Murano Cross Cabriolet Z51 (2013 year). Manual - part 71

DOOR KEY CYLINDER SWITCH

PWC-45

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

Is the inspection result normal?

YES

>> Replace power window main switch. Refer to 

PWC-66, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK DOOR KEY CYLINDER SWITCH GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Check continuity between front door lock assembly (driver side) (door key cylinder switch) harness con-
nector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK DOOR KEY CYLINDER SWITCH

Refer to 

PWC-45, "Component Inspection"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

NO

>> Replace front door lock assembly (driver side) (door key cylinder switch).

Component Inspection

INFOID:0000000008463253

1.

CHECK DOOR KEY CYLINDER SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect front door lock assembly (driver side) (door key cylinder switch) connector.

3.

Check front door lock assembly (driver side) (door key cylinder switch) terminals under the following con-
ditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace front door lock assembly (driver side) (door key cylinder switch).

Power window main switch

Ground

Continuity 

Connector

Terminal

D5

4

Not existed

6

Front door lock assembly (driver side)

(door key cylinder switch)

Ground

Continuity 

Connector

Terminal

D9

4

Existed

Terminal

Condition

Continuity

5

4

Unlock

Existed

Neutral / Lock

Not existed

6

Lock

Existed

Neutral / Unlock

Not existed

Revision: 2012 October

2013 Murano CrossCabriolet

PWC-46

< DTC/CIRCUIT DIAGNOSIS >

POWER WINDOW SERIAL LINK

POWER WINDOW SERIAL LINK

POWER WINDOW MAIN SWITCH

POWER WINDOW MAIN SWITCH : Diagnosis Procedure

INFOID:0000000008463254

1.

CHECK POWER WINDOW SWITCH OUTPUT SIGNAL

1.

 Turn ignition switch ON.

2.

Check signal between power window main switch harness connector and ground using an oscilloscope.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

NO

>> GO TO 2.

2.

CHECK POWER WINDOW SERIAL LINK SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect power window main switch connector.

3.

Turn ignition switch ON.

4.

Check voltage between power window main switch harness connector and ground.

Is the measurement value within the specification?

YES

>> Replace power window main switch. Refer to 

PWC-66, "Removal and Installation"

. 

NO

>> GO TO 3.

3.

CHECK POWER WINDOW SERIAL LINK CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect soft top control unit connector.

3.

Check continuity between soft top control unit harness connector and power window main switch harness
connector.

4.

Check continuity between soft top control unit harness connector and ground.

Is the inspection result normal?

(+)

(–)

Signal

(Reference value)

Power window main switch

Connector

Terminal

D5

14

Ground

JPMIA0013GB

(+)

(–)

Voltage (V)

(Approx.)

Power window main switch

Connector

Terminal 

D5

14

Ground

12

Soft top control unit

Power window main switch

Continuity

Connector

Terminal

Connector

Terminal

B323

19

D5

14

Existed

Soft top control unit

Ground

Continuity 

Connector

Terminal

B323

19

Not existed

Revision: 2012 October

2013 Murano CrossCabriolet

POWER WINDOW SERIAL LINK

PWC-47

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

YES

>> Replace soft top control unit. Refer to 

RF-229, "Removal and Installation"

. 

NO

>> Repair or replace harness.

FRONT POWER WINDOW SWITCH (PASSENGER SIDE)

FRONT POWER WINDOW SWITCH (PASSENGER SIDE) : Diagnosis Procedure

INFOID:0000000008463255

1.

CHECK POWER WINDOW SWITCH OUTPUT SIGNAL

1.

Turn ignition switch ON.

2.

Check signal between front power window switch (passenger side) harness connector and ground using
an oscilloscope.

Is the inspection result normal?

YES

>> Replace front power window switch (passenger side). Refer to 

PWC-66, "Removal and Installa-

tion"

. 

NO

>> GO TO 2.

2.

