Nissan Murano Z51 (2013 year). Manual - part 81

ST-4

< PRECAUTION >

[WITH HEATED STEERING WHEEL]

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT 
PRE-TENSIONER"

INFOID:0000000008459262

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.

WARNING:

Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.

• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-

vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the

ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.

• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

Service Notice or Precautions for Steering System

INFOID:0000000008459263

• In case of removing steering gear assembly, make the final tightening with grounded and unloaded vehicle

condition, and then check wheel alignment.

• Observe the following precautions when disassembling.
- Before disassembly, thoroughly clean the outside of the unit.
- Disassembly should be done in a clean work area. It is important to prevent the internal parts from becoming

contaminated by dirt or other foreign matter.

- For easier and proper assembly, place disassembled parts in order on a parts rack.
- Use nylon cloth or paper towels to clean the parts; common shop rags can leave lint that might interfere with

their operation.

- Never reuse non-reusable parts.
- Before assembling, apply the specified grease to the directed parts.

Revision: 2012 September

2013 MURANO

PREPARATION

ST-5

< PREPARATION >

[WITH HEATED STEERING WHEEL]

C

D

E

F

H

I

J

K

L

M

A

B

ST

N

O

P

PREPARATION

PREPARATION

Special Service Tools

INFOID:0000000008459264

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Tool number
(Kent-Moore No.)
Tool name

Description

ST27180001
(J-25726-A)
Steering wheel puller

Removing steering wheel

ST3127S000
(J-25765-A)
Preload gauge

• Measuring steering column rotating torque
• Measuring pinion rotating torque
• Measuring ball joint rotating torque

KV48104400
(

—

)

Teflon ring correcting tool
a: 50 mm (1.97 in) dia.
b: 36 mm (1.42 in) dia.
c: 100 mm (3.94 in)

Installing rack Teflon ring

KV48103400
(

—

)

Preload adapter

Measuring pinion rotating torque

ST35300000
(

—

)

Drift
a: 45.1 mm (1.776 in) dia.
b: 59.0 mm (2.323 in) dia.

Installing oil pump oil seal

ZZA0819D

ZZA0806D

S-NT550

ZZA0824D

ZZA0881D

Revision: 2012 September

2013 MURANO

ST-6

< PREPARATION >

[WITH HEATED STEERING WHEEL]

PREPARATION

Commercial Service Tools

INFOID:0000000008459265

KV48103500
(J-26357)
Oil pressure gauge

Measuring oil pump relief pressure

KV48102500
(J-33914)
Oil pressure gauge adapter

Measuring oil pump relief pressure

Tool number
(Kent-Moore No.)
Tool name

Description

S-NT547

S-NT542

Tool name

Description

Power tool

Loosening bolts and nuts

Ball joint remover

Removing steering outer socket

Open head

Tightening end cover assembly

PBIC0190E

S-NT146

ZZA0822D

Revision: 2012 September

2013 MURANO

PREPARATION

ST-7

< PREPARATION >

[WITH HEATED STEERING WHEEL]

C

D

E

F

H

I

J

K

L

M

A

B

ST

N

O

P

Drift
a: 15 mm (0.59 in) dia.
b: 10 mm (0.39 in) dia.

Installing rotor snap ring

Drift
a: 36 mm (1.42 in) dia.
b: 20 mm (0.79 in) dia.

Installing oil pump oil seal

Tool name

Description

S-NT474

S-NT474

Revision: 2012 September

2013 MURANO

ST-8

< SYSTEM DESCRIPTION >

[WITH HEATED STEERING WHEEL]

COMPONENT PARTS

SYSTEM DESCRIPTION

COMPONENT PARTS

Component Parts Location (Heated Steering Wheel)

INFOID:0000000008459266

Component Description (Heated Steering Wheel)

INFOID:0000000008459267

Heated Steering Wheel

INFOID:0000000008459268

The heated steering wheel is activated by the power supply from the heated steering wheel relay.
Furthermore, the heated steering wheel incorporates a heating element and a thermostat to control heated
steering wheel temperatures.
• Heating element: Heat is generated by the passage of an electric current.
• Thermostat: ON/OFF operation of power supply at a certain temperature. 

