Nissan Murano Z50 (2007 year). Manual - part 140

TURN SIGNAL AND HAZARD WARNING LAMPS

LT-143

C

D

E

F

G

H

I

J

L

M

A

B

LT

Revision: 2006 July

2007 Murano

Any Function of Rear Combination Lamps Does Not Work (One side)

NKS002SY

1. 

CHECK REAR COMBINATION LAMP  DRIVE SIGNAL CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect rear conbination lamp control unit connector and rear combination lamp RH or LH connectors.

3.

Check continuity rear combination lamp control unit harness
connector (A) and rear combination lamp harness connector (B).

4.

Check continuity (short circuit) between rear combination lamp
control unit harness connector (A) and ground.

OK or NG

OK

>> GO TO 2.

NG

>> Repair harness or connector.

2. 

CHECK REAR COMBINATION LAMP CONTROL UNIT GROUND CIRCUIT

Check continuity between rear combination lamp control unit har-
ness connector and ground.

OK or NG

OK

>> Replace rear combination lamp control unit. Refer to 

LT-

184, "REAR COMBINATION LAMP CONTROL UNIT"

 .

NG

>> Repair harness or connector.

Bulb Replacement

NKS001Q4

FRONT TURN SIGNAL LAMP

Refer to 

LT-34, "Bulb Replacement"

  (xenon type headlamp).

Refer to 

LT-63, "Bulb Replacement"

  (conventional type headlamp).

REAR TURN SIGNAL LAMP

Refer to 

LT-184, "Bulb Replacement"

 .

Removal and Installation

NKS001Q6

FRONT TURN SIGNAL LAMP

Refer to 

LT-35, "Removal and Installation"

  (xenon type headlamp).

Refer to 

LT-64, "Removal and Installation"

  (conventional type headlamp).

REAR TURN SIGNAL LAMP

Refer to 

LT-184, "Removal and Installation"

 .

A

B

Continuity

Connector

Terminal

Connector

Terminal

B42

7

RH

B29

1

Yes

5

LH

B24

A

Ground

Continuity

Connector

Terminal

RH

B42

7

No

LH

5

PKIC6977E

Rear combination lamp 

contorol unit connector

Terminal

Ground

Continuity

RH

B42

14

No

LH

13

PKIC6978E

LT-144

LIGHTING AND TURN SIGNAL SWITCH

Revision: 2006 July

2007 Murano

LIGHTING AND TURN SIGNAL SWITCH

PFP:25540

Removal and Installation

NKS001Q8

REMOVAL

1.

Remove instrument driver lower panel and steering column
cover. Refer to 

IP-10, "INSTRUMENT PANEL ASSEMBLY"

 .

2.

While pressing pawls in direction as shown in the figure, pull
lighting and turn signal switch toward driver door and disconnect
from the base.

INSTALLATION

Installation is the reverse order of removal.

PKIB2155E

HAZARD SWITCH

LT-145

C

D

E

F

G

H

I

J

L

M

A

B

LT

Revision: 2006 July

2007 Murano

HAZARD SWITCH

PFP:25290

Removal and Installation

NKS001Q9

REMOVAL

1.

Remove meter lid. Refer to 

DI-24, "Disassembly and Assembly

of Combination Meter"

 .

2.

Disconnect hazard switch connector.

3.

Press pawl on reverse side and remove the hazard switch.

INSTALLATION

Installation is the reverse order of removal.

PKIA2527E

LT-146

COMBINATION SWITCH

Revision: 2006 July

2007 Murano

COMBINATION SWITCH

PFP:25567

Wiring Diagram — COMBSW —

NKS001QA

TKWB2571E

COMBINATION SWITCH

LT-147

C

D

E

F

G

H

I

J

L

M

A

B

LT

Revision: 2006 July

2007 Murano

Combination Switch Reading Function

NKS001QB

For details, refer to 

BCS-3, "COMBINATION SWITCH READING FUNCTION"

 .

Terminals and Reference Values for BCM

NKS002TT

CAUTION:

●

Check combination switch system terminal waveform under the loaded condition with lighting
switch, turn signal and wiper switch OFF not to be fluctuated by overloaded.

