Murano Cross Cabriolet Z51 (2013 year). Manual - part 29

DEF-24

< DTC/CIRCUIT DIAGNOSIS >

DOOR MIRROR DEFOGGER

DOOR MIRROR DEFOGGER

Component Function Check

INFOID:0000000008462910

1.

CHECK DOOR MIRROR DEFOGGER

With CONSULT

1.

Turn ignition switch ON.

2.

Select “REAR DEFOGGER” of “BCM” using CONSULT.

3.

Select “REAR DEFOGGER” in “ACTIVE TEST” mode.

4.

Touch “ON”.

5.

Check that both side door mirror glass is getting warmer.

Is the inspection result normal?

YES

>> Door mirror defogger is OK.

NO

>> Refer to 

DEF-24, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000008462911

1.

CHECK FUSE

1.

Turn ignition switch OFF.

2.

Check the following.

-

10A fuse (No.13, located in fuse block (J/B))

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace the blown fuse after repairing the affected circuit if a fuse is blown.

2.

CHECK FUSE BLOCK (J/B)

1.

Turn ignition switch ON.

2.

Check voltage between fuse block (J/B) (fuse block side) and ground.

Is the inspection result normal?

YES

>> INSPECTION END.

NO

>> Replace fuse block (J/B).

(+)

(-)

Condition 

Voltage (V)

(Approx.)

Fuse block (J/B)

Connector

Terminal

M3

10C

Ground

Rear window de-
fogger switch

ON

Battery voltage

OFF

0

Revision: 2012 October

2013 Murano CrossCabriolet

DRIVER SIDE DOOR MIRROR DEFOGGER

DEF-25

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

DEF

N

O

P

DRIVER SIDE DOOR MIRROR DEFOGGER

Component Function Check

INFOID:0000000008462912

1.

CHECK DRIVER SIDE DOOR MIRROR DEFOGGER

With CONSULT

1.

Turn ignition switch ON.

2.

Select “REAR DEFOGGER” of “BCM” using CONSULT.

3.

Select “REAR DEFOGGER” in “ACTIVE TEST” mode.

4.

Touch “ON”.

5.

Check that the driver side door mirror glass is getting warmer.

Is the inspection result normal?

YES

>> Driver side door mirror defogger is OK.

NO

>> Refer to 

DEF-25, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000008462913

1.

CHECK POWER SUPPLY CIRCUIT 

1.

Turn ignition switch OFF.

2.

Disconnect door mirror (driver side) connector. 

3.

Turn ignition switch ON.

4.

Check voltage between door mirror (driver side) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 2.

2.

CHECK FUSE BLOCK (J/B) OUTPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect fuse block (J/B) connector. 

3.

Turn ignition switch ON.

4.

Check voltage between fuse block (J/B) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace fuse block (J/B).

3.

CHECK DRIVER SIDE DOOR MIRROR DEFOGGER CIRCUIT

1.

Turn ignition switch OFF.

2.

Check continuity between fuse block (J/B) harness connector and door mirror (driver side) harness con-
nector.

(+)

(-)

Condition

Voltage (V)

(Approx.)

Door mirror (driver side)

 Connector

Terminal 

D3

7

Ground

Rear window de-
fogger switch

ON

Battery voltage

OFF

0

(+)

(-)

Condition

Voltage (V)

(Approx.)

Fuse block (J/B)

 Connector

Terminal 

M3

10C

Ground

Rear window de-
fogger switch

ON

Battery voltage

OFF

0

Revision: 2012 October

2013 Murano CrossCabriolet

DEF-26

< DTC/CIRCUIT DIAGNOSIS >

DRIVER SIDE DOOR MIRROR DEFOGGER

3.

Check continuity between fuse block (J/B) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace harness.

4.

CHECK GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Check continuity between door mirror (driver side) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace harness.

5.

CHECK DRIVER SIDE DOOR MIRROR DEFOGGER

Check driver side door mirror defogger.
Refer to 

DEF-26, "Component Inspection"

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Replace door mirror (driver side). 

6.

CHECK INTERMITTENT INCIDENT

Check intermittent incident.
Refer to 

GI-40, "Intermittent Incident"

.

Is the inspection result normal?

>> INSPECTION END.

Component Inspection

INFOID:0000000008462914

1.

CHECK DRIVER SIDE DOOR MIRROR DEFOGGER 

1.

