Nissan Murano Z51 (2013 year). Manual

MA-6

< PERIODIC MAINTENANCE >

GENERAL MAINTENANCE

UNDER THE HOOD AND VEHICLE

The maintenance items listed here should be checked periodically (e.g. each time you check the engine oil or refuel).

FOR MEXICO

Seats

Check seat position controls such as seat adjusters, seatback recliner, etc. to make
sure they operate smoothly and that all latches lock securely in every position. Check
that the head restrains move up and down smoothly and that the locks (if equipped)
hold securely in all latched positions. Check that the latches lock securely for folding-
down rear seatbacks.

—

Seat belts

Check that all parts of the seat belt system (e.g. buckles, anchors, adjusters and re-
tractors) operate properly and smoothly, and are installed securely. Check the belt
webbing for cuts, fraying, wear or damage.

MA-40

Accelerator pedal

Check the pedal for smooth operation and make sure the pedal does not catch or re-
quire uneven effort. Keep the floor mats away from the pedal.

—

Brakes

Check that the brake does not pull the vehicle to one side when applied.

—

Brake pedal and
booster

Check the pedal for smooth operation and make sure it has the proper distance under
it when depressed fully. Check the brake booster function. Be sure to keep the floor
mats away from the pedal.

BR-8

BR-14

Parking brake

Check that the lever or the pedal has the proper travel and make sure that the vehicle
is held securely on a fairly steep hill when only the parking brake is applied.

PB-3

CVT P (Park) position
mechanism

On a fairly steep hill check that the vehicle is held securely with the selector lever in the
P (Park) position without applying any brakes.

—

Item

Reference page

Item

Reference page

Windshield washer flu-
id

Check that there is adequate fluid in the tank.

—

Engine coolant level

Check the coolant level when the engine is cold.

MA-20

Radiator and hoses

Check the front of the radiator and clean off any dirt, insects, leaves, etc., that may
have accumulated. Make sure the hoses have no cracks, deformation, deterioration or
loose connections.

—

Brake fluid level

Make sure that the brake fluid level is between the “MAX” and “MIN” lines on the res-
ervoir.

MA-36

Battery

Check the fluid level in each cell. It should be between the “MAX” and “MIN” lines. Ve-
hicles operated in high temperatures or under severe conditions require frequent
checks of the battery fluid level.

PG-3

Engine drive belts

Make sure that no belt is frayed, worn, cracked or oily.

MA-20

Engine oil level

Check the level on the oil level gauge after parking the vehicle on a level spot and turn-
ing off the engine.

LU-8

Power steering fluid
level and lines

Check the level on the dipstick with the engine off. Check the lines for improper attach-
ment, leaks, cracks, etc.

MA-38

Exhaust system

Make sure there are no loose supports, cracks or holes. If the sound of the exhaust
seems unusual or there is a smell of exhaust fumes, immediately locate the trouble and
correct it.

MA-30

Underbody

The underbody is frequently exposed to corrosive substances such as those used on
icy roads or to control dust. It is very important to remove these substances, otherwise
rust will form on the floor pan, frame, fuel lines and around the exhaust system. At the
end of winter, the underbody should be thoroughly flushed with plain water, being care-
ful to clean those areas where mud and dirt can easily accumulate.

—

Fluid leaks

Check under the vehicle for fuel, oil, water or other fluid leaks after the vehicle has been
parked for a while. Water dripping from the air conditioner after use is normal. If you
should notice any leaks or gasoline fumes are evident, check for the cause and correct
it immediately.

—

Revision: 2012 September

2013 MURANO

GENERAL MAINTENANCE

MA-7

< PERIODIC MAINTENANCE >

FOR MEXICO : General Maintenance

INFOID:0000000008814476

General maintenance includes those items which should be checked during the normal day-to-day operation
of the vehicle. They are essential if the vehicle is to continue operating properly. The owners can perform the
checks and inspections themselves or they can have their NISSAN dealers do them.

OUTSIDE THE VEHICLE

The maintenance items listed here should be performed from time to time, unless otherwise specified.

INSIDE THE VEHICLE

The maintenance items listed here should be checked on a regular basis, such as when performing periodic maintenance, cleaning the vehicle,
etc.

Item

Reference page

Doors and engine hood

Check that all doors and the engine hood operate smoothly as well as the back door,
trunk lid and hatch. Also make sure that all latches lock securely. Lubricate if neces-
sary. Make sure that the secondary latch keeps the hood from opening when the pri-
mary latch is released. When driving in areas using road salt or other corrosive
materials, check lubrication frequently.

MA-40

Lamps

Clean the headlamps on a regular basis. Make sure that the headlamps, stop lamps,
tail lamps, turn signal lamps, and other lamps are all operating properly and installed
securely. Also check the aim of the headlamps.

—

Tires

Check the pressure with a gauge often and always prior to long distance trips. Adjust
the pressure in all tires, including the spare, to the pressure specified. Check carefully
for damage, cuts or excessive wear.

