Murano Cross Cabriolet Z51 (2013 year). Manual - part 94

B1338, B1340, B1341, B1342 SATELLITE SENSOR RH

SRC-169

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

YES

>> GO TO 1. 

NO

>> INSPECTION END

Revision: 2012 October

2013 Murano CrossCabriolet

SRC-170

< DTC/CIRCUIT DIAGNOSIS >

B1339 SATELLITE SENSOR RH

B1339 SATELLITE SENSOR RH

DTC Logic

INFOID:0000000008461962

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-13, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-170, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000008461963

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

1.

REPLACE FRONT DOOR SATELLITE SENSOR

1.

Replace front door satellite sensor RH. Refer to 

SR-28, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-170, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 2. 

NO

>> INSPECTION END

2.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-170, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1. 

NO

>> INSPECTION END

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1339

FR-RH DOOR SATEL 
SENS 
[MIS-INSTALLATION]

Front door satellite sensor RH is out of the 
specified specification

Diagnosis sensor unit or front door satellite sen-
sor RH is different from the part specified

Revision: 2012 October

2013 Murano CrossCabriolet

B1343, B1344 SATELLITE SENSOR LH

SRC-171

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1343, B1344 SATELLITE SENSOR LH

DTC Logic

INFOID:0000000008461964

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-13, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-171, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000008461965

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3. 

NO

>> Replace wiring harness.

3.

REPLACE FRONT DOOR SATELLITE SENSOR

1.

Replace front door satellite sensor LH. Refer to 

SR-28, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-171, "DTC Logic"

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-171, "DTC Logic"

.

Is DTC detected?

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1343
B1344

FR-LH DOOR SATEL 
SENS
[SENSOR MALFUNC-
TION]

Front door satellite sensor LH is malfunc-
tioning

• Harness or connectors
• Malfunction in front door satellite sensor LH
• Malfunction in air bag diagnosis sensor unit

Revision: 2012 October

2013 Murano CrossCabriolet

SRC-172

< DTC/CIRCUIT DIAGNOSIS >

B1343, B1344 SATELLITE SENSOR LH

YES

>> GO TO 1. 

NO

>> INSPECTION END

Revision: 2012 October

2013 Murano CrossCabriolet

B1345, B1347, B1348, B1349 SATELLITE SENSOR LH

SRC-173

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1345, B1347, B1348, B1349 SATELLITE SENSOR LH

DTC Logic

INFOID:0000000008461966

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-13, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to 

SRC-176, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000008461967

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3. 

NO

>> Replace wiring harness.

3.

REPLACE SATELLITE SENSOR

1.

Replace front door satellite sensor LH. Refer to 

SR-28, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-176, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-176, "DTC Logic"

.

Is DTC detected?

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1345
B1347
B1348
B1349

FR-LH DOOR SATEL 
SENS
[COMM MALFUNC-
TION]

Front door satellite sensor LH is malfunc-
tioning

• Harness or connectors
• Malfunction in front door satellite sensor LH
• Malfunction in air bag diagnosis sensor unit

Revision: 2012 October

2013 Murano CrossCabriolet

SRC-174

< DTC/CIRCUIT DIAGNOSIS >

B1345, B1347, B1348, B1349 SATELLITE SENSOR LH

YES

>> GO TO 1. 

NO

>> INSPECTION END

Revision: 2012 October

2013 Murano CrossCabriolet

B1346 SATELLITE SENSOR LH

SRC-175

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1346 SATELLITE SENSOR LH

DTC Logic

INFOID:0000000008461968

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-13, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-175, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000008461969

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

REPLACE FRONT DOOR SATELLITE SENSOR

1.

Replace front door satellite sensor LH. Refer to 

SR-28, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-175, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 2. 

NO

>> INSPECTION END

2.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-175, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1. 