Heated Steering Wheel Switch

INFOID:0000000008459269

• Controls the heated steering wheel relay and operates the heated steering wheel system. 

The heated steering wheel switch incorporates a timer and turns OFF the heated steering wheel relay when
operating time reaches a certain time. 

- Timer: ON/OFF operation of the heated steering wheel relay at a certain time.
• Turns the indicator lamp ON when the system is activated.

Heated Steering Wheel Relay

INFOID:0000000008459270

Operates the heated steering system with the control signal from the heated steering wheel switch.

1.

Heated steering wheel relay
Refer to 

PG-38, "Main Harness"

.

2.

Heated steering wheel switch

3.

Heated steering wheel

JPGIA0195ZZ

Part name

Reference/Function

Heated steering wheel

Heating element

Refer to 

ST-8, "Heated Steering Wheel"

.

Thermostat

Heated steering wheel relay

Refer to 

ST-8, "Heated Steering Wheel Relay"

.

Heated steering wheel switch

Timer

Refer to 

ST-8, "Heated Steering Wheel Switch"

.

Revision: 2012 September

2013 MURANO

SYSTEM

ST-9

< SYSTEM DESCRIPTION >

[WITH HEATED STEERING WHEEL]

C

D

E

F

H

I

J

K

L

M

A

B

ST

N

O

P

SYSTEM

System Description (Heated Steering Wheel)

INFOID:0000000008459271

The heated steering wheel switch controls the heated steering wheel relay. When the heated steering wheel
switch is turned on, the heated steering wheel relay is energized and the heated steering wheel system will
operate. The heated steering wheel system will turn off when the heated steering wheel temperature reaches
approximately 30

°

C (86

°

F). Heated steering wheel system operation can also be canceled by pressing the

heated steering wheel switch again. In addition, the heated steering wheel switch incorporates a timer and
turns OFF the heated steering wheel relay to exit the heated steering wheel system when the operating time
reaches a certain time.
NOTE:
If the surface temperature of the steering wheel is below 20

°

C (68

°

F), the system will heat the steering wheel

and cycle off and on to maintain a temperature above 20

°

C (68

°

F). The indicator lamp will remain on as long

as the system is on. Push the switch again to turn the heated steering wheel system off manually. The indica-
tor lamp will go off.

SYSTEM DIAGRAM

JSGIA0826GB

Revision: 2012 September

2013 MURANO

ST-10

< WIRING DIAGRAM >

[WITH HEATED STEERING WHEEL]

HEATED STEERING WHEEL

WIRING DIAGRAM

HEATED STEERING WHEEL

Wiring Diagram

INFOID:0000000008459272

For connector terminal arrangements, harness layouts, and alphabets in a

(option abbreviation; if not

described in wiring diagram), refer to 

GI-12, "Connector Information"

.

JCGWM0468GB

Revision: 2012 September

2013 MURANO

DIAGNOSIS AND REPAIR WORK FLOW

ST-11

< BASIC INSPECTION >

[WITH HEATED STEERING WHEEL]

C

D

E

F

H

I

J

K

L

M

A

B

ST

N

O

P

BASIC INSPECTION

DIAGNOSIS AND REPAIR WORK FLOW

WorkFlow (Heated Steering Wheel)

INFOID:0000000008459273

DETAILED FLOW

1.

OBTAIN INFORMATION ABOUT SYMPTOM

Interview the customer to obtain the malfunction information (conditions and environment when the malfunc-
tion occurred) as much as possible when the customer brings the vehicle in.

>> GO TO 2.

2.

REPRODUCE THE MALFUNCTION INFORMATION

Check the malfunction on the vehicle that the customer describes.
Inspect the relation of the symptoms and the condition when the symptoms occur.

>> GO TO 3.

3.

IDENTIFY THE MALFUNCTIONING SYSTEM WITH “SYMPTOM DIAGNOSIS”

Use “Symptom diagnosis” from the symptom inspection result in step 2 and then identify where to start per-
forming the diagnosis based on possible causes and symptoms.