WT-49

Tire rotation

In the case that Two-Wheel Drive (2WD) and front & rear tires are same size; Tires
should be rotated every 10,000 km (6,000 miles). Tires marked with directional indica-
tors can only be rotated between front and rear. Make sure that the directional indica-
tors point in the direction of wheel rotation after the tire rotation is completed.
In the case that Four-Wheel Drive (4WD) and front & rear tires are same size; Tires
should be rotated every 5,000 km (3,000 miles). Tires marked with directional indica-
tors can only be rotated between front and rear. Make sure that the directional indica-
tors point in the direction of wheel rotation after the tire rotation is completed.
In the case that front tires are different size from rear tires; Tires cannot be rotated.
However, the timing for tire rotation may vary according to your driving habits and the
road surface conditions.

MA-34

Tire Pressure Monitor-
ing System (TPMS)
transmitter components
(if equipped)

Replace the TPMS transmitter grommet seal, valve core and cap when the tires are
replaced due to wear or age.

—

Wheel alignment and
balance

If the vehicle should pull to either side while driving on a straight and level road, or if
you detect uneven or abnormal tire wear, there may be a need for wheel alignment. If
the steering wheel or seat vibrates at normal highway speeds, wheel balancing may
be needed.

FSU-7

RSU-6
MA-34

Windshield

Clean the windshield on a regular basis. Check the windshield at least every six
months for cracks or other damage. Repairs necessary.

—

Wiper blades

Check for cracks or wear if not functioning correctly.

—

Item

Reference page

Accelerator pedal

Check the pedal for smooth operation and make sure that the pedal does not catch or
require uneven effort. Keep the floor mats away from the pedal.

—

Brake pedal

Check the pedal for smooth operation and make sure that it attains the proper distance
from the floor mat when depressed fully. Check the brake booster function. Be sure to
keep the floor mats away from the pedal.

BR-8

Parking brake

Check the parking brake operation regularly. Check that the lever (if equipped) or the
pedal (if equipped) has the proper travel. Also make sure that the vehicle is held se-
curely on a fairly steep hill when only the parking brake is applied.

PB-3

Seat belts

Check that all parts of the seat belt system (for example, buckles, anchors, adjusters
and retractors) operate properly and smoothly, and are installed securely. Check the
belt webbing for cuts, fraying, wear or damage.

MA-40

Revision: 2012 September

2013 MURANO

MA-8

< PERIODIC MAINTENANCE >

GENERAL MAINTENANCE

UNDER THE HOOD AND VEHICLE

The maintenance items listed here should be checked periodically (for example, each time you check the engine oil or refuel.)

Steering wheel

Check for changes in the steering condition, such as excessive play, hard steering or
strange noises. Check that it has the specified play.
Free play: Less than 35 mm (1.38 in)

—

Warning lamps and
chimes

Make sure that all warning lamps and chimes are operating properly.

—

Windshield defogger

Check that the air comes out of the defogger outlets properly and in good quantity when
operating the heater or air conditioner.

—

Windshield wiper and
washer

Check that the wipers and washer operate properly and that the wipers do not streak.

—

Item

Reference page

Item

Reference page

Battery

Except for maintenance free battery; Check the fluid level in each cell. It should be be-
tween the “UPPER” and “LOWER” lines. Vehicles operated in high temperatures or un-
der severe conditions require frequent checks of the battery fluid level.

PG-3

Brake (and clutch) fluid
level(s)

For Manual Transmission (MT) model; Make sure that the brake and clutch fluid levels
are between the “MAX” and “MIN” lines on the reservoir(s).
Except for Manual Transmission (MT) model; Make sure that the brake fluid level is be-
tween the “MAX” and “MIN” lines on the reservoir.

MA-36

Engine coolant level

Check the coolant level when the engine is cold. Make sure that the coolant level is be-
tween the “MAX” and “MIN” lines on the reservoir.

MA-20

Engine drive belt(s)

Make sure that drive belt(s) is/are not frayed, worn, cracked or oily.

MA-20

Engine oil level

Check the level after parking the vehicle (on a level ground) and turning off the engine.

LU-8

Fluid leaks

Check under the vehicle for fuel, oil, water or other fluid leaks after the vehicle has been
parked for a while. Water dripping from the air conditioner after use is normal. If you
should notice any leaks or if fuel fumes are evident, check for cause and have it cor-
rected immediately.

—

Power steering fluid
level and lines

Check the level when the fluid is cold, with the engine off. Check the lines for proper
attachment, leaks, cracks, etc.

MA-38

Windshield washer fluid

Check that there is adequate fluid in the reservoir tank.

—

Revision: 2012 September

2013 MURANO

PERIODIC MAINTENANCE

MA-9

< PERIODIC MAINTENANCE >

PERIODIC MAINTENANCE

FOR NORTH AMERICA

FOR NORTH AMERICA : Introduction of Periodic Maintenance

INFOID:0000000008457468

Two different maintenance schedules are provided, and should be used, depending upon the conditions in
which the vehicle is mainly operated. After 60,000 miles (96,000 km) or 48 months, continue the periodic
maintenance at the same mileage/time intervals.

FOR NORTH AMERICA : Schedule 1

INFOID:0000000008457469

EMISSION CONTROL SYSTEM MAINTENANCE

Abbreviations: R = Replace.

I = Inspect. Correct or replace if necessary.