NO

>> INSPECTION END

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1346

FR-LH DOOR SATEL 
SENS
[MIS-INSTALLATION]

Front door satellite sensor LH is out of the 
specified specification

Diagnosis sensor unit or front door satellite sen-
sor LH is different from the part specified

Revision: 2012 October

2013 Murano CrossCabriolet

SRC-176

< DTC/CIRCUIT DIAGNOSIS >

B1350, B1351 SATELLITE SENSOR

B1350, B1351 SATELLITE SENSOR

DTC Logic

INFOID:0000000008461970

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-13, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-176, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000008461971

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

REPLACE BOTH OF FRONT DOOR SATELLITE SENSOR

1.

Replace both of front door satellite sensor. Refer to 

SR-28, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-176, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 2. 

NO

>> INSPECTION END

2.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-176, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1. 

NO

>> INSPECTION END

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1350
B1351

FR DOOR SATEL SENS

Front door satellite sensor is malfunction-
ing or out of the specified specification

• Malfunction in front door satellite sensor LH/RH
• Malfunction in air bag diagnosis sensor unit

Revision: 2012 October

2013 Murano CrossCabriolet

SRS AIR BAG WARNING LAMP DOES NOT TURN OFF

SRC-177

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

SYMPTOM DIAGNOSIS

SRS AIR BAG WARNING LAMP DOES NOT TURN OFF

Diagnosis Procedure

INFOID:0000000008461972

1.

CHECK AIR BAG MODULE AND SEAT BELT PRE-TENSIONER     

Check the deployment of air bag module and seat belt pre-tensioner.

Is air bag module deployed?

YES

>> Replace the malfunctioning parts.

NO

>> GO TO 2.

2.

CHECK AIR BAG FUSE

Check 10 A fuse [No.2, located in fuse block (J/B)].

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace the fuse.

3.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace harness connectors.

4.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace wiring harness.

5.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Exploded View"

.

2.

Check air bag warning lamp operation.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 6.

6.

REPLACE COMBINATION METER

1.

Replace combination meter. Refer to 

MWI-70, "Exploded View"

.

2.

Check air bag warning lamp operation.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 1.

Revision: 2012 October

2013 Murano CrossCabriolet

SRC-178

< SYMPTOM DIAGNOSIS >

SRS AIR BAG WARNING LAMP DOES NOT TURN ON

SRS AIR BAG WARNING LAMP DOES NOT TURN ON

Diagnosis Procedure

INFOID:0000000008461973

1.

CHECK  COMBINATION METER POWER SUPPLY AND GROUND CIRCUIT

Check conbination meter unit power supply and ground circuit. Refer to

MWI-47, "COMBINATION METER :

Diagnosis Procedure"

 .

Is  the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.  

2.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace harness connectors.

3.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace wiring harness.

4.

CHECK AIR BAG DIAGNOSIS SENSOR UNIT

Disconnect air bag diagnosis sensor unit connector and turn ignition switch ON.

Does air bag warning lamp turn ON?

YES

>> Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Exploded View"

.

NO

>> Replace combination meter. Refer to 

MWI-70, "Removal and Installation"

.

Revision: 2012 October

2013 Murano CrossCabriolet

SRS AIR BAG WARNING LAMP BLINKS

SRC-179

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

SRS AIR BAG WARNING LAMP BLINKS

Diagnosis Procedure

INFOID:0000000008461974

1.

CHECK BATTERY

Check battery. Refer to 

PG-101, "How to Handle Battery"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace malfunctioning parts.

2.

REPLACE OCCUPANT CLASSIFICATION SYSTEM CONTROL UNIT

1.

Replace occupant classification system control unit. Refer to 

SR-33, "Removal and Installation"

.

2.

Check air bag warning lamp operation.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 3.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-30, "Exploded View"

.

2.

Check air bag warning lamp operation.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 1.

