Murano Cross Cabriolet Z51 (2013 year). Manual - part 44

GW-18

< REMOVAL AND INSTALLATION >

QUARTER WINDOW GLASS

14. Remove quarter window guide rail mounting nuts (A) and nuts

(B), and then remove quarter window guide rail.

15. Remove quarter window front guide channel (1) mounting nut

(A) and (B), then remove quarter window front guide channel.

INSTALLATION

Install in the reverse order of removal.

INSPECTION AFTER REMOVAL

Quarter window glass regulator

Check that the quarter window glass regulator assembly for the following. If a failure is detected, replace or
grease it.

• Wire wear 
• Quarter window glass regulator assembly deformation
• Grease body condition on each sliding part
The arrows in the figure grease show the application points of the multi-purpose grease.

Quarter window rear guide rail and front guide channel

JMKIA8387ZZ

JMKIA8564ZZ

JMKIA8389ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

QUARTER WINDOW GLASS

GW-19

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

GW

N

O

P

Check that the quarter window (1) rear guide rail (2) and guide chan-
nel (3) for the following. If a failure is detected, replace or grease it.
• Quarter window rear guide rail or guide channel deformation
• Grease body condition on each sliding part
The arrows in the figure show the application points of the multi-pur-
pose grease.

Disassembly and Assembly

INFOID:0000000008462460

DISASSEMBLY

1.

Remove quarter window regulator assembly. Refer to 

GW-16, "Removal and Installation"

.

2.

Remove the quarter window regulator motor from quarter window glass regulator assembly.

ASSEMBLY

Assemble in the reverse order of disassembly.

Inspection and Adjustment

INFOID:0000000008462461

FITTING ADJUSTMENT

CAUTION:

Adjust door inner stabilizer assembly after every quarter window glass removal before adjusting the
glass.

Door inner stabilizer assembly adjustment procedure.

1.

Loose door inner stabilizer assembly adjusting nut (A).

2.

Set quarter window glass (2) to the position just before fully-closed (the status that glass stopper does not
contact with inner stabilizer (1)). 

3.

Contact outside surface of quarter window glass to outside molding while lightly pressing door inner stabi-
lizer assembly adjusting bolts (A) as shown by the arrows in the figure to inside surface of quarter window
glass (2). 

JMKIA8599ZZ

Glass mounting nut

Tightening torque

: 7.0 N·m (0.71 kg-m, 62 in-lb)

JMKIA8566ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

GW-20

< REMOVAL AND INSTALLATION >

QUARTER WINDOW GLASS

4.

Tighten bolt on upper end of inner stabilizer to the specified torque and check that door inner stabilizer is
parallel to glass surface.

Preparation for adjustment 

1.

Apply protective tape (A) as shown on the figure above in door glass and quarter window glass.

2.

Fully close the door window glass and the quarter window glass, and mark each edge of the weather-strip
on the glass as shown by the points (B).

3.

Measure the clearances (C), (D), and (E) and check that there are in the range provided in the figure
above. If not then proceed to the adjustment of quarter window glass by following the steps below.

Inclination Adjustment

JMKIA8395ZZ

1.

Door glass assembly

2.

Quarter window glass

C

: 4.0 (0.157)

D

: 9.8 (0.386)

E

: 9.8 (0.386)

Unit: mm (in)

Revision: 2012 October

2013 Murano CrossCabriolet

QUARTER WINDOW GLASS

GW-21

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

GW

N

O

P

As shown in the figure, quarter glass adjustment can be made in four
different directions.
• (1): Clockwise rotation / Counterclockwise rotation direction
• (2): Upper / lower direction
• (3): Outer / inner direction
• (4): Front / rear direction

1.

Clockwise rotation / Counterclockwise rotation adjustment.

a.

Loose quarter window door regulator sub channel (1) adjusting
nut (B).

b.

Slide the sub channel upper to rotate quarter window glass to
the left (anti-clockwise)

c.

Slide the sub channel lower to rotate quarter window glass to the
right (clockwise)

2.

Upper/lower direction adjustment.

a.