Turn ignition switch OFF.

2.

Disconnect door mirror (driver side) connector.

3.

Check continuity between door mirror terminals.

Is the inspection result normal?

YES

>> INSPECTION END.

NO

>> Replace door mirror (driver side). 

Fuse block (J/B)

Door mirror (driver side)

Continuity

 Connector

Terminal 

Connector

Terminal

M3

10C

D3

7

Existed

Fuse block (J/B)

Ground

Continuity 

Connector

Terminal

M3

10C

Ground

Not existed 

Door mirror (driver side)

Ground

Continuity 

Connector

Terminal

D3

19

Ground

Existed

Door mirror (driver side)

Continuity 

 Connector

Terminal 

D3

7

19

Existed

Revision: 2012 October

2013 Murano CrossCabriolet

PASSENGER SIDE DOOR MIRROR DEFOGGER

DEF-27

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

DEF

N

O

P

PASSENGER SIDE DOOR MIRROR DEFOGGER

Component Function Check

INFOID:0000000008462915

1.

CHECK PASSENGER SIDE DOOR MIRROR DEFOGGER

With CONSULT

1.

Turn ignition switch ON.

2.

Select “REAR DEFOGGER” of “BCM” using CONSULT.

3.

Select “REAR DEFOGGER” in “ACTIVE TEST” mode.

4.

Touch “ON”.

5.

Check that the passenger side door mirror glass is getting warmer.

Is the inspection result normal?

YES

>> Passenger side door mirror defogger is OK.

NO

>> Refer to 

DEF-27, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000008462916

1.

CHECK POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect door mirror (passenger side) connector.

3.

Turn ignition switch ON.

4.

Check voltage between door mirror (passenger side) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 2.

2.

CHECK FUSE BLOCK (J/B) OUTPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect fuse block (J/B) connector.

3.

Turn ignition switch ON.

4.

Check voltage between fuse block (J/B) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace fuse block (J/B).

3.

CHECK PASSENGER SIDE DOOR MIRROR DEFOGGER

1.

Turn ignition switch OFF.

2.

Check continuity between fuse block (J/B) harness connector and door mirror (passenger side) harness
connector.

(+)

(-)

Condition

Voltage (V)

(Approx.)

Door mirror (Passenger side)

Connector

Terminal 

D43

7

Ground

Rear window de-
fogger switch

ON

Battery voltage

OFF

0

(+)

(-)

Condition 

Voltage (V)

(Approx.)

Fuse block (J/B)

Connector

Terminal 

M3

10C

Ground

Rear window de-
fogger switch

ON

Battery voltage

OFF

0

Revision: 2012 October

2013 Murano CrossCabriolet

DEF-28

< DTC/CIRCUIT DIAGNOSIS >

PASSENGER SIDE DOOR MIRROR DEFOGGER

3.

Check continuity between fuse block (J/B) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace harness. 

4.

CHECK GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Check continuity between door mirror (passenger side) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace harness.

5.

CHECK PASSENGER SIDE DOOR MIRROR DEFOGGER

Check passenger side door mirror defogger.
Refer to 

DEF-28, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Replace door mirror (passenger side)..

6.

CHECK INTERMITTENT INCIDENT

Check intermittent incident.
Refer to 

GI-40, "Intermittent Incident"

.

>> INSPECTION END.

Component Inspection

INFOID:0000000008462917

1.

CHECK PASSENGER DOOR MIRROR DEFOGGER 

1.

Turn ignition switch OFF.

2.

Disconnect door mirror (passenger side) connector.

3.

Check continuity between door mirror terminals.

Is the inspection result normal?

YES

>> INSPECTION END.

NO

>> Replace door mirror (passenger side).

Fuse block (J/B)

Door mirror (passenger side)

Continuity

Connector

Terminal Connector

Terminal

M3

10C

D43

7

Existed

Fuse block (J/B)

Ground

Continuity

Connector

Terminal 

M3

10C

Ground

Not existed

Door mirror (passenger side)

Ground

Continuity 

Connector

Terminal

D43

19

Ground

Existed

Door mirror (passenger side) 

Continuity 

Connector

Terminal 

D43

7

19

Existed

Revision: 2012 October

2013 Murano CrossCabriolet

REAR WINDOW DEFOGGER AND DOOR MIRROR DEFOGGERS DO NOT OP-

ERATE

DEF-29

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

DEF

N

O

P

SYMPTOM DIAGNOSIS

REAR WINDOW DEFOGGER AND DOOR MIRROR DEFOGGERS DO NOT
OPERATE

Diagnosis Procedure

INFOID:0000000008462918

1.