Revision: 2012 October

2013 Murano CrossCabriolet

ST-1

STEERING

C

D

E

F

H

I

J

K

L

M

SECTION 

ST

A

B

ST

N

O

P

CONTENTS

STEERING SYSTEM

PRECAUTION ...............................................

3

PRECAUTIONS ...................................................

3

Precaution for Supplemental Restraint System 
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...................................................................

3

Precaution for Battery Service  ..................................

3

Service Notice or Precautions for Steering System 

......

3

PREPARATION ............................................

4

PREPARATION ...................................................

4

Special Service Tools ................................................

4

Commercial Service Tools  ........................................

5

SYSTEM DESCRIPTION  ..............................

7

COMPONENT PARTS  ........................................

7

Component Parts Location (Heated Steering 
Wheel) .......................................................................

7

Component Description (Heated Steering Wheel) 

......

7

Heated Steering Wheel  .............................................

7

Heated Steering Wheel Switch  .................................

7

Heated Steering Wheel Relay ...................................

7

SYSTEM ..............................................................

8

System Description (Heated Steering Wheel) ...........

8

WIRING DIAGRAM  .......................................

9

HEATED STEERING WHEEL  .............................

9

Wiring Diagram  .........................................................

9

BASIC INSPECTION  ...................................

10

DIAGNOSIS AND REPAIR WORK FLOW  ........

10

WorkFlow (Heated Steering Wheel) ........................

10

STEERING WHEEL ............................................

11

Inspection ................................................................

11

DTC/CIRCUIT DIAGNOSIS  .........................

13

HEATED STEERING WHEEL SYSTEM  ...........

13

Component Function Check  ....................................

13

Diagnosis Procedure  ...............................................

13

Component Inspection (Heated Steering Wheel) ....

15

Component Inspection (Heated Steering Wheel 
Relay) ......................................................................

16

HEATED STEERING WHEEL SWITCH INDI-
CATOR LAMP ...................................................

17

Component Function Check  ....................................

17

Diagnosis Procedure  ...............................................

17

Component Inspection (Heated Steering Wheel 
Relay) ......................................................................

19

SYMPTOM DIAGNOSIS  ..............................

20

HEATED STEERING WHEEL SYSTEM DOES 
NOT ACTIVATE  ................................................

20

Description ...............................................................

20

Diagnosis Procedure  ...............................................

20

HEATED STEERING WHEEL SWITCH INDI-
CATOR LAMP DOES NOT TURN ON ..............

23

Description ...............................................................

23

Diagnosis Procedure  ...............................................

23

NOISE, VIBRATION AND HARSHNESS 
(NVH) TROUBLESHOOTING  ...........................

26

NVH Troubleshooting Chart  ....................................

26

PERIODIC MAINTENANCE  ........................

27

POWER STEERING FLUID  ..............................

27

Inspection ................................................................

27

STEERING WHEEL  ..........................................

29

Inspection ................................................................

29

REMOVAL AND INSTALLATION  ...............

30

STEERING WHEEL  ..........................................

30

Exploded View .........................................................

30

Revision: 2012 October

2013 Murano CrossCabriolet

ST-2

Removal and Installation  ........................................

30

STEERING COLUMN  ........................................

31

Exploded View  ........................................................

31

Removal and Installation  ........................................

31

Inspection ...............................................................

32

LOWER SHAFT  .................................................

34

Exploded View  ........................................................

34

Removal and Installation  ........................................

34

Inspection ...............................................................

36

STEERING GEAR AND LINKAGE ....................

37

Exploded View  ........................................................

37

Removal and Installation  ........................................

38

Disassembly and Assembly ....................................

40

Inspection ...............................................................

45

POWER STEERING OIL PUMP  ........................

47

Exploded View  ........................................................

47

Removal and Installation  ........................................

48

Disassembly and Assembly ....................................

48

Inspection ...............................................................

51

HYDRAULIC LINE .............................................

53

Exploded View  ........................................................

53

Removal and Installation .........................................