CHECK POWER WINDOW SERIAL LINK CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect power window main switch connector and front power window switch (passenger side) con-
nector.

3.

Check continuity between power window main switch harness connector and front power window switch
(passenger side) harness connector.

4.

Check continuity between power window main switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace power window main switch. Refer to 

PWC-66, "Removal and Installation"

. 

NO

>> Repair or replace harness.

REAR POWER WINDOW SWITCH LH

REAR POWER WINDOW SWITCH LH : Diagnosis Procedure

INFOID:0000000008463256

1.

CHECK POWER WINDOW SWITCH OUTPUT SIGNAL

1.

Turn ignition switch ON.

2.

Check signal between rear power window switch LH harness connector and ground using an oscillo-
scope.

(+)

(

−

)

Signal

(Reference value)

Front power window switch (passenger side)

Connector

Terminal

D45

16

Ground

JPMIA0013GB

Power window main switch

Front power window switch (passenger side)

Continuity

Connector

Terminal

Connector

Terminal

D5

14

D45

16

Existed

Power window main switch

Ground

Continuity 

Connector

Terminal

D5

14

Not existed

Revision: 2012 October

2013 Murano CrossCabriolet

PWC-48

< DTC/CIRCUIT DIAGNOSIS >

POWER WINDOW SERIAL LINK

Is the inspection result normal?

YES

>> Replace rear power window switch LH. Refer to 

PWC-66, "Removal and Installation"

. 

NO

>> GO TO 2.

2.

CHECK POWER WINDOW SERIAL LINK CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect power window main switch connector and rear power window switch LH connector.

3.

Check continuity between power window main switch harness connector and rear power window switch
LH harness connector.

4.

Check continuity between power window main switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace power window main switch. Refer to 

PWC-66, "Removal and Installation"

. 

NO

>> Repair or replace harness.

REAR POWER WINDOW SWITCH RH

REAR POWER WINDOW SWITCH RH : Diagnosis Procedure

INFOID:0000000008463257

1.

CHECK POWER WINDOW SWITCH OUTPUT SIGNAL

1.

Turn ignition switch ON.

2.

Check signal between rear power window switch RH harness connector and ground using an oscillo-
scope.

Is the inspection result normal?

(+)

(

−

)

Signal

(Reference value)

Rear power window switch LH

Connector

Terminal

B42

16

Ground

JPMIA0013GB

Power window main switch

Rear power window switch LH

Continuity

Connector

Terminal

Connector

Terminal

D5

14

B42

16

Existed

Power window main switch

Ground

Continuity 

Connector

Terminal

D5

14

Not existed

(+)

(

−

)

Signal

(Reference value)

Rear power window switch RH

Connector

Terminal

B222

16

Ground

JPMIA0013GB

Revision: 2012 October

2013 Murano CrossCabriolet

POWER WINDOW SERIAL LINK

PWC-49

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

YES

>> Replace rear power window switch RH. Refer to 

PWC-66, "Removal and Installation"

. 

NO

>> GO TO 2.

2.

CHECK POWER WINDOW SERIAL LINK CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect power window main switch connector and rear power window switch RH connector.

3.

Check continuity between power window main switch harness connector and rear power window switch
RH harness connector.

4.

Check continuity between power window main switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace power window main switch. Refer to 

PWC-66, "Removal and Installation"

. 

NO

>> Repair or replace harness.

Power window main switch

Rear power window switch RH

Continuity

Connector

Terminal

Connector

Terminal

D5

14

B222

16

Existed

Power window main switch

Ground

Continuity 

Connector

Terminal

D5

14

Not existed

Revision: 2012 October

2013 Murano CrossCabriolet

PWC-50

< DTC/CIRCUIT DIAGNOSIS >

DOOR SWITCH

DOOR SWITCH

DRIVER SIDE

DRIVER SIDE : Component Function Check

INFOID:0000000008463258

1.

