

ENGINE START BY I-KEY

Engine start function mode can be changed to operate (ON) or not operate (OFF) with this mode. 

TRUNK/GLASS HATCH OPEN

Buzzer reminder function mode by back door request switch can be changed to operate (ON) or 
not operate (OFF) with this mode.

PANIC ALARM SET

Panic alarm button pressing time on Intelligent Key remote control button can be selected from the 
following with this mode. 
• MODE 1: 0.5 sec.
• MODE 2: Non-operation
• MODE 3: 1.5 sec.

PW DOWN SET

Unlock button pressing time on Intelligent Key button can be selected from the following with this 
mode. 
• MODE 1: 3 sec.
• MODE 2: Non-operation
• MODE 3: 5 sec.

TRUNK OPEN DELAY

NOTE:
This item is displayed, but cannot be supported. 

LO- BATT OF KEY FOB WARN

Intelligent Key low battery warning mode can be changed to operate (ON) or not operate (OFF) 
with this mode. 

ANTI KEY LOCK IN FUNCTI

Key reminder function mode can be changed to operate (ON) or not operate (OFF) with this mode.

HAZARD ANSWER BACK

Hazard reminder function mode can be selected from the following with this mode.
• LOCK ONLY: Door lock operation only
• UNLOCK ONLY: Door unlock operation only
• LOCK/UNLOCK: Lock/unlock operation
• OFF: Non-operation

ANS BACK I-KEY LOCK

Buzzer reminder function (lock operation) mode by door request switch (driver side and passenger 
side) can be selected from the following with this mode. 
• Horn chirp: Sound horn
• Buzzer: Sound Intelligent Key warning buzzer
• OFF: Non-operation

ANS BACK I-KEY UNLOCK

Buzzer reminder function (unlock operation) mode by door request switch can be changed to op-
erate (ON) or not operate (OFF) with this mode.

SHORT CRANKING OUTPUT

Starter motor can operate during the times below.
• 70 msec
• 100  msec
• 200  msec

INSIDE ANT DIAGNOSIS

This function allows inside key antenna self-diagnosis.

HORN WITH KEYLESS LOCK

Horn reminder function mode by Intelligent Key button can be changed to operate (ON) or not op-
erate (OFF) with this mode.

PCS

DIAGNOSIS SYSTEM (BCM)

PCS-45

< SYSTEM DESCRIPTION >

[POWER DISTRIBUTION SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

Monitor Item

Condition

REQ SW -DR

Indicates [ON/OFF] condition of door request switch (driver side).

REQ SW -AS

Indicates [ON/OFF] condition of door request switch (passenger side).

REQ SW -RR

NOTE:
This item is displayed, but cannot be monitored. 

REQ SW -RL

NOTE:
This item is displayed, but cannot be monitored. 

REQ SW -BD/TR

Indicates [ON/OFF] condition of back door request switch.

PUSH SW

Indicates [ON/OFF] condition of push-button ignition switch.

IGN RLY2 -F/B

Indicates [ON/OFF] condition of ignition relay 2.

ACC RLY-FB

NOTE:
This item is displayed, but cannot be monitored. 

CLUCH SW

NOTE:
This item is displayed, but cannot be monitored. 

BRAKE SW 1

Indicates [ON/OFF]* condition of brake switch power supply.

BRAKE SW 2

Indicates [ON/OFF] condition of brake switch.

DETE/CANCL SW

Indicates [ON/OFF] condition of P position.

SFT PN/N SW

Indicates [ON/OFF] condition of P or N position.

S/L -LOCK

Indicates [ON/OFF] condition of steering lock unit (LOCK).
NOTE:
For models without steering lock unit this item is not displayed.

S/L -UNLOCK

Indicates [ON/OFF] condition of steering lock unit (UNLOCK).
NOTE:
For models without steering lock unit this item is not displayed.

S/L RELAY -F/B

Indicates [ON/OFF] condition of ignition switch.
NOTE:
For models without steering lock unit this item is not displayed.

UNLK SEN -DR

Indicates [ON/OFF] condition of driver door UNLOCK status.

PUSH SW -IPDM

Indicates [ON/OFF] condition of push-button ignition switch.

IGN RLY1 -F/B

Indicates [ON/OFF] condition of ignition relay 1.

DETE SW -IPDM

Indicates [ON/OFF] condition of P position.

SFT PN -IPDM

Indicates [ON/OFF] condition of P or N position.

SFT P -MET

Indicates [ON/OFF] condition of P position.

SFT N -MET

Indicates [ON/OFF] condition of N position.

ENGINE STATE

Indicates [STOP/START/CRANK/RUN] condition of engine states.

S/L LOCK-IPDM

Indicates [ON/OFF] condition of steering lock unit (LOCK).
NOTE:
For models without steering lock unit this item is not displayed.

S/L UNLK-IPDM

Indicates [ON/OFF] condition of steering lock unit (UNLOCK).
NOTE:
For models without steering lock unit this item is not displayed.

S/L RELAY-REQ

Indicates [ON/OFF] condition of steering lock relay.
NOTE:
For models without steering lock unit this item is not displayed.

VEH SPEED 1

Display the vehicle speed signal received from combination meter by numerical value [Km/h].

VEH SPEED 2

Display the vehicle speed signal received from ABS or VDC or CVT by numerical value [Km/h].

DOOR STAT-DR

Indicates [LOCK/READY/UNLOCK] condition of driver side door status.

DOOR STAT-AS

Indicates [LOCK/READY/UNLOCK] condition of passenger side door status.

ID OK FLAG

Indicates [SET/RESET] condition of key ID.

PRMT ENG STRT

Indicates [SET/RESET] condition of engine start possibility.

 

 

 

 

 

 

 

содержание   ..  1073  1074  1075  1076   ..