53

HEATED STEERING WHEEL SWITCH  ............

55

Removal and Installation .........................................

55

SERVICE DATA AND SPECIFICATIONS 
(SDS) ..........................................................

56

SERVICE DATA AND SPECIFICATIONS 
(SDS) .................................................................

56

General Specifications  ............................................

56

Steering Wheel Axial End Play and Play  ................

56

Steering Wheel Turning Force  ................................

56

Steering Angle  ........................................................

56

Steering Column Length  .........................................

56

Steering Column Mounting Dimensions ..................

56

Steering Column Operating Range .........................

56

Lower Shaft Length .................................................

57

Rack Sliding Force ..................................................

57

Rack Stroke  ............................................................

57

Socket Swing Force and Rotating Torque  ..............

57

Socket Axial End Play .............................................

57

Inner Socket Length ................................................

57

Relief Oil Pressure  ..................................................

57

Revision: 2012 October

2013 Murano CrossCabriolet

PRECAUTIONS

ST-3

< PRECAUTION >

C

D

E

F

H

I

J

K

L

M

A

B

ST

N

O

P

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT 
PRE-TENSIONER"

INFOID:0000000008461702

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.

WARNING:

Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.

• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-

vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the

ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.

• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

Precaution for Battery Service

INFOID:0000000008461703

Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.

Service Notice or Precautions for Steering System

INFOID:0000000008461704

• In case of removing steering gear assembly, make the final tightening with grounded and unloaded vehicle

condition, and then check wheel alignment.

• Observe the following precautions when disassembling.
- Before disassembly, thoroughly clean the outside of the unit.
- Disassembly should be done in a clean work area. It is important to prevent the internal parts from becoming

contaminated by dirt or other foreign matter.

- For easier and proper assembly, place disassembled parts in order on a parts rack.
- Use nylon cloth or paper towels to clean the parts; common shop rags can leave lint that might interfere with

their operation.

- Never reuse non-reusable parts.
- Before assembling, apply the specified grease to the directed parts.

Revision: 2012 October

2013 Murano CrossCabriolet

ST-4

< PREPARATION >

PREPARATION

PREPARATION

PREPARATION

Special Service Tools

INFOID:0000000008461705

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Tool number
(Kent-Moore No.)
Tool name

Description

ST27180001
(J-25726-A)
Steering wheel puller

Removing steering wheel

ST3127S000
(J-25765-A)
Preload gauge

• Measuring steering wheel turning torque
• Measuring steering column rotating torque
• Measuring ball joint rotating torque
• Measuring pinion rotating torque

KV48104400
(

—

)

Teflon ring correcting tool
a: 50 mm (1.97 in) dia.
b: 36 mm (1.42 in) dia.
c: 100 mm (3.94 in)

Installing rack Teflon ring

KV48103400
(

—

)

Preload adapter

Measuring rotating torque

ST35300000
(

—

)

Drift
a: 45.1 mm (1.776 in) dia.
b: 59.0 mm (2.323 in) dia.

Installing oil pump oil seal

ZZA0819D

ZZA0806D

S-NT550

ZZA0824D

ZZA0881D

Revision: 2012 October

2013 Murano CrossCabriolet

PREPARATION

ST-5

< PREPARATION >

C

D

E

F

H

I

J

K

L

M

A

B

ST

N

O

P

Commercial Service Tools

INFOID:0000000008461706

KV48103500
(J-26357)
Oil pressure gauge

Measuring oil pump relief pressure

KV48102500
(J-33914)
Oil pressure gauge adapter

Measuring oil pump relief pressure

Tool number
(Kent-Moore No.)
Tool name

Description

S-NT547

S-NT542

Tool name

Description

Power tool

Loosening bolts and nuts

Ball joint remover

Removing steering outer socket

Open head

Tightening end cover assembly

PBIC0190E

S-NT146

ZZA0822D

Revision: 2012 October

2013 Murano CrossCabriolet