CHECK FUNCTION

Check that automatic adjusting function operates normally when driver side door is opened.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Refer to 

PWC-50, "DRIVER SIDE : Diagnosis Procedure"

.

DRIVER SIDE : Diagnosis Procedure

INFOID:0000000008463259

1.

CHECK FRONT DOOR SWITCH (DRIVER SIDE)

Refer to 

DLK-55, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace malfunctioning parts.

2.

CHECK FRONT DOOR SWITCH (DRIVER SIDE) CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect front door switch (driver side) connector and power window main switch connector.

3.

Check continuity between front door switch (driver side) harness connector and power window main
switch harness connector.

4.

Check continuity between front door switch (driver side) harness connector and ground.

Is the inspection result normal?

YES

>> Replace power window main switch. Refer to 

PWC-66, "Removal and Installation"

.

NO

>> Replace or repair harness.

PASSENGER SIDE

PASSENGER SIDE : Component Function Check

INFOID:0000000008463260

1.

CHECK FUNCTION

Check that automatic adjusting function operates normally when passenger side door is opened.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Refer to 

PWC-50, "PASSENGER SIDE : Diagnosis Procedure"

.

PASSENGER SIDE : Diagnosis Procedure

INFOID:0000000008463261

1.

CHECK FRONT DOOR SWITCH (PASSENGER SIDE)

Refer to 

DLK-55, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace malfunctioning parts.

Front door switch (driver side)

Power window main switch

Continuity

Connector

Terminal

Connector

Terminal

B32

3

D5

5

Existed

Front door switch (driver side)

Ground

Continuity

Connector

Terminal

B32

3

Not existed

Revision: 2012 October

2013 Murano CrossCabriolet

DOOR SWITCH

PWC-51

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

2.

CHECK FRONT DOOR SWITCH (PASSENGER SIDE) CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect front door switch (passenger side) connector and front power window switch (passenger side)
connector.

3.

Check continuity between front door switch (passenger side) harness connector and front power window
switch (passenger side) harness connector.

4.

Check continuity between front door switch (passenger side) harness connector and ground.

Is the inspection result normal?

YES

>> Replace front power window switch (passenger side). Refer to 

PWC-66, "Removal and Installa-

tion"

.

NO

>> Replace or repair harness.

Front door switch (passenger side)

Front power window switch (passenger side)

Continuity

Connector

Terminal

Connector

Terminal

B233

3

D45

14

Existed

Front door switch (passenger side)

Ground

Continuity

Connector

Terminal

B233

3

Not existed

Revision: 2012 October

2013 Murano CrossCabriolet

PWC-52

< SYMPTOM DIAGNOSIS >

NONE OF THE POWER WINDOWS CAN BE OPERATED USING ANY SWITCH

SYMPTOM DIAGNOSIS

NONE OF THE POWER WINDOWS CAN BE OPERATED USING ANY
SWITCH

Diagnosis Procedure

INFOID:0000000008463262

1.

CHECK DTC WITH SOFT TOP CONTROL UNIT

Check that DTC is not detected with soft top control unit.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Refer to 

RF-57, "DTC Index"

.

2.

CHECK BCM POWER SUPPLY AND GROUND CIRCUIT

Check BCM power supply and ground circuit.
Refer to 

BCS-70, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CHECK POWER WINDOW MAIN SWITCH POWER SUPPLY AND GROUND CIRCUIT

Check power window main switch power supply and ground circuit.
Refer to 

PWC-28, "POWER WINDOW MAIN SWITCH : Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning parts.

4.

CHECK POWER WINDOW MAIN SWITCH SERIAL LINK CIRCUIT

Check power window main switch serial link circuit.
Refer to 

PWC-46, "POWER WINDOW MAIN SWITCH : Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning parts.

5.

REPLACE POWER WINDOW MAIN SWITCH

1.