>> GO TO 4.

4.

IDENTIFY THE MALFUNCTIONING PARTS WITH “COMPONENT DIAGNOSIS”

Perform the diagnosis with “Component diagnosis” of the applicable system.

>> GO TO 5.

5.

REPAIR OR REPLACE THE MALFUNCTIONING PARTS

Repair or replace the specified malfunctioning parts.

>> GO TO 6.

6.

FINAL CHECK

Check that malfunctions are not reproduced when obtaining the malfunction information from the customer,
referring to the symptom inspection result in step 2.

Are the malfunctions corrected?

YES

>> INSPECTION END

NO

>> GO TO 2.

Revision: 2012 September

2013 MURANO

ST-12

< BASIC INSPECTION >

[WITH HEATED STEERING WHEEL]

STEERING WHEEL

STEERING WHEEL

Inspection

INFOID:0000000008459274

NEUTRAL POSITION STEERING WHEEL

1.

Check that steering gear assembly, steering column assembly and steering wheel are installed in the cor-
rect position.

2.

Perform neutral position inspection after wheel alignment. Refer to 

FSU-7, "Inspection"

.

3.

Set the vehicle to the straight-ahead position and confirm steering wheel is in the neutral position.

4.

Loosen outer socket lock nut and turn inner socket to left and right equally to make fine adjustments if
steering wheel is not in the neutral position.

STEERING WHEEL TURNING FORCE

1.

Park the vehicle on a level and dry surface, set parking brake.

2.

Tires need to be inflated normal pressure. Refer to 

WT-49, "Tire Air Pressure"

.

3.

Start the engine.

4.

Bring power steering fluid up to adequate operating temperature.

5.

Check steering wheel turning force when steering wheel has
been turned 540

°

 from neutral position.

NOTE:
Multiply the distance (L) from the hook of spring balance to the
center of steering wheel by the measurement value with a spring
balance.

6.

If steering wheel turning force is out of the specification, check
rack sliding force and relief hydraulic pressure of oil pump. Regarding relief hydraulic pressure of oil
pump, refer to 

ST-60, "Inspection"

.

RACK SLIDING FORCE

1.

Disconnect lower joint and steering knuckle from steering gear assembly. Refer to 

ST-41, "Exploded

View"

.

2.

Start and run the engine at idle to make sure steering fluid has reached normal operating temperature.

3.

While pulling outer socket slowly in 

±

11.5 mm (

±

0.453 in) range

from neutral position, make sure rack sliding force is within
specification.

4.

If rack sliding force is not within specification, overhaul steering
gear assembly.

FRONT WHEEL TURNING ANGLE

1.

Check front wheel turning angle after toe-in inspection. Refer to 

FSU-7, "Inspection"

.

Fluid temperature

: 50 – 80

°

C (122 – 176

°

F)

Standard

Steering wheel turning 
force

: Refer to 

ST-65, "Steering 

Wheel Turning Force"

.

JSGIA0027ZZ

Fluid temperature

: 50 – 80

°

C (122 – 176

°

F)

Standard

Rack sliding force

: Refer to 

ST-66, "Rack 

Sliding Force"

.

SST090B

Revision: 2012 September

2013 MURANO

STEERING WHEEL

ST-13

< BASIC INSPECTION >

[WITH HEATED STEERING WHEEL]

C

D

E

F

H

I

J

K

L

M

A

B

ST

N

O

P

2.

Place front wheels on turning radius gauges and rear wheels on
stands, so that vehicle can be level.

3.

Check the maximum inner and outer wheel turning angles for LH
and RH road wheels.

4.

With the engine at idle, turn steering wheel from full left stop to
full right stop and measure the turning angles.

5.

Check the following items when turning angle is out of the stan-
dard.

a.

Check the neutral position of the rack stroke (L).

b.

Disassemble steering gear assembly to check the cause that
rack stroke is outside of the standard.
• Steering angles are not adjustable. Check steering gear

assembly, steering column assembly and front suspension
components for wear or damage if any of the turning angles are different from the specified value.
Replace any of them, if any non-standard condition exists.