CHECK REAR WINDOW DEFOGGER SWITCH

Check rear window defogger switch.
Refer to 

DEF-17, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK REAR WINDOW DEFOGGER RELAY

Check rear window defogger relay. 
Refer to 

DEF-18, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CONFIRM THE OPERATION

Confirm the operation again.
Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

NO

>> GO TO 1.

Revision: 2012 October

2013 Murano CrossCabriolet

DEF-30

< SYMPTOM DIAGNOSIS >

REAR WINDOW DEFOGGER DOES NOT OPERATE BUT BOTH DOOR MIRROR 

DEFOGGERS OPERATE

REAR WINDOW DEFOGGER DOES NOT OPERATE BUT BOTH DOOR
MIRROR DEFOGGERS OPERATE

Diagnosis Procedure

INFOID:0000000008462919

1.

CHECK SOFT TOP CONTROL UNIT CIRCUIT

Check soft top control unit circuit. 
Refer to 

DEF-20, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK REAR WINDOW DEFOGGER

Check rear window defogger.
Refer to 

DEF-22, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CONFIRM THE OPERATION

Confirm the operation again

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

NO

>> GO TO 1.

Revision: 2012 October

2013 Murano CrossCabriolet

DOOR MIRROR DEFOGGER DOES NOT OPERATE BUT REAR WINDOW DE-

FOGGER OPERATE

DEF-31

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

DEF

N

O

P

DOOR MIRROR DEFOGGER DOES NOT OPERATE BUT REAR WINDOW
DEFOGGER OPERATE

BOTH SIDES

BOTH SIDES : Diagnosis Procedure

INFOID:0000000008462920

1.

CHECK DOOR MIRROR DEFOGGER

Check door mirror defogger.
Refer to 

DEF-24, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CONFIRM THE OPERATION

Confirm the operation again.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

NO

>> GO TO 1.

DRIVER SIDE

DRIVER SIDE : Diagnosis Procedure

INFOID:0000000008462921

1.

CHECK DRIVER SIDE DOOR MIRROR DEFOGGER 

Check driver side door mirror defogger.
Refer to 

DEF-25, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CONFIRM THE OPERATION

Confirm the operation again.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

NO

>> GO TO 1.

PASSENGER SIDE

PASSENGER SIDE : Diagnosis Procedure

INFOID:0000000008462922

1.

CHECK PASSENGER SIDE DOOR MIRROR DEFOGGER.

Check passenger side door mirror defogger.
Refer to 

DEF-27, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CONFIRM THE OPERATION

Confirm the operation again.
Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

NO

>> GO TO 1.

Revision: 2012 October

2013 Murano CrossCabriolet

DEF-32

< SYMPTOM DIAGNOSIS >

ON IS NOT DISPLAYED WHEN PRESSING REAR WINDOW DEFOGGER 

SWITCH BUT IT OPERATES

ON IS NOT DISPLAYED WHEN PRESSING REAR WINDOW DEFOGGER
SWITCH BUT IT OPERATES

Diagnosis Procedure

INFOID:0000000008462923

1.

CHECK AV CONTROL FUNCTION

Check that the AV control unit is operating normally.
Refer to 

AV-55, "Work Flow"

 (BOSE audio without navigation).

Refer to 

AV-170, "Work Flow"

 (BOSE sudio with navigation).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CONFIRM THE OPERATION

Confirm the operation again.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

NO

>> GO TO 1.

Revision: 2012 October

2013 Murano CrossCabriolet

REAR WINDOW DEFOGGER INDICATOR DOES NOT ILLUMINATE

DEF-33

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

DEF

N

O

P

REAR WINDOW DEFOGGER INDICATOR DOES NOT ILLUMINATE

Diagnosis Procedure

INFOID:0000000008462924

1.

CHECK REAR WINDOW DEFOGGER OPERATION

Check rear window defogger operation.
Is the inspection result normal?

YES-1 >> Check AV control system (BOSE audio without navigation). Refer to 

AV-55, "Work Flow"

.