Replace power window main switch. Refer to 

PWC-66, "Removal and Installation"

.

2.

Confirm the operation after replacement.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

Revision: 2012 October

2013 Murano CrossCabriolet

DRIVER SIDE POWER WINDOW DOES NOT OPERATE

PWC-53

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

DRIVER SIDE POWER WINDOW DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000008463263

1.

CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE) CIRCUIT

Check front power window motor (driver side) circuit. 
Refer to 

PWC-31, "DRIVER SIDE : Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

NO

>> GO TO 1. 

Revision: 2012 October

2013 Murano CrossCabriolet

PWC-54

< SYMPTOM DIAGNOSIS >

FRONT PASSENGER SIDE POWER WINDOW DOES NOT OPERATE

FRONT PASSENGER SIDE POWER WINDOW DOES NOT OPERATE

WHEN BOTH POWER WINDOW MAIN SWITCH AND FRONT POWER WINDOW
SWITCH ARE OPERATED

WHEN BOTH POWER WINDOW MAIN SWITCH AND FRONT POWER WINDOW 
SWITCH ARE OPERATED : Diagnosis Procedure

INFOID:0000000008463264

1.

CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) POWER SUPPLY AND GROUND CIR-

CUIT

Check front power window switch (passenger side) power supply and ground circuit. 
Refer to 

PWC-29, "FRONT POWER WINDOW SWITCH (PASSENGER SIDE) : Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK FRONT POWER WINDOW MOTOR (PASSENGER SIDE) CIRCUIT

Check front power window motor (passenger side) circuit. 
Refer to 

PWC-32, "PASSENGER SIDE : Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

NO

>> GO TO 1.

WHEN FRONT POWER WINDOW SWITCH (PASSENGER SIDE) IS OPERATED

WHEN FRONT POWER WINDOW SWITCH (PASSENGER SIDE) IS OPERATED : 
Diagnosis Procedure

INFOID:0000000008463265

1.

REPLACE FRONT POWER WINDOW SWITCH (PASSENGER SIDE)

Replace front power window switch (passenger side).
Refer to 

PWC-66, "Removal and Installation"

.

>> INSPECTION END

WHEN POWER WINDOW MAIN SWITCH IS OPERATED

WHEN POWER WINDOW MAIN SWITCH IS OPERATED : Diagnosis Procedure

INFOID:0000000008463266

1.

CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) SERIAL LINK CIRCUIT

Check front power window switch (passenger side) serial link circuit. 
Refer to 

PWC-47, "FRONT POWER WINDOW SWITCH (PASSENGER SIDE) : Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

NO

>> GO TO 1.

Revision: 2012 October

2013 Murano CrossCabriolet

REAR LH SIDE POWER WINDOW DOES NOT OPERATE

PWC-55

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

REAR LH SIDE POWER WINDOW DOES NOT OPERATE

WHEN BOTH POWER WINDOW MAIN SWITCH AND REAR POWER WINDOW
SWITCH LH ARE OPERATED

WHEN BOTH POWER WINDOW MAIN SWITCH AND REAR POWER WINDOW 
SWITCH LH ARE OPERATED : Diagnosis Procedure

INFOID:0000000008463267

1.

CHECK REAR POWER WINDOW SWITCH LH POWER SUPPLY AND GROUND CIRCUIT

Check rear power window switch LH power supply and ground circuit. 
Refer to 

PWC-29, "REAR POWER WINDOW SWITCH : Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK REAR POWER WINDOW MOTOR LH 

Check rear power window motor LH. 
Refer to 

PWC-33, "REAR LH : Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

NO

>> GO TO 1.

WHEN REAR POWER WINDOW SWITCH LH IS OPERATED

WHEN REAR POWER WINDOW SWITCH LH IS OPERATED : Diagnosis Procedure

INFOID:0000000008463268

1.

REPLACE REAR POWER WINDOW SWITCH LH

Replace rear power window switch LH.
Refer to 

PWC-66, "Removal and Installation"

.