Operate quarter window glass motor switch to lower the quarter window glass (1) if it is was fully closed.

b.

Loose adjusting nuts (A) or (B) to adjust the nuts as shown by the figure to upper or lower the glass.

c.

When the right position is find, tighten adjusting nuts to the specified torque.

JMKIA8565ZZ

JMKIA8567ZZ

JMKIA8568ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

GW-22

< REMOVAL AND INSTALLATION >

QUARTER WINDOW GLASS

3.

Outer / inner direction adjustment (Upper glass).

a.

Adjust quarter window glass and retainer to the specified dimension using adjusting bolts (A) and (B) of
quarter window rear guide rail and quarter window front guide channel.

b.

Upper end of glass opens toward outside for the adjusting bolt clockwise rotation.

c.

Upper end of glass opens toward inside for the adjusting bolt counterclockwise rotation.

d.

Adjust using either rear bolt out of the two adjusting bolts (A) and (B). After tilt is adjusted, slightly contact
remaining adjusting bolt to inner panel, and then tighten flange nut to the specified torque.
NOTE:
Adjust so that protrusions of the 2 adjusting bolts are the same.

4.

Front / rear direction adjustment.

a.

Adjust the quarter window glass with quarter window guide rail
adjusting bolt (A) and (B). 

b.

When adjusting the quarter window glass toward front, lower the
glass at about 5 to 10 mm (0.197 to 0.394in) of space between
panel side stopper (1) and glass side stopper (2).

: Vehicle front

JMKIA8569ZZ

: Vehicle front

JMKIA8570ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

QUARTER WINDOW GLASS

GW-23

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

GW

N

O

P

Fitting between door glass and quarter window glass

1.

Fully close door glass and quarter window glass.

2.

Check that both upper edges of door glass and quarter window glass are the same level.

3.

Check that the clearance between door glass and quarter window glass is in the range of E.

4.

Check that the clearances between the weather-strip and quarter window glass is in the range of C and D.

Fitting inspection

• Check that the overlap length with the body side weather-strip is maintained on the glass.
• Check that clearance between door glass and quarter window glass sash is parallel when door glass is

closed.

• Adjust sub channel and set quarter window glass to the normal position, when clearance between front door

glass and quarter sash is not parallel. At this time, adjustment for stopper of panel side is necessary again.

• When adjusting fitting of glass, open glass once, fully close it, and then check the fitting while glass is fully

closed.

• Check opening and closing trace of quarter window glass.
• Check that closing trace of quarter window glass is constant just before glass is fully closed while soft top is

open.

• Open and close quarter window glass and check that operation is normal, for each condition where soft top

is open or closed, or door glass is open or closed.

JMKIA8394ZZ

1.

Door glass assembly

2.

Quarter window glass

C

: 9.8 (0.386)

D

: 10.6 (0.417)

E

: 8.5 (0.335)

Unit: mm (in)

Revision: 2012 October

2013 Murano CrossCabriolet

GW-24

< REMOVAL AND INSTALLATION >

QUARTER WINDOW GLASS

• Particularly, check that door glass does not contact to quarter sash when quarter window glass is operated

to the fully closed position while soft top is open status and front door glass is closed.

Water Leakage Test

Visually check for water leakage after adjustment. Refer to 

RF-71, "Water Leakage Test"

.

Revision: 2012 October

2013 Murano CrossCabriolet

DOOR GLASS

GW-25

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

GW

N

O

P

DOOR GLASS

Exploded View

INFOID:0000000008462462

Removal and Installation

INFOID:0000000008462463

REMOVAL

1.

Remove door finisher. Refer to 

INT-13, "Removal and Installation"

.

2.

Remove door finisher inside seal.

3.

Remove door module assembly hole cover seal.

1.    Door panel assembly

2.

Door glass

3.

Module base

4.

Hole cover seal

5.

Power window motor

6.

Door regulator 

7.

Door corner piece weather-strip up-
per

8.

Door corner piece weather-strip low-
er

9.