[ ]: At the mileage intervals only

Schedule 1

Follow Periodic Maintenance Schedule 1 if the driving habits frequently include
one or more of the following driving conditions:
• Repeated short trips of less than 5 miles (8 km).
• Repeated short trips of less than 10 miles (16 km) with outside temperatures

remaining below freezing.

• Operating in hot weather in stop-and-go “rush hour” traffic.
• Extensive idling and/or low speed driving for long distances, such as police, taxi

or door-to-door delivery use.

• Driving in dusty conditions.
• Driving on rough, muddy, or salt spread roads.
• Towing a trailer, using a camper or a car-top carrier.

Emission Control Sys-
tem Maintenance

MA-9

Chassis and Body
Maintenance

MA-9

Schedule 2

Follow Periodic Maintenance Schedule 2 if none of driving conditions shown in
Schedule 1 apply to the driving habits.

Emission Control Sys-
tem Maintenance

MA-11

Chassis and Body
Maintenance

MA-11

MAINTENANCE OPERATION

MAINTENANCE INTERVAL

Reference

Section -

Page or -

Content Title

Perform at number of miles,
kilometers or months, which-
ever comes first.

Miles x 1,000

(km x 1,000)

Months

3.75

(6)

7.50

(12)

11.25

(18)

(24)

18.75

(30)

22.5

(36)

26.25

(42)

(48)

Drive belt

NOTE (1)

MA-20

Air cleaner filter

NOTE (2)

[R]

MA-25

EVAP vapor lines

MA-29

Fuel lines

MA-25

Fuel filter

NOTE (3)

Engine coolant*

NOTE (4)(5)

MA-21

Engine oil

MA-25

Engine oil filter (Use genuine
NISSAN engine oil filter or
equivalent.)

MA-26

Spark plugs (Iridium-tipped
type)

NOTE (6)

Replace every 105,000 miles (168,000 km).

MA-27

Intake & exhaust valve clear-
ance*

NOTE (7)

EM-21

MAINTENANCE OPERATION

MAINTENANCE INTERVAL

Reference

Section -

Page or -

Content Title

Perform at number of miles,
kilometers or months, which-
ever comes first.

Miles x 1,000

(km x 1,000)

Months

33.75

(54)

37.5

(60)

41.25

(66)

(72)

48.75

(78)

52.5

(84)

56.25

(90)

(96)

Drive belt

NOTE (1)

MA-20

Air cleaner filter

NOTE (2)

[R]

MA-25

EVAP vapor lines

MA-29

Revision: 2012 September

2013 MURANO

MA-10

< PERIODIC MAINTENANCE >

PERIODIC MAINTENANCE

NOTE:

(1) After 60,000 miles (96,000 km) or 48 months, inspect every 15,000 miles (24,000 km) or 12 months. Replace the drive belt if found
damaged or if the auto belt tensioner reading reaches maximum limit.

(2) If operating mainly in dusty conditions, more frequent maintenance may be required.

(3) Maintenance-free item. For service procedures, refer to FL section.

(4) First replacement intervals 105,000 miles (168,000 km) or 84 months. After first replacement, replace every 75,000 miles (120,000
km) or 60 months.

(5) Use only Genuine NISSAN Long Life Antifreeze / Coolant (blue) or equivalent with proper mixture ratio of 50% anti-freeze and 50%
demineralized or distilled water. Mixing any other type of coolant or the use of non-distilled water will reduce the life expectancy of the
factory-fill coolant.

(6) Replace spark plug when the spark plug gap exceeds 1.4 mm (0.055 in) even if within specified periodic replacement mileage.

(7) Periodic maintenance is not required. However, if valve noise increases, inspect valve clearance.

* Maintenance items and intervals with “*” are recommended by NISSAN for reliable vehicle operation. The owner need not perform
such maintenance in order to maintain the emission warranty or manufacturer recall liability. Other maintenance items and intervals are
required.

CHASSIS AND BODY MAINTENANCE

Abbreviations: R = Replace. I = Inspect. Correct or replace if necessary.

Fuel lines

MA-25

Fuel filter

NOTE (3)

Engine coolant*

NOTE (4)(5)

MA-21

Engine oil

MA-25

Engine oil filter (Use genuine
NISSAN engine oil filter or
equivalent.)

MA-26

Spark plugs (Iridium-tipped
type)

NOTE (6)

Replace every 105,000 miles (168,000 km).

MA-27

Intake & exhaust valve clear-
ance*

NOTE (7)

EM-21

MAINTENANCE OPERATION

MAINTENANCE INTERVAL

Reference

Section -

Page or -

Content Title

Perform at number of miles,
kilometers or months, which-
ever comes first.

Miles x 1,000

(km x 1,000)

Months

33.75

(54)

37.5

(60)

41.25

(66)

(72)

48.75

(78)

52.5

(84)

56.25

(90)

(96)

MAINTENANCE OPERATION

MAINTENANCE INTERVAL

Reference

Section - Page

or - Content Ti-

tle

Perform at number of miles,
kilometers or months,
whichever comes first.