●

Turn wiper dial position to 4 except when checking waveform or voltage of wiper dial position.
Wiper dial position can be confirmed on CONSULT-II. Refer to 

LT-152, "DATA MONITOR"

 .

Ter-

minal 

No.

Wire 

color

Signal name

Measuring condition

Reference value

Igni-

tion 

switch

Operation or condition

2

R

Combination 
switch input 5

ON

Lighting, turn, 
wiper switch
(Wiper inter-
mittent dial 
position 4)

OFF

Approx. 0 V

Any of the conditions below

●

Lighting switch 1ST

●

Lighting switch HIGH beam
(Operates only HIGH beam 
switch)

●

Turn signal switch to right

Approx. 1.0 V

Lighting switch 2ND

Approx. 2.0 V

3

P/L

Combination 
switch input 4

ON

Lighting, turn, 
wiper switch
(Wiper inter-
mittent dial 
position 4)

OFF

Approx. 0 V

Front fog lamp switch (Operates 
only front fog lamp switch)

Approx. 0.8 V

Any of the conditions below

●

Lighting switch 2ND

●

Lighting switch PASSING
(Operates only PASSING switch)

●

Turn signal switch to left

Approx. 1.0 V

PKIB4959J

PKIB4953J

PKIB4955J

PKIB4959J

LT-148

COMBINATION SWITCH

Revision: 2006 July

2007 Murano

4

R/G

Combination 
switch input 3

ON

Lighting, turn, 
wiper switch
(Wiper inter-
mittent dial 
position 4)

OFF

Approx. 0 V

Any of the conditions below

●

Lighting switch AUTO

●

Front wiper switch MIST

●

Front wiper switch INT

●

Front wiper switch LO

Approx. 1.0 V

5

R/B

Combination 
switch input 2

ON

Lighting, turn, 
wiper switch

OFF

Approx. 0 V

Any of the conditions below

●

Front washer switch
(Wiper intermittent dial position 4)

●

Rear washer switch
(Wiper intermittent dial position 4)

●

Wiper intermittent dial position 1

●

Wiper intermittent dial position 5

●

Wiper intermittent dial position 6

Approx. 1.0 V

Rear wiper switch ON
(Wiper intermittent dial position 4)

Approx. 0.8 V

Ter-

minal 

No.

Wire 

color

Signal name

Measuring condition

Reference value

Igni-

tion 

switch

Operation or condition

PKIB4959J

PKIB4959J

PKIB4955J

COMBINATION SWITCH

LT-149

C

D

E

F

G

H

I

J

L

M

A

B

LT

Revision: 2006 July

2007 Murano

6

R/W

Combination 
switch input 1

ON

Lighting, turn, 
wiper switch

OFF

Approx. 0 V

Any of the conditions below

●

Front wiper switch HI
(Wiper intermittent dial position 4)

●

Rear wiper switch INT
(Wiper intermittent dial position 4)

●

Wiper intermittent dial position 3

Approx. 1.0 V

Any of the conditions below

●

Wiper intermittent dial position 1 

●

Wiper intermittent dial position 2

Approx. 1.7 V

Any of the conditions below

●

Wiper intermittent dial position 6

●

Wiper intermittent dial position 7

Approx. 0.8 V

11

P/B

Ignition switch 
(ACC)

ACC

—

Battery voltage

32

LG/B

Combination 
switch output 5

ON

Lighting, turn, 
wiper switch

OFF
(Wiper intermittent dial position 4)

Approx. 7.2 V

Any of the conditions below

●

Front fog lamp switch
(Operates only front fog lamp 
switch)
(Wiper intermittent dial position 4)

●

Rear wiper switch ON
(Wiper intermittent dial position 4)

●

Wiper intermittent dial position 1

●

Wiper intermittent dial position 2

●

Wiper intermittent dial position 6

●

Wiper intermittent dial position 7

Approx. 1.0 V

Ter-

minal 

No.