>> INSPECTION END

WHEN POWER WINDOW MAIN SWITCH IS OPERATED

WHEN POWER WINDOW MAIN SWITCH IS OPERATED : Diagnosis Procedure

INFOID:0000000008463269

1.

CHECK REAR POWER WINDOW SWITCH LH SERIAL LINK CIRCUIT

Check rear power window switch LH serial link circuit.
Refer to 

PWC-47, "REAR POWER WINDOW SWITCH LH : Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

NO

>> GO TO 1.

Revision: 2012 October

2013 Murano CrossCabriolet

PWC-56

< SYMPTOM DIAGNOSIS >

REAR RH SIDE POWER WINDOW DOES NOT OPERATE

REAR RH SIDE POWER WINDOW DOES NOT OPERATE

WHEN BOTH POWER WINDOW MAIN SWITCH AND REAR POWER WINDOW
SWITCH RH ARE OPERATED

WHEN BOTH POWER WINDOW MAIN SWITCH AND REAR POWER WINDOW 
SWITCH RH ARE OPERATED : Diagnosis Procedure

INFOID:0000000008463270

1.

CHECK REAR POWER WINDOW SWITCH RH POWER SUPPLY AND GROUND CIRCUIT

Check rear power window switch RH power supply and ground circuit. 
Refer to 

PWC-29, "REAR POWER WINDOW SWITCH : Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK REAR POWER WINDOW MOTOR RH

Check rear power window motor RH. 
Refer to 

PWC-33, "REAR RH : Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

NO

>> GO TO 1.

WHEN REAR POWER WINDOW SWITCH RH IS OPERATED

WHEN REAR POWER WINDOW SWITCH RH IS OPERATED : Diagnosis Procedure

INFOID:0000000008463271

1.

REPLACE REAR POWER WINDOW SWITCH RH

Replace rear power window switch RH.
Refer to 

PWC-66, "Removal and Installation"

.

>> INSPECTION END

WHEN POWER WINDOW MAIN SWITCH IS OPERATED

WHEN POWER WINDOW MAIN SWITCH IS OPERATED : Diagnosis Procedure

INFOID:0000000008463272

1.

CHECK REAR POWER WINDOW SWITCH RH SERIAL LINK CIRCUIT

Check rear power window switch RH serial link circuit.
Refer to 

PWC-48, "REAR POWER WINDOW SWITCH RH : Diagnosis Procedure"

.

Is the inspection result normal?

YES

>>  GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

NO

>> GO TO 1.

Revision: 2012 October

2013 Murano CrossCabriolet

AUTO OPERATION DOES NOT OPERATE BUT MANUAL OPERATES NORMAL-

LY

PWC-57

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

AUTO OPERATION DOES NOT OPERATE BUT MANUAL OPERATES
NORMALLY

DRIVER SIDE

DRIVER SIDE : Diagnosis Procedure

INFOID:0000000008463273

1.

PERFORM INITIALIZATION PROCEDURE

Initialization procedure is executed and operation is confirmed.
Refer to 

PWC-26, "Work Procedure"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK ENCODER CIRCUIT (DRIVER SIDE)

Check encoder circuit (driver side).
Refer to 

PWC-35, "DRIVER SIDE : Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

REPLACE POWER WINDOW MAIN SWITCH

1.

Replace power window main switch. Refer to 

PWC-66, "Removal and Installation"

.

2.

Confirm the operation after replacement.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

PASSENGER SIDE

PASSENGER SIDE : Diagnosis Procedure

INFOID:0000000008463274

1.

PERFORM INITIALIZATION PROCEDURE

Initialization procedure is executed and operation is confirmed.
Refer to 

PWC-26, "Work Procedure"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK ENCODER CIRCUIT (PASSENGER SIDE)

Check encoder circuit (passenger side).
Refer to 

PWC-37, "PASSENGER SIDE : Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

REPLACE FRONT POWER WINDOW SWITCH (PASSENGER SIEDE)

1.