Miles x 1,000

(km x 1,000)

Months

3.75

(6)

7.50

(12)

11.25

(18)

(24)

18.75

(30)

22.5

(36)

26.25

(42)

(48)

Brake lines & cables

MA-36

Brake pads & rotors

MA-37

Brake fluid

MA-37

CVT fluid

NOTE (1)

MA-30

Transfer oil & differential
gear oil

NOTE (2)

MA-32

MA-33

Steering gear & linkage,
axle & suspension parts

MA-38

MA-39

Tire rotation

NOTE (3)

MA-5

MA-34

Propeller shaft & drive shaft
boots

Exhaust system

In-cabin microfilter

Revision: 2012 September

2013 MURANO

PERIODIC MAINTENANCE

MA-11

< PERIODIC MAINTENANCE >

NOTE:

(1) Use only Genuine NISSAN CVT fluid (NS-3). If towing a trailer, using a camper or a car-top carrier or driving on rough or muddy
roads, inspect CVT fluid deterioration at NISSAN dealers every 60,000 miles (96,000 miles), then change CVT fluid NS-3 if necessary.
And if the inspection is not performed, change (not just inspect) CVT fluid NS-3 every 60,000 miles (96,000 miles). Using transmission
fluid other than Genuine NISSAN CVT Fluid NS-3 will damage the CVT, which is not covered by the NISSAN new vehicle limited
warranty.

(2) If towing a trailer, using a camper or a car-top carrier, or driving on rough or muddy roads, change (not just inspect) oil at every
30,000 miles (48,000 km) or 24 months.

(3) Refer to “Tire rotation” under the “GENERAL MAINTENANCE” heading earlier in this section.

FOR NORTH AMERICA : Schedule 2

INFOID:0000000008457470

EMISSION CONTROL SYSTEM MAINTENANCE

Abbreviations: R = Replace.

I = Inspect. Correct or replace if necessary.

[ ]: At the mileage intervals only

NOTE:

(2) Maintenance-free item. For service procedures, refer to FL section.

MAINTENANCE OPERATION

MAINTENANCE INTERVAL

Reference

Section - Page
or - Content Ti-

tle

Perform at number of miles,
kilometers or months,
whichever comes first.

Miles x 1,000

(km x 1,000)

Months

33.75

(54)

37.5

(60)

41.25

(66)

(72)

48.75

(78)

52.5

(84)

56.25

(90)

(96)

Brake lines & cables

MA-36

Brake pads & rotors

MA-37

Brake fluid

MA-37

CVT fluid

NOTE (1)

MA-30

Transfer oil & differential
gear oil

NOTE (2)

MA-32

MA-33

Steering gear & linkage,
axle & suspension parts

MA-38

MA-39

Tire rotation

NOTE (3)

MA-5

MA-34

Propeller shaft & drive shaft
boots

Exhaust system

In-cabin microfilter

MAINTENANCE OPERATION

MAINTENANCE INTERVAL

Reference Sec-

tion - Page or -

Content Title

Perform at number of miles, kilome-
ters or months, whichever comes first.

Miles x 1,000

(km x 1,000)

Months

7.5

(12)

(24)

22.5

(36)

(48)

37.5

(60)

(72)

52.5

(84)

(96)

Drive belt

NOTE (1)

MA-20

Air cleaner filter

[R]

MA-25

EVAP vapor lines

MA-29

Fuel lines

MA-25

Fuel filter

NOTE (2)

Engine coolant*

NOTE (3)(4)

MA-21

Engine oil

MA-25

Engine oil filter (Use genuine NISSAN
engine oil filter or equivalent.)

MA-26

Spark plugs (Iridium-tipped type)

NOTE (5)

Replace every 105,000 miles (168,000 km).

MA-27

Intake & exhaust valve clearance*

NOTE (6)

EM-21

Revision: 2012 September

2013 MURANO

MA-12

< PERIODIC MAINTENANCE >

PERIODIC MAINTENANCE

(3) First replacement intervals 105,000 miles (168,000 km) or 84 months. After first replacement, replace every 75,000 miles (120,000
km) or 60 months.

(4) Use only Genuine NISSAN Long Life Antifreeze / Coolant (blue) or equivalent with proper mixture ratio of 50% anti-freeze and 50%
demineralized or distilled water. Mixing any other type of coolant or the use of non-distilled water will reduce the life expectancy of the
factory-fill coolant.

(5) Replace spark plug when the spark plug gap exceeds 1.4 mm (0.055 in) even if within specified periodic replacement mileage.

(6) Periodic maintenance is not required. However, if valve noise increases, inspect valve clearance.

CHASSIS AND BODY MAINTENANCE

Abbreviations: R = Replace.

I = Inspect. Correct or replace if necessary.

NOTE:

(1) Using transmission fluid other than Genuine NISSAN CVT Fluid NS-3 will damage the CVT, which is not covered by the NISSAN new
vehicle limited warranty.

(2) Refer to “Tire rotation” under the “GENERAL MAINTENANCE” heading earlier in this section.

FOR MEXICO

FOR MEXICO : Periodic Maintenance

INFOID:0000000008457471

The following tables show the normal maintenance schedule. Depending upon weather and atmospheric con-
ditions, varying road surfaces, individual driving habits and vehicle usage, additional or more frequent mainte-
nance may be required.
Periodic maintenance beyond the last period shown on the tables requires similar maintenance.