Door corner piece assembly

10. Door inside seal

: Vehicle front

JMKIA8390ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

GW-26

< REMOVAL AND INSTALLATION >

DOOR GLASS

4.

Operate the power window main switch to raise or lower the
door window until the glass mounting bolts can be seen.

5.

Remove door glass mounting bolts (A).

6.

Remove the door glass.

CAUTION:

When removing or installing, 2 workers are required because of the weight of the glass and for
safety reasons.

a.

Hold securely the door glass.

b.

Rotate slightly the door glass 

c.

Pull up the door glass out to remove.

7.

Remove the corner piece assembly.

a.

Remove door mirror assembly. Refer to 

MIR-19, "DOOR MIRROR ASSEMBLY : Removal and Installa-

tion"

.

b.

Remove corner piece assembly mounting bolts and nut.

c.

Pull up while rotating corner piece assembly to remove out of the door panel.

INSTALLATION

Install in the reverse order of removal.

Inspection and Adjustment

INFOID:0000000008462464

SYSTEM INITIALIZATION

• Description: Refer to 

PWC-26, "Description"

.

• Work procedure: Refer to 

PWC-26, "Work Procedure"

.

CHECK ANTI-PINCH FUNCTION

• Description: Refer to 

PWC-27, "Description"

.

• Work procedure: Refer to 

PWC-27, "Work Procedure"

.

FITTING INSPECTION

JMKIA8392ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

DOOR GLASS

GW-27

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

GW

N

O

P

Preparation for adjustment

1.

Apply protective tape (A) as shown on the figure above on door glass and quarter window glass.

2.

Fully close door window glass and quarter window glass, and mark each edge of weather-strip on the
glass as shown by the marks (B).

3.

Measure the clearances (C), (D), and (E) and check that these clearances are in the range provided in the
figure above. If not, then proceed to the adjustment of quarter window glass by following the steps below.

JMKIA8395ZZ

1.

Door glass assembly

2.

Quarter window glass

C:

4.0 (0.157)

D:

9.8 (0.386)

E:

9.8 (0.386)

Unit: mm (in)

Revision: 2012 October

2013 Murano CrossCabriolet

GW-28

< REMOVAL AND INSTALLATION >

DOOR GLASS

Fitting between door glass and corner piece assembly

1.

Remove the door glass. Refer to 

GW-25, "Removal and Installation"

.

2.

Apply protective tape (B) on door glass at a distance of 25.5 mm (0.1004in), starting from front edge as
shown in the figure above.

JMKIA8393ZZ

1.

Door glass

2.

Mirror base

3.

Quarter window glass

4.

Door weather -strip

F

: 25.5 (1.0004)

G

: 4 (0.157) 

H

: 6.6 (0.260)

I

: 9.8 (0.386) 

J

: 9.1 (0.358)

K

: 8.5 (0.335)

L

: 2 (0.079)

M

: 2 (0.079)

Unit: mm (in)

Revision: 2012 October

2013 Murano CrossCabriolet

DOOR GLASS

GW-29

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

GW

N

O

P

3.

Reinstall door glass while fitting the corner piece assembly to the protective tape as shown in the figure
above.

Fitting between door glass and quarter window glass

1.

Fully close door glass and quarter window glass.

2.

Check that both upper edges of door glass and quarter window glass are at the same level.

3.

Check that the distance between door glass and quarter window glass sash is 8.5 mm (0.335 in).

Inclination Adjustment

• Check that door glass is fitted securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)] and check that the clearance to the

body side weather-strip is parallel. Loosen the regulator mounting bolts, guide rail mounting bolts, and glass
and guide rail mounting bolts to correct the glass position if the clearance between door glass and body side
weather-strip is not parallel.

• Raise door glass fully and adjust door glass top end and body side weather-strip with adjusting bolt (B), (C),

or (D) as shown in the figure above.

• Always start at adjusting with bolt (B). If the desired angle is not achieved, then proceed to adjusting bolt (C)

and (D) respectively.