Replace front power window switch (passenger side). Refer to 

PWC-66, "Removal and Installation"

.

2.

Confirm the operation after replacement.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

REAR LH

Revision: 2012 October

2013 Murano CrossCabriolet

PWC-58

< SYMPTOM DIAGNOSIS >

AUTO OPERATION DOES NOT OPERATE BUT MANUAL OPERATES NORMAL-

LY

REAR LH : Diagnosis Procedure

INFOID:0000000008463275

1.

CHECK ENCODER (REAR LH) CIRCUIT

Check encoder (rear LH) circuit.
Refer to 

PWC-39, "REAR LH : Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

REPLACE REAR POWER WINDOW SWITCH LH

1.

Replace rear power window switch LH. Refer to 

PWC-66, "Removal and Installation"

.

2.

Confirm the operation after replacement.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

REAR RH

REAR RH : Diagnosis Procedure

INFOID:0000000008463276

1.

CHECK ENCODER (REAR RH) CIRCUIT

Check encoder (rear RH) circuit. 
Refer to 

PWC-41, "REAR RH : Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

REPLACE REAR POWER WINDOW SWITCH RH

1.

Replace rear power window switch RH. Refer to 

PWC-66, "Removal and Installation"

.

2.

Confirm the operation after replacement.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

Revision: 2012 October

2013 Murano CrossCabriolet

ANTI-PINCH FUNCTION DOES NOT OPERATE NORMALLY

PWC-59

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

ANTI-PINCH FUNCTION DOES NOT OPERATE NORMALLY

Diagnosis Procedure

INFOID:0000000008463277

1.

CHECK POWER WINDOW AUTO OPERATION

Check AUTO operation when anti-pinch function does not operate.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Refer to 

PWC-57, "DRIVER SIDE : Diagnosis Procedure"

 (driver side), 

PWC-57, "PASSENGER

SIDE : Diagnosis Procedure"

 (passenger side).

2.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

NO

>> GO TO 1.

Revision: 2012 October

2013 Murano CrossCabriolet

PWC-60

< SYMPTOM DIAGNOSIS >

AUTOMATIC WINDOW ADJUSTING FUNCTION DOES NOT OPERATE

AUTOMATIC WINDOW ADJUSTING FUNCTION DOES NOT OPERATE

DRIVER SIDE

DRIVER SIDE : Diagnosis Procedure

INFOID:0000000008463278

1.

CHECK AUTO UP OPERATION

Check AUTO operation when automatic window adjusting function does not operate.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Refer to 

PWC-57, "DRIVER SIDE : Diagnosis Procedure"

.

2.

CHECK FRONT DOOR SWITCH (DRIVER SIDE)

Check front door switch (driver side).
Refer to 

PWC-50, "DRIVER SIDE : Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

REPLACE POWER WINDOW MAIN SWITCH

1.

Replace power window main switch. Refer to 

PWC-66, "Removal and Installation"

.

2.

Confirm the operation after replacement.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

PASSENGER SIDE

PASSENGER SIDE : Diagnosis Procedure

INFOID:0000000008463279

1.

CHECK AUTO UP OPERATION

Check AUTO operation when automatic window adjusting function does not operate.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Refer to 

PWC-57, "PASSENGER SIDE : Diagnosis Procedure"

.

2.

CHECK FRONT DOOR SWITCH (PASSENGER SIDE)

Check front door switch (passenger side).
Refer to 

PWC-50, "PASSENGER SIDE : Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

REPLACE FRONT POWER WINDOW SWITCH (PASSENGER SIDE)

1.

Replace front power window switch (passenger side). Refer to 

PWC-66, "Removal and Installation"

.

2.

Confirm the operation after replacement.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

Revision: 2012 October

2013 Murano CrossCabriolet