ENGINE AND EMISSION CONTROL MAINTENANCE

Abbreviations: I = Inspect and correct or replace as necessary,

R = Replace,

E = Check and correct the engine coolant mixture ratio.

MAINTENANCE OPERATION

MAINTENANCE INTERVAL

Reference Sec-

tion - Page or -

Content Title

Perform at number of miles, kilome-
ters or months, whichever comes
first.

Miles x 1,000

(km x 1,000)

Months

7.5

(12)

(24)

22.5

(36)

(48)

37.5

(60)

(72)

52.5

(84)

(96)

Brake lines & cables

MA-36

Brake pads & rotors

MA-37

Brake fluid

MA-37

CVT fluid

NOTE (1)

MA-30

Transfer oil & differential gear oil

MA-32

MA-33

Steering gear & linkage, axle & sus-
pension parts

MA-38

MA-39

Tire rotation

NOTE (2)

MA-5

MA-34

Propeller shaft & drive shaft boots

Exhaust system

In-cabin microfilter

MAINTENANCE OPERATION

MAINTENANCE INTERVAL

Reference

page

Perform either at number of kilome-
ters (miles) or months, whichever
comes first.

km x 1,000

(Miles x 1,000)

Months

(6)

(12)

(18)

(24)

(30)

(36)

(42)

(48)

Underhood and under vehicle

Intake & exhaust valve clearance

See NOTE (1)

EM-21

Drive belt

See NOTE (2)

MA-20

Engine oil (Use recommended

oil.)

MA-25

Revision: 2012 September

2013 MURANO

PERIODIC MAINTENANCE

MA-13

< PERIODIC MAINTENANCE >

NOTE:

• Maintenance items with “

” should be performed more frequently according to “Maintenance Under Severe Driving Condi-

tions”.

• (1) Periodic maintenance is not required. However, if valve noise increases, check valve clearance.

• (2) Replace the drive belt if found damaged or if the auto belt tensioner reading reaches the maximum limit.

• (3) Use Genuine NISSAN Engine Coolant (blue) or equivalent in its quality, in order to avoid possible aluminium corrosion within the

engine cooling system caused by the use of non-genuine engine coolant. Check and correct the engine coolant mixture ratio every
40,000 km (24,000 miles) or 24 months. First replacement interval is 160,000 km (96,000 miles) or 96 months. After first replacement,
replace every 80,000 km (48,000 miles) or 48 months.

• (4) Maintenance-free item. For service procedures, refer to FL section.

• (5) Replace spark plug when the spark plug gap exceeds 1.4 mm (0.055 in) even if within specified periodic replacement mileage.

CHASSIS AND BODY MAINTENANCE

Abbreviations: I = Inspect and correct or replace as necessary,

R = Replace

Engine oil filter (Use genuine NIS-
SAN engine oil filter or equiva-

lent.)

MA-26

Engine coolant

See NOTE (3)

Cooling system

Fuel lines

Air cleaner filter (Viscous paper

type)

MA-25

Positive crankcase ventilation
(PCV) system

MA-28

Fuel filter (In-tank type)

See NOTE (4)

—

Spark plugs (Iridium-tipped type)

See NOTE (5)

Replace every 100,000 km (60,000 miles)

MA-27

EVAP vapor lines (With carbon
canister)

MA-29

MAINTENANCE OPERATION

MAINTENANCE INTERVAL

Reference

page

Perform either at number of kilome-
ters (miles) or months, whichever
comes first.

km x 1,000

(Miles x 1,000)

Months

(6)

(12)

(18)

(24)

(30)

(36)

(42)

(48)

MAINTENANCE OPERATION

MAINTENANCE INTERVAL

Reference

page

Perform either at number of kilometers
(miles) or months, whichever comes first.

km x 1,000

(Miles x 1,000)

Months

(6)

(12)

(18)

(24)

(30)

(36)

(42)

(48)

Underhood and under vehicle

Brake line & cables

MA-36

Brake fluid (For level & leaks)

MA-36

Brake fluid

MA-37

Exhaust system

MA-30

Power steering fluid & lines
(For level & leaks)

MA-38

CVT fluid (For level & leaks)

See NOTE (1)

MA-30

Transfer gear oil (For level & leaks)

MA-32

Rear differential gear oil (For level &

leaks)

MA-33

Propeller shaft & drive shafts

MA-33

MA-39

Revision: 2012 September

2013 MURANO

MA-14

< PERIODIC MAINTENANCE >

PERIODIC MAINTENANCE

NOTE:

• Maintenance items with “

” should be performed more frequently according to “Maintenance Under Severe Driving Condi-

tions”.

• (1) Use only Genuine NISSAN CVT fluid (NS-2). If towing a trailer, using a camper or a car-top carrier or driving on rough or muddy

roads, inspect CVT fluid deterioration at NISSAN dealers every 100,000 km (60,000 miles), then change CVT fluid NS-2 if necessary.
And if the inspection is not performed, change (not just inspect) CVT fluid NS-2 every 100,000 km (60,000 miles). Using transmis-
sion fluid other than Genuine NISSAN CVT Fluid NS-2 will damage the CVT, which is not covered by the warranty.