FAA0016D

Standard

Inner wheel (Angle: A)

: Refer to 

ST-65, "Steering 

Angle"

.

Outer wheel (Angle: B)

: Refer to 

ST-65, "Steering 

Angle"

.

SGIA0055E

Standard

Rack stroke neutral position (L)

: Refer to 

ST-66, 

"Rack Stroke"

.

SGIA0629J

Revision: 2012 September

2013 MURANO

ST-14

< DTC/CIRCUIT DIAGNOSIS >

[WITH HEATED STEERING WHEEL]

HEATED STEERING WHEEL SYSTEM

DTC/CIRCUIT DIAGNOSIS

HEATED STEERING WHEEL SYSTEM

Component Function Check

INFOID:0000000008459275

1.

CHECK HEATED STEERING WHEEL SYSTEM

Check operate heated steering wheel system. Refer to 

ST-9, "System Description (Heated Steering Wheel)"

.

Is the inspection result normal?

YES

>> Go to 

ST-14, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000008459276

1.

CHECK POWER SOURCE AND GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Remove the heated steering wheel. Refer to 

ST-34, "Removal and Installation"

.

3.

Turn ignition switch ON.

CAUTION:

Never start the engine.

4.

Turn heated steering wheel switch ON.

5.

Check voltage between heated steering wheel harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> GO TO 3.

2.

CHECK HEATED STEERING WHEEL

Check heated steering wheel. Refer to 

ST-16, "Component Inspection (Heated Steering Wheel)"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace heated steering wheel. Refer to 

ST-34, "Removal and Installation"

.

3.

CHECK GROUND CIRCUIT

Check continuity between heated steering wheel harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace damaged parts.

4.

CHECK HARNESS BETWEEN HEATED STEERING WHEEL RELAY AND HEATED STEERING WHEEL

1.

Turn ignition switch OFF.

2.

Disconnect heated steering wheel relay connector. Refer to 

ST-8, "Component Parts Location (Heated

Steering Wheel)"

.

3.

Disconnect heated steering wheel switch connector. Refer to 

ST-64, "Removal and Installation"

.

4.

Check continuity between heated steering wheel relay harness connector terminal and heated steering
wheel harness connector terminal.

Heated steering wheel

Condition

Voltage (Approx.)

Connector

Terminal

M309

1 

−

 2

Within 30 minutes after 
turning ON the heated 
steering switch.

Battery voltage

Other conditions.

0 V

Heated steering wheel

Ground

Continuity

Connector

Terminal

M309

2

Existed

Revision: 2012 September

2013 MURANO

HEATED STEERING WHEEL SYSTEM

ST-15

< DTC/CIRCUIT DIAGNOSIS >

[WITH HEATED STEERING WHEEL]

C

D

E

F

H

I

J

K

L

M

A

B

ST

N

O

P

5.

Check continuity between heated steering wheel relay harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace damaged parts.

5.

CHECK HEATED STEERING WHEEL RELAY

Check heated steering wheel relay. Refer to 

ST-17, "Component Inspection (Heated Steering Wheel Relay)"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Replace heated steering wheel relay. Refer to 

ST-8, "Component Parts Location (Heated Steering

Wheel)"

.

6.

CHECK POWER SUPPLY (BATTERY)

Check the following.
• Battery
• Harness for short or open between battery and 15 A fuse (No.26).
• 15 A fuse (No.26).
• Harness for short or open between 15 A fuse (No.26) and heated steering wheel relay.
Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace damaged parts.

7.

CHECK GROUND CIRCUIT

Check continuity between heated steering wheel switch harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Repair or replace damaged parts.

8.

CHECK HARNESS BETWEEN HEATED STEERING WHEEL RELAY AND HEATED STEERING WHEEL

SWITCH

1.

Check continuity between heated steering wheel relay harness connector terminal and heated steering
wheel switch harness connector terminal.

2.

Check continuity between heated steering wheel relay harness connector terminal and ground.