Wire 

color

Signal name

Measuring condition

Reference value

Igni-

tion 

switch

Operation or condition

PKIB4959J

PKIB4952J

PKIB4955J

PKIB4960J

PKIB4956J

LT-150

COMBINATION SWITCH

Revision: 2006 July

2007 Murano

33

G/Y

Combination 
switch output 4

ON

Lighting, turn, 
wiper switch

OFF
(Wiper intermittent dial position 4)

Approx. 7.2 V

Any of the conditions below

●

Lighting switch AUTO
(Wiper intermittent dial position 4)

●

Lighting switch 1ST
(The same result with lighting 
switch 2ND)
(Wiper intermittent dial position 4)

●

Rear wiper switch INT
(Wiper intermittent dial position 4)

●

Wiper intermittent dial position 1

●

Wiper intermittent dial position 5

●

Wiper intermittent dial position 6

Approx. 1.2 V

34

LG/R

Combination 
switch output 3

ON

Lighting, turn, 
wiper switch

OFF
(Wiper intermittent dial position 4)

Approx. 7.2 V

Any of the conditions below

●

Lighting switch 2ND
(Wiper intermittent dial position 4)

●

Lighting switch HI beam
(Operates only HI beam switch)
(Wiper intermittent dial position 4)

●

Rear washer switch
(Wiper intermittent dial position 4)

●

Wiper intermittent dial position 1

●

Wiper intermittent dial position 2

●

Wiper intermittent dial position 3

Approx. 1.2 V

Ter-

minal 

No.

Wire 

color

Signal name

Measuring condition

Reference value

Igni-

tion 

switch

Operation or condition

PKIB4960J

PKIB4958J

PKIB4960J

PKIB4958J

COMBINATION SWITCH

LT-151

C

D

E

F

G

H

I

J

L

M

A

B

LT

Revision: 2006 July

2007 Murano

35

G/B

Combination 
switch output 2

ON

Lighting, turn, 
wiper switch
(Wiper inter-
mittent dial 
position 4)

OFF

Approx. 7.2 V

Any of the conditions below

●

Lighting switch 2ND

●

Lighting switch PASSING
(Operates only PASSING switch)

●

Front wiper switch INT

●

Front wiper switch HI

Approx. 1.2 V

36

L/W

Combination 
switch output 1

ON

Lighting, turn, 
wiper switch
(Wiper inter-
mittent dial 
position 4)

OFF

Approx. 7.2 V

Any of the conditions below

●

Turn signal switch to right

●

Turn signal switch to left

●

Front wiper switch MIST

●

Front wiper switch LO

●

Front washer switch

Approx. 1.2 V

38

R

Ignition switch 
(ON) 

ON

—

Battery voltage

39

L

CAN 

−

 

H

—

—

—

40

Y

CAN 

−

 

L

—

—

—

42

GR

Battery power 
supply

OFF

—

Battery voltage

52

B

Ground

ON

—

Approx. 0 V

55

W/B

Battery power 
supply

OFF

—

Battery voltage

Ter-

minal 

No.

Wire 

color

Signal name

Measuring condition

Reference value

Igni-

tion 

switch

Operation or condition

PKIB4960J

PKIB4958J

PKIB4960J

PKIB4958J

LT-152

COMBINATION SWITCH

Revision: 2006 July

2007 Murano

CONSULT-II Functions (BCM)

NKS001QC

CONSULT-II can display each diagnostic item using the diagnostic test mode shown following.

CONSULT-II BASIC OPERATION

Refer to 

GI-37, "CONSULT-II Start Procedure"

 .

DATA MONITOR
Operation Procedure

1.

Touch “COMB SW” on “SELECT TEST ITEM” screen.

2.

Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.

3.

Touch either “ALL SIGNALS” or “SELECTION FROM MENU” on “SELECT MONITOR ITEM” screen.

4.

When “SELECTION FROM MENU” is selected, touch items to be monitored. When “ALL SIGNALS” is
selected, all the signals will be monitored.

5.

Touch “START”.

6.

Touch “RECORD” while monitoring, then the status of the monitored item can be recorded. To stop
recording, touch “STOP”.

Display Item List

BCM diagnosis part

Diagnosis mode

Description

COMB SW

DATA MONITOR

Displays BCM input data in real time.

ALL SIGNALS

Monitors all the signals.

SELECTION FROM MENU

Selects items and monitors them.