MAINTENANCE UNDER SEVERE DRIVING CONDITIONS

The maintenance intervals shown on the preceding pages are for normal operating conditions. If the vehicle is
mainly operated under severe driving conditions as shown below, more frequent maintenance must be per-
formed on the following items as shown in the table.

Severe driving conditions
A — Driving under dusty conditions
B — Driving repeatedly short distances
C — Towing a trailer or caravan
D — Extensive idling
E — Driving in extremely adverse weather conditions or in areas where ambient temperatures are either
extremely low or extremely high
F — Driving in high humidity or mountainous areas
G — Driving in areas using salt or other corrosive areas
H — Driving on rough and/or muddy roads or in the desert
I — Driving with frequent use of braking or in mountainous areas
J — Frequent driving in water

Maintenance operation: Inspect = Inspect. Correct or replace if necessary.

Steering gear & linkage, axle & suspen-

sion parts

MA-38

MA-39

Outside and inside

Wheel alignment (If necessary, rotate &
balance wheels)

FSU-7

RSU-6

MA-34

Brake pads, rotors, drums & linings

Seat belts, buckles, retractors, anchors &
adjusters

MA-40

Foot brake & parking brake
(For free play, stroke & operation)

BR-8

PB-3

Air conditioner filter

VTL-20

VTL-85

MAINTENANCE OPERATION

MAINTENANCE INTERVAL

Reference

page

Perform either at number of kilometers
(miles) or months, whichever comes first.

km x 1,000

(Miles x 1,000)

Months

(6)

(12)

(18)

(24)

(30)

(36)

(42)

(48)

Driving condition

Maintenance item

Mainte-

nance

operation

Maintenance interval

Reference

page

Air cleaner filter (Viscous paper type)

Replace

More frequently

MA-25

Engine oil & engine oil filter

Replace

Every 5,000 km (3,000
miles) or 3 months

MA-25

MA-26

Brake fluid

Replace

Every 20,000 km (12,000
miles) or 12 months

MA-37

Rear differential gear oil

Replace

Every 40,000 km (24,000
miles) or 24 months

MA-34

Revision: 2012 September

2013 MURANO

PERIODIC MAINTENANCE

MA-15

< PERIODIC MAINTENANCE >

Propeller shaft & drive shafts

Inspect

Every 10,000 km (6,000
miles) or 6 months

MA-33

MA-39

Steering gear & linkage, axle & sus-
pension parts

Inspect

Every 20,000 km (12,000
miles) or 12 months

MA-38

MA-39

Brake pads, rotors, drums & linings

Inspect

Every 10,000 km (6,000
miles) or 6 months

Air conditioner filter

Replace

More frequently

VTL-20

VTL-85

Revision: 2012 September

2013 MURANO

MA-16

< PERIODIC MAINTENANCE >

RECOMMENDED FLUIDS AND LUBRICANTS

RECOMMENDED FLUIDS AND LUBRICANTS

FOR NORTH AMERICA

FOR NORTH AMERICA : Fluids and Lubricants

INFOID:0000000008457472

*1: For additional information, see “Engine Oil Recommendation”.

*2: NISSAN recommends Genuine NISSAN Ester oil available at a NISSAN dealer.

*3: Use only Genuine NISSAN CVT Fluid NS-3. Using transmission fluid other than Genuine NISSAN CVT Fluid NS-3 will damage the
CVT, which is not covered by the NISSAN new vehicle limited warranty..

*4: For hot climates, viscosity SAE 90 is suitable for ambient temperatures above 0

C (32

F).

*5: DEXRON

VI type ATF may also be used.

*6: Available in mainland U.S.A. through a NISSAN dealer.

FOR NORTH AMERICA : Engine Oil Recommendation

INFOID:0000000008457473

NISSAN recommends the use of an energy conserving oil in order to improve fuel economy.
Select only engine oils that meet the American Petroleum Institute (API) certification and International Lubri-
cant Standardization and Approval Committee (ILSAC) certification and SAE viscosity standard. These oils
have the API certification mark on the front of the container. Oils which do not have the specified quality label
should not be used as they could cause engine damage.

Capacity (Approximate)

Recommended Fluids/Lubricants

US measure

Imp measure

Liter

Engine oil
Drain and refill

With oil filter
change

4-7/8 qt

4 qt

4.6

Engine oil with API Certification Mark*

1 *2

Viscosity SAE 5W-30*

1 *2

Without oil filter
change

4-1/2 qt

3-3/4 qt

4.3

Dry engine (Overhaul)

5-5/8 qt

4-5/8 qt

5.3

Cooling system

With reservoir
tank

9-5/8 qt

8 qt

9.1

Pre-diluted Genuine NISSAN Long Life Anti-
freeze/Coolant (blue) or equivalent

Reservoir tank

7/8 qt

3/4 qt

0.8

CVT fluid

10-3/4 qt

9 qt

10.2

Genuine NISSAN CVT Fluid NS-3*

Differential gear oil

1-1/8 pt

1 pt

0.55

Genuine NISSAN Differential Oil Hypoid Su-
per GL-5 80W-90 or API GL-5, Viscosity SAE

80W-90*

Transfer oil

5/8 pt

1/2 pt

0.31

Genuine NISSAN Differential Oil Hypoid Su-
per GL-5 80W-90 or API GL-5, Viscosity SAE
80W-90

Power steering fluid (PSF)

1-1/8 qt

7/8 qt

1.0

Genuine NISSAN PSF or equivalent*

Brake fluid

—

Genuine NISSAN Super Heavy Duty Brake

Fluid*

or equivalent DOT 3 (US FMVSS No.