YES-2 >> Check AV control system (BOSE audio with navigation). Refer to 

AV-170, "Work Flow"

.

NO

>> Check rear window defogger system. Refer to 

DEF-16, "Work Flow"

.

Revision: 2012 October

2013 Murano CrossCabriolet

DEF-34

< REMOVAL AND INSTALLATION >

FILAMENT

REMOVAL AND INSTALLATION

FILAMENT

Inspection and Repair

INFOID:0000000008462925

INSPECTION

1.

When measuring voltage, wrap tin foil around the top of the neg-
ative probe. Then press the foil against the wire with your finger.

2.

Attach probe circuit tester (in Volt range) to middle portion of
each filament.

3.

If a filament is burned out, circuit tester registers 0 or battery
voltage.

4.

To locate burned out point, move probe to left and right along fil-
ament. Test needle will swing abruptly when probe passes the
point.

REPAIR

REPAIR EQUIPMENT

• Conductive silver composition (Dupont No. 4817 or equivalent)

SEL122R

SEL263

SEL265

Revision: 2012 October

2013 Murano CrossCabriolet

FILAMENT

DEF-35

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

DEF

N

O

P

• Ruler 30 cm (11.8 in) long
• Drawing pen
• Heat gun
• Alcohol
• Cloth

REPAIRING PROCEDURE

1.

Wipe broken heat wire and its surrounding area clean with a
cloth dampened in alcohol.

2.

Apply a small amount of conductive silver composition to tip of
drawing pen.
Shake silver composition container before use.

3.

Place ruler on glass along broken line. Deposit conductive silver
composition on break with drawing pen. Slightly overlap existing
heat wire on both sides [preferably 5 mm (0.20 in)] of the break.

4.

After repair has been completed, check repaired wire for conti-
nuity. This check should be conducted 10 minutes after silver
composition is deposited.
Do not touch repaired area while test is being conducted.

5.

Apply a constant stream of hot air directly to the repaired area
for approximately 20 minutes with a heat gun. A minimum dis-
tance of 3 cm (1.2 in) should be kept between repaired area and
hot air outlet.
If a heat gun is not available, let the repaired area dry for 24
hours.

PIIA0215E

SEL012D

SEL013D

Revision: 2012 October

2013 Murano CrossCabriolet

DEF-36

< REMOVAL AND INSTALLATION >

CONDENSER

CONDENSER

Removal and Installation

INFOID:0000000008462926

REMOVAL

1.

Remove the trunk front finisher.
Refer to 

INT-36, "TRUNK FRONT FINISHER : Removal and Installation"

2.

Remove bolt (A), and then remove condenser (1) from the vehi-
cle body.

INSTALLATION

Install in the reverse order of removal.

JMLIA2221ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

EX-1

ENGINE

C

D

E

F

G

H

I

J

K

L

M

SECTION 

EX

A

EX

N

O

P

CONTENTS

EXHAUST SYSTEM

PRECAUTION ...............................................

2

PRECAUTIONS ...................................................

2

Removal and Installation ...........................................

2

PREPARATION ............................................

3

PREPARATION ...................................................

3

Commercial Service Tool  ..........................................

3

PERIODIC MAINTENANCE ..........................

4

EXHAUST SYSTEM ...........................................

4

Inspection .................................................................

4

REMOVAL AND INSTALLATION  ................

5

EXHAUST SYSTEM ...........................................

5

Exploded View ..........................................................

5

Removal and Installation  ..........................................

5

Inspection .................................................................

6

Revision: 2012 October

2013 Murano CrossCabriolet

EX-2

< PRECAUTION >

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Removal and Installation

INFOID:0000000008462089

CAUTION:

• Be sure to use genuine exhaust system parts or equivalents which are specially designed for heat

resistance, corrosion resistance, and shape.

• Perform the operation with the exhaust system fully cooled down because the system will be hot

just after engine stops. 

• Be careful not to cut your hand on the heat insulator edge.

Revision: 2012 October

2013 Murano CrossCabriolet

PREPARATION

EX-3

< PREPARATION >

C

D

E

F

G

H

I

J

K

L

M

A

EX

N

P

O

PREPARATION

PREPARATION

Commercial Service Tool

INFOID:0000000008462090

Tool name

Description

Power tool

Loosening nuts and bolts

PBIC0190E

Revision: 2012 October

2013 Murano CrossCabriolet