• Turn the adjusting bolt clockwise to move the door glass upper end outward.
• Turn the adjusting bolt counterclockwise to move the door glass upper end inward.
• Adjustment process with adjusting bolt (C) is the inverse of adjusting bolt (B) and (D).
• When adjusting with adjusting bolt (D), turn the adjusting bolt clockwise to move the door glass upper end

inward, then counterclockwise to move the door glass upper end outward.

JMKIA8598ZZ

1.

Door glass assembly

2.

Quarter window glass sash

3.

Quarter window glass

B

: 8.5 (0.335)

Unit: mm (in)

JMKIA8396ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

GW-30

< REMOVAL AND INSTALLATION >

DOOR REGULATOR

DOOR REGULATOR

Exploded View

INFOID:0000000008462465

Removal and Installation

INFOID:0000000008462466

REMOVAL

1.

Remove the door glass. Refer to 

GW-25, "Removal and Installation"

.

2.

Disconnect the power window motor harness connector.

3.

Disconnect the harness fixing clips from the door module assembly.

1.    Door panel assembly

2.

Door glass

3.

Module base

4.

Hole cover seal

5.

Power window motor

6.

Door regulator 

7.

Door corner piece weather-strip up-
per

8.

Door corner piece weather-strip low-
er

9.

Door corner piece assembly

10. Door inside seal

: Vehicle front

JMKIA8390ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

DOOR REGULATOR

GW-31

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

GW

N

O

P

4.

Remove door module assembly mounting bolts (A) and then
remove the door module assembly from door panel.

INSTALLATION

Install in the reverse order of removal.

Disassembly and Assembly

INFOID:0000000008462467

DISASSEMBLY

1.

Remove the power window motor from the module assembly.

2.

Remove door regulator assembly from module assembly.

ASSEMBLY

Assemble in the reverse order of disassembly.

Inspection After Removal

INFOID:0000000008462468

Check the regulator assembly for the following items. Replace or
grease it if a malfunction is detected.
• Wire wear
• Regulator deformation

Inspection and Adjustment

INFOID:0000000008462469

SYSTEM INITIALIZATION

• Description: Refer to 

PWC-26, "Description"

.

• Work procedure: Refer to 

PWC-26, "Work Procedure"

.

CHECK ANTI-PINCH FUNCTION

• Description: Refer to 

PWC-27, "Description"

.

• Work procedure: Refer to 

PWC-27, "Work Procedure"

.

FITTING INSPECTION

JMKIA8563ZZ

Glass mounting nut

Tightening torque

: 5.1N.m (0.52kg-m, 45 in-lb)

JMKIA8391ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

GW-32

< REMOVAL AND INSTALLATION >

DOOR REGULATOR

Preparation for adjustment

1.

Apply protective tape (A) as shown on the figure above on door glass and quarter window glass.

2.

Fully close door window glass and quarter window glass, and mark each edge of weather-strip on the
glass as shown by the marks (B).

3.

Measure the clearances (C), (D), and (E) and check that these clearances are in the range provided in the
figure above. If not, then proceed to the adjustment of quarter window glass by following the steps below.

JMKIA8395ZZ

1.

Door glass assembly

2.

Quarter window glass

C:

4.0 (0.157)

D:

9.8 (0.386)

E:

9.8 (0.386)

Unit: mm (in)

Revision: 2012 October

2013 Murano CrossCabriolet

DOOR REGULATOR

GW-33

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

GW

N

O

P

Fitting between door glass and corner piece assembly

1.

Remove the door glass. Refer to 

GW-25, "Removal and Installation"

.

2.

Apply protective tape (B) on door glass at a distance of 25.5 mm (0.1004in), starting from front edge as
shown in the figure above.

JMKIA8393ZZ

1.

Door glass

2.

Mirror base

3.

Quarter window glass

4.

Door weather -strip

F

: 25.5 (1.0004)

G

: 4 (0.157) 

H

: 6.6 (0.260)

I

: 9.8 (0.386) 

J

: 9.1 (0.358)

K

: 8.5 (0.335)

L

: 2 (0.079)

M

: 2 (0.079)

Unit: mm (in)

Revision: 2012 October

2013 Murano CrossCabriolet