116)

Multi-purpose grease

—

NLGI No. 2 (Lithium soap base)

Windshield washer fluid

—

Genuine NISSAN Windshield Washer Con-
centrate Cleaner & Antifreeze or equivalent

Fuel recommendation

—

Refer to

GI-35, "Fuel"

Revision: 2012 September

2013 MURANO

RECOMMENDED FLUIDS AND LUBRICANTS

MA-17

< PERIODIC MAINTENANCE >

FOR NORTH AMERICA : Anti-Freeze Coolant Mixture Ratio

INFOID:0000000008457474

The engine cooling system is filled at the factory with a pre-diluted mixture of 50% Genuine NISSAN Long Life
Antifreeze/Coolant (blue) and 50% water to provide year-round anti-freeze and coolant protection. The anti-
freeze solution contains rust and corrosion inhibitors. Additional engine cooling system additives are not nec-
essary.

WARNING:

• Never remove the radiator or coolant reservoir cap when the engine is hot. Wait until the engine and

radiator cool down. Serious burns could be caused by high pressure fluid escaping from the radia-
tor.

• The radiator is equipped with a pressure type radiator cap. To prevent engine damage, use only a

genuine NISSAN radiator cap.

CAUTION:

• When adding or replacing coolant, be sure to use only Genuine NISSAN Long Life Antifreeze/Cool-

ant (blue) or equivalent. Genuine NISSAN Long Life Antifreeze/Coolant (blue) is pre-diluted to pro-
vide antifreeze protection to -34

F (-37

C). If additional freeze protection is needed due to weather

where you operate your vehicle, add Genuine NISSAN Long Life Antifreeze/Coolant (blue) concen-
trate following the directions on the container. If an equivalent coolant other than Genuine NISSAN
Long Life Antifreeze/Coolant (blue) is used, follow the coolant manufactur's instructions to maintain
minimum antifreeze protection to -34

F (-37

C). The use of other types of coolant solutions other

than Genuine NISSAN Long Life Antifreeze/Coolant (blue) or equivalent may damage the engine
cooling system.

• Mixing any other type of coolant other than Genuine NISSAN Long Life Antifreeze/Coolant (blue),

including Genuine NISSAN Long Life Antifreeze/Coolant (green), or the use of non-distilled water will
reduce the life expectancy of the factory-fill coolant.

FOR MEXICO

FOR MEXICO : Fluids and Lubricants

INFOID:0000000008457475

API certification mark

API service symbol

JSPIA0014ZZ

Capacity (Approximate)

Recommended Fluids/Lubricants

Liter

Imp measure

Engine oil
Drain and refill

With oil filter change

4.6

4 qt

Genuine NISSAN engine oil*

API grade SL, SM or SN*

ILSAC grade GF-2, GF-3, GF-4 or GF-5*

Viscosity SAE 10W-30

Without oil filter change

4.3

3-3/4 qt

Dry engine (engine overhaul)

5.3

4-5/8 qt

Cooling system (with reservoir)

9.1

8 qt

Genuine NISSAN Engine Coolant (blue) or equiv-

alent*

Reservoir tank

0.8

3/4 qt

Transfer oil

0.31

1/2 pt

Genuine NISSAN Differential Oil Hypoid Super
GL-5 80W-90 or API GL-5, Viscosity SAE 80W-90

Differential gear oil

0.55

1 pt

CVT fluid

10.2

9 qt

Genuine NISSAN CVT fluid NS-2*

Power steering fluid (PSF)

1.0

7/8 qt

Genuine NISSAN PSF or equivalent*

Revision: 2012 September

2013 MURANO

MA-18

< PERIODIC MAINTENANCE >

RECOMMENDED FLUIDS AND LUBRICANTS

*1: For additional information, see “SAE Viscosity Number”.

*2: Use Genuine NISSAN Engine Coolant (blue) or equivalent in its quality, in order to avoid possible aluminum corrosion within the
engine cooling system caused by the use of non-genuine engine coolant.

Note that any repairs for the incidents within the engine cooling system while using non-genuine engine coolant may not be
covered by the warranty even if such incidents occurred during the warranty period.

*3: Use only Genuine NISSAN CVT Fluid NS-2. Using transmission fluid other than Genuine NISSAN CVT fluid NS-2 will damage the
CVT, which is not covered by the warranty.

*4: DEXRON™ VI type ATF may also be used.

FOR MEXICO : SAE Viscosity Number

INFOID:0000000008457476

GASOLINE ENGINE

• 10W-30 is preferable.

5W-30 is also preferable and will improve fuel economy.
If 10W-30 or 5W-30 is not available, select the viscosity, from the
chart, that is suitable for the outside temperature range.

FOR MEXICO : Engine Coolant Mixture Ratio

INFOID:0000000008457477

The engine cooling system is filled at the factory with a high-quality,
year-round and extended life engine coolant. The high quality engine
coolant contains the specific solutions effective for the anti-corrosion
and the anti-freeze function. Therefore, additional cooling system
additives are not necessary.