Heated steering wheel relay

Heated steering wheel

Continuity

Connector

Terminal

Connector

Terminal

M27

5

M309

1

Existed

7

Heated steering wheel relay

Ground

Continuity

Connector

Terminal

M27

5

Not existed

7

Heated steering wheel switch

Ground

Continuity

Connector

Terminal

M28

6

Existed

Heated steering wheel relay

Heated steering wheel switch

Continuity

Connector

Terminal

Connector

Terminal

M27

2

M28

2

Existed

Revision: 2012 September

2013 MURANO

ST-16

< DTC/CIRCUIT DIAGNOSIS >

[WITH HEATED STEERING WHEEL]

HEATED STEERING WHEEL SYSTEM

Is the inspection result normal?

YES

>> GO TO 9.

NO

>> Repair or replace damaged parts.

9.

CHECK HARNESS BETWEEN FUSE BLOCK (J/B) AND HEATED STEERING WHEEL SWITCH

1.

Check continuity between fuse block (J/B) connector terminal and heated steering wheel switch harness
connector terminal.

2.

Check continuity between fuse block (J/B) harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 10.

NO

>> Repair or replace damaged parts.

10.

CHECK POWER SUPPLY (IGNITION)

Check the following.
• Ignition switch
• Harness for short or open between ignition switch and fuse block (J/B). Refer to 

PG-21, "Wiring Diagram -

IGNITION POWER SUPPLY -"

.

• 10A fuse [No.3, located in the fuse block (J/B)]. Refer to 

PG-112, "Fuse, Connector and Terminal Arrange-

ment"

.

• Fuse block (J/B)
Is the inspection result normal?

YES

>> Replace heated steering wheel switch. Refer to 

ST-64, "Removal and Installation"

.

NO

>> Repair or replace damaged parts.

Component Inspection (Heated Steering Wheel)

INFOID:0000000008459277

1.

CHECK HEATED STEERING WHEEL CONTINUITY

Check continuity between heated steering wheel connector terminals.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace heated steering wheel. Refer to 

ST-34, "Removal and Installation"

.

2.

CHECK HEATED STEERING WHEEL RESISTANCE

Check resistance between heated steering wheel connector terminals.

Heated steering wheel relay

Ground

Continuity

Connector

Terminal

M27

2

Not existed

 Fuse block (J/B)

Heated steering wheel switch

Continuity

Connector

Terminal

Connector

Terminal

M1

2A

M28

1

Existed

 Fuse block (J/B)

Ground

Continuity

Connector

Terminal

M1

2A

Not existed

Heated steering wheel

Condition

Continuity

Terminal

1 

−

 2

Leather surface temperature of 
20

°

C (68

°

F) or less

Existed

Leather surface temperature of 
30

°

C (86

°

) or more

Not existed

Revision: 2012 September

2013 MURANO

HEATED STEERING WHEEL SYSTEM

ST-17

< DTC/CIRCUIT DIAGNOSIS >

[WITH HEATED STEERING WHEEL]

C

D

E

F

H

I

J

K

L

M

A

B

ST

N

O

P

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace heated steering wheel. Refer to 

ST-34, "Removal and Installation"

.

Component Inspection (Heated Steering Wheel Relay)

INFOID:0000000008459278

1.

CHECK HEATED STEERING WHEEL RELAY CONTINUITY

Check continuity between heated steering wheel relay terminals.

CAUTION:

Connect the fuse between the terminals when applying the voltage.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace heated steering wheel relay. Refer to 

ST-8, "Component Parts Location (Heated Steering

Wheel)"

.

Heated steering wheel

Condition

Resistance (Approx.)

Terminal

1 

−

 2

Leather surface temperature of 
20

°

C (68

°

F)

1.83 

Ω

Heated steering wheel relay

Condition

Continuity

Terminal

3 

−

 5

6 

−

 7

Apply 12 V direct current be-
tween terminals 1 and 2. 

Existed

Other conditions.

Not existed

Revision: 2012 September

2013 MURANO

ST-18

< DTC/CIRCUIT DIAGNOSIS >

[WITH HEATED STEERING WHEEL]

HEATED STEERING WHEEL SWITCH INDICATOR LAMP

HEATED STEERING WHEEL SWITCH INDICATOR LAMP

Component Function Check

INFOID:0000000008459279

1.