Monitor item

Contents

TURN SIGNAL R

“ON/OFF”

Displays “Turn Right (ON)/Other (OFF)” status, determined from lighting switch signal.

TURN SIGNAL L

“ON/OFF”

Displays “Turn Left (ON)/Other (OFF)” status, determined from lighting switch signal.

HI BEAM SW

“ON/OFF”

Displays status (high beam switch: ON/Others: OFF) of high beam switch judged from lighting 
switch signal.

HEAD LAMP SW 1

“ON/OFF”

Displays status (headlamp switch 2: ON/Others: OFF) of headlamp switch 1 judged from lighting 
switch signal.

HEAD LAMP SW 2

“ON/OFF”

Displays status (headlamp switch 2: ON/Others: OFF) of headlamp switch 2 judged from lighting 
switch signal.

LIGHT SW 1ST

“ON/OFF”

Displays status (lighting switch 1ST or 2ND position: ON/Others: OFF) of lighting switch judged 
from lighting switch signal.

PASSING SW

“ON/OFF”

Displays status (flash-to-pass switch: ON/Others: OFF) of flash-to-pass switch judged from lighting 
switch signal.

AUTO LIGHT SW

“ON/OFF”

Displays “Auto light switch (ON)/Other (OFF)” status, determined from lighting switch signal.

FR FOG SW

“ON/OFF”

Displays “Front fog lamp switch (ON)/Other (OFF)” status, determined from lighting switch signal.

FR WIPER HI

“ON/OFF”

Displays “Front Wiper HI (ON)/Other (OFF)” status, determined from wiper switch signal.

FR WIPER LOW

“ON/OFF”

Displays “Front Wiper LOW (ON)/Other (OFF)” status, determined from wiper switch signal.

FR WIPER INT

“ON/OFF”

Displays “Front Wiper INT (ON)/Other (OFF)” status, determined from wiper switch signal.

FR WASHER SW

“ON/OFF”

Displays “Front Washer Switch (ON)/Other (OFF)” status, determined from wiper switch signal.

INT VOLUME

“1 - 7” 

Displays intermittent operation knob setting (1 - 7), determined from wiper switch signal.

RR WIPER ON

“ON/OFF”

Displays “rear Wiper (ON)/Other (OFF)” status as judged from wiper switch signal.

RR WIPER INT

“ON/OFF”

Displays “rear Wiper INT (ON)/Other (OFF)” status as judged from wiper switch signal.

RR WASHER SW

“ON/OFF”

Displays “rear Washer Switch (ON)/Other (OFF)” status as judged from wiper switch signal.

COMBINATION SWITCH

LT-153

C

D

E

F

G

H

I

J

L

M

A

B

LT

Revision: 2006 July

2007 Murano

Combination Switch Inspection

NKS002TU

1. 

SYSTEM CHECK

Referring to table below, check which system malfunctioning switch belongs to.

>> Check the system to which malfunctioning switch belongs, and GO TO 2.

2. 

SYSTEM CHECK

With CONSULT-II

CAUTION:

If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication. 
1.

Connect CONSULT-II, and select “COMB SW” on “SELECT
TEST ITEM” screen.

2.

Select “DATA MONITOR”.

3.

Select “START”, and confirm that other switches in malfunction-
ing system operate normally.
Example: When the auto light switch is malfunctioning, confirm
that “FRONT WIPER LOW” and “FRONT WIPER INT” in system
3, to which the auto light switch belongs, turn ON-OFF normally.

Without CONSULT-II

Operating combination switch, and confirm that other switches in malfunctioning system operate normally.
Example: When the auto light switch is malfunctioning, confirm that FRONT WIPER LOW and FRONT WIPER
INT in system 3, to which the auto light switch belongs, operate normally.

Check results

Other switches in malfunctioning system operate normally.>>Replace lighting switch or wiper switch.
Other switches in malfunctioning system do not operate normally.>>GO TO 3.

System 1

System 2

System 3

System 4

System 5

—

FR WASHER

FR WIPER LO

TURN LH

TURN RH

FR WIPER HI

—

FR WIPER INT

PASSING

HEAD LAMP1

INT VOLUME 1

RR WASHER

—

HEAD LAMP2

HI BEAM

RR WIPER INT

INT VOLUME 3

AUTO LIGHT

—

LIGHT SW 1ST

INT VOLUME 2

RR WIPER ON

—

FR FOG

—

PKIA7602E

LT-154

COMBINATION SWITCH

Revision: 2006 July

2007 Murano

3. 