CAUTION:

• When adding or replacing coolant, be sure to use only Genu-

ine NISSAN Engine Coolant or equivalent in its quality with
the proper mixture ratio. See the examples shown right.

The use of other types of engine coolant may damage the
engine cooling system.
• When checking the engine coolant mixture ratio by the coolant

hydrometer, use the chart below to correct your hydrometer reading (specific gravity) according to coolant
temperature.

Mixed coolant specific gravity

Brake fluid

—

Genuine NISSAN Brake Fluid or equivalent DOT 3
(US FMVSS No. 116)

Multi-purpose grease

—

NLGI No. 2 (Lithium soap base)

Capacity (Approximate)

Recommended Fluids/Lubricants

Liter

Imp measure

JPPIA0003GB

SMA089D

Revision: 2012 September

2013 MURANO

RECOMMENDED FLUIDS AND LUBRICANTS

MA-19

< PERIODIC MAINTENANCE >

Unit: specific gravity

WARNING:

Never remove the radiator cap when the engine is hot. Serious burns could be caused by high pres-
sure fluid escaping from the radiator. Wait until the engine and radiator cool down.

Engine coolant mixture

ratio

Coolant temperature

C (

15 (59)

25 (77)

35 (95)

45 (113)

30%

1.046 - 1.050

1.042 - 1.046

1.038 - 1.042

1.033 - 1.038

50%

1.076 - 1.080

1.070 - 1.076

1.065 - 1.071

1.059 - 1.065

Revision: 2012 September

2013 MURANO

MA-20

< PERIODIC MAINTENANCE >

ENGINE MAINTENANCE

ENGINE MAINTENANCE

DRIVE BELT

DRIVE BELT : Exploded View

INFOID:0000000008457478

DRIVE BELT : Checking

INFOID:0000000008457479

WARNING:

Be sure to perform the this step when engine is stopped.
• Check that the indicator (A) of drive belt auto-tensioner is within the possible use range (C).

NOTE:
• Check the drive belt auto-tensioner indication when the engine is cold.
• When new drive belt is installed, the indicator should be within the range (B) in the figure.

• Visually check entire drive belt for wear, damage or cracks.
• If the indicator is out of the possible use range or belt is damaged, replace drive belt.

DRIVE BELT : Tension Adjustment

INFOID:0000000008457480

Refer to

EM-145, "Drive Belt"

ENGINE COOLANT

ENGINE COOLANT : Inspection

INFOID:0000000008457481

LEVEL

JPBIA1625ZZ

Idler pulley

Drive belt

Power steering oil pump

Drive belt auto-tensioner

Crankshaft pulley

Idler pulley

A/C compressor

Alternator

Indicator

Range when new drive belt is installed

Possible use range

View D

: Engine front

Revision: 2012 September

2013 MURANO

ENGINE MAINTENANCE

MA-21

< PERIODIC MAINTENANCE >

• Check if the reservoir tank engine coolant level is within the “MIN”

to “MAX” when the engine is cool.

• Adjust the engine coolant level if necessary.

CAUTION:

Refill Genuine NISSAN Long Life Antifreeze/Coolant (blue) or
equivalent in its quality mixed with water (distilled or demineral-
ized). Refer to

MA-16, "FOR NORTH AMERICA : Fluids and

Lubricants"

(FOR NORTH AMERICA). or

MA-17, "FOR MEXICO :

Fluids and Lubricants"

(FOR MEXICO).

LEAKAGE

• To check for leakage, apply pressure to the cooling system with the

radiator cap tester (commercial service tool) (A) and radiator cap
tester adapter (commercial service tool) (B).

WARNING:

Never remove radiator cap when engine is hot. Serious burns
could occur from high-pressure engine coolant escaping from
radiator.

CAUTION:

Higher test pressure than specified may cause radiator dam-
age.
NOTE:
In a case that engine coolant decreases, replenish radiator with engine coolant.

• If anything is found, repair or replace damaged parts.

ENGINE COOLANT : Draining

INFOID:0000000008457482

WARNING:

• To avoid being scalded, never change engine coolant when the engine is hot.
• Wrap a thick cloth around radiator cap and carefully remove radiator cap. First, turn radiator cap a

quarter of a turn to release built-up pressure. Then turn radiator cap all the way.

Remove engine under cover.

Open radiator drain plug (1) at the bottom of radiator, and then
remove radiator cap.

When draining all of engine coolant in the system, open water drain plugs on cylinder block. Refer
to

EM-89, "Setting"

Remove reservoir tank if necessary, and drain engine coolant and clean reservoir tank before installing.

Check drained engine coolant for contaminants such as rust, corrosion or discoloration.
If contaminated, flush the engine cooling system. Refer to

CO-13, "Flushing"

ENGINE COOLANT : Refilling

INFOID:0000000008457483

CAUTION:

• Do not reuse O-rings.

: MAX

: MIN

JPBIA0102ZZ

Testing pressure

: Refer to

CO-31, "Radiator"

PBIC5121J

: Vehicle front

JPBIA1684ZZ

Revision: 2012 September

2013 MURANO

Nissan Murano Z51 (2013 year). Manual - part 39