CHECK HEATED STEERING WHEEL INDICATOR LAMP

1.

Turn ignition switch ON.

2.

Turn heated steering wheel switch ON.

Does heated steering wheel indicator lamp turn on the lamp?

YES

>> GO TO 2.

NO

>> Go to 

ST-18, "Diagnosis Procedure"

.

2.

CHECK HEATED STEERING WHEEL INDICATOR LAMP

Turn heated steering wheel switch OFF.

Does heated steering wheel indicator lamp turn off the lamp?

YES

>> INSPECTION END

NO

>> Go to 

ST-18, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000008459280

1.

CHECK POWER SOURCE AND GROUND CIRCUIT

1.

Turn ignition switch ON.

CAUTION:

Never start the engine.

2.

Turn heated steering wheel switch ON.

3.

Check voltage between heated steering wheel switch harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> GO TO 2.

2.

CHECK POWER SUPPLY (BATTERY)

Check the following.
• Battery
• Harness for short or open between battery and 15 A fuse (No.26).
• 15 A fuse (No.26).
• Harness for short or open between 15 A fuse (No.26) and heated steering wheel relay.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace damaged parts.

3.

CHECK GROUND CIRCUIT

Check continuity between heated steering wheel switch harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace damaged parts.

Heated steering wheel

Condition

Voltage (Approx.)

Connector

Terminal

M28

5 

−

 6

Within 30 minutes after 
turning ON the heated 
steering switch.

Battery voltage

Other conditions.

0 V

Heated steering wheel switch

Ground

Continuity

Connector

Terminal

M28

6

Existed

Revision: 2012 September

2013 MURANO

HEATED STEERING WHEEL SWITCH INDICATOR LAMP

ST-19

< DTC/CIRCUIT DIAGNOSIS >

[WITH HEATED STEERING WHEEL]

C

D

E

F

H

I

J

K

L

M

A

B

ST

N

O

P

4.

CHECK HARNESS BETWEEN HEATED STEERING WHEEL RELAY AND HEATED STEERING WHEEL

SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect heated steering wheel relay connector. Refer to 

ST-8, "Component Parts Location (Heated

Steering Wheel)"

.

3.

Disconnect heated steering wheel switch connector. Refer to 

ST-64, "Removal and Installation"

.

4.

Check continuity between heated steering wheel relay harness connector terminal and heated steering
wheel switch harness connector terminal.

5.

Check continuity between heated steering wheel relay harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace damaged parts.

5.

CHECK HEATED STEERING WHEEL RELAY

Check heated steering wheel relay. Refer to 

ST-20, "Component Inspection (Heated Steering Wheel Relay)"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Replace heated steering wheel relay. Refer to 

ST-8, "Component Parts Location (Heated Steering

Wheel)"

.

6.

CHECK HARNESS BETWEEN HEATED STEERING WHEEL RELAY AND HEATED STEERING WHEEL

SWITCH

1.

Check continuity between heated steering wheel relay harness connector terminal and heated steering
wheel switch harness connector terminal.

2.

Check continuity between heated steering wheel relay harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace damaged parts.

7.

CHECK HARNESS BETWEEN FUSE BLOCK (J/B) AND HEATED STEERING WHEEL SWITCH

1.

Check continuity between fuse block (J/B) connector terminal and heated steering wheel switch harness
connector terminal.

Heated steering wheel relay

Heated steering wheel switch

Continuity

Connector

Terminal

Connector

Terminal

M27

5

M28

5

Existed

7

Heated steering wheel relay

Ground

Continuity

Connector

Terminal

M27

5

Not existed

7

Heated steering wheel relay

Heated steering wheel switch

Continuity

Connector

Terminal

Connector

Terminal

M27

2

M28

2

Existed

Heated steering wheel relay

Ground

Continuity

Connector

Terminal

M27

2

Not existed

Revision: 2012 September

2013 MURANO