CHECK HARNESS

1.

Turn ignition switch OFF.

2.

Disconnect BCM connector and combination switch connector.

3.

Check for continuity between BCM harness connector of the suspect system and the corresponding com-
bination switch harness connector.

4.

Check for continuity between BCM harness connector in suspect malfunctioning system and ground.

OK or NG

OK

>> GO TO 4.

NG

>> Check harness between BCM and combination switch for open or short circuit.

Suspect 

system

BCM

Combination switch

Continuity

Connector

Terminal

Connector

Terminal

1

M1

Input 1

6 

M29

6 

Yes

Output 1

36 

1 

2

Input 2

5

7 

Output 2

35

2

3

Input 3

4 

10 

Output 3

34 

3 

4

Input 4

3 

9 

Output 4

33

4 

5

Input 5

2 

8 

Output 5

32

5

Suspect 

system

BCM

connector

Terminal

Continuity

1

M1

Input 1

6

Ground

No

Output 1

36 

2

Input 2

5 

Output 2

35 

3

Input 3

4

Output 3

34 

4

Input 4

3

Output 4

33 

5

Input 5

2 

Output 5

32

PKIA7235E

PKIA7506E

COMBINATION SWITCH

LT-155

C

D

E

F

G

H

I

J

L

M

A

B

LT

Revision: 2006 July

2007 Murano

4. 

CHECK BCM OUTPUT TERMINAL

1.

Turn lighting switch and wiper switch OFF position.

2.

Set wiper dial position 4.

3.

Connect BCM connector and combination switch connector.

4.

Turn ignition switch ON.

5.

Check BCM output terminal voltage waveform of suspect mal-
functioning system.

OK or NG

OK

>> Open circuit in combination switch, GO TO 5.

NG

>> Replace BCM. Refer to 

BCS-14, "Removal and Installation of BCM"

 .

5. 

CHECK COMBINATION SWITCH

Referring to table below, perform combination switch inspection.

>> INSPECTION END

Removal and Installation

NKS001QE

For details, refer to 

LT-144, "LIGHTING AND TURN SIGNAL SWITCH"

 .

Suspect 

system

(+) 

(

−

)

Reference value

Combination 

switch 

connector

Terminal 

1

M29

1

Ground

2

2 

3

3

4

4

5

5

PKIC1020E

PKIB4960J

Procedure

1

2

3

4

5

6

7

Replace 

lighting 

switch

Confirm 
check 
results

OK

INSPECTION END

Confirm 
check 
results

OK

INSPECTION END

Confirm 
check 
results

OK

INSPECTION END

NG

Replace wiper switch

NG

Replace switch base

NG

Confirm symptom again

LT-156

STOP LAMP

Revision: 2006 July

2007 Murano

STOP LAMP

PFP:26550

Component Parts and Harness Connector Location

NKS002T0

System Description

NKS002T2

OUTLINE

Power is supplied at all times

●

through 10A fuse [No. 20, located in fuse block (J/B)]

●

to rear combination lamp control unit terminal 9 and

●

to stop lamp switch terminal 3,

●

through 10A fuse [No. 21, located in fuse block (J/B)]

●

to combination meter terminal 21.

With the ignition switch in the ON or START position, power is supplied

●

through 10A fuse [No. 12, located in fuse block (J/B)]

●

to rear combination lamp control unit terminal 16,

●

through 10A fuse [No. 14, located in fuse block (J/B)]

●

to combination meter terminal 20.

Ground is supplied

●

to rear combination lamp control unit terminals 12

●

through grounds B7 and B20,

●

to combination meter terminals 22, 23 and 24

●

through grounds M14 and M78.

STOP LAMP OPERATION

When the stop lamp switch is depressed supplies power

PKIC7600E

STOP LAMP

LT-157

C

D

E

F

G

H

I

J

L

M

A

B

LT

Revision: 2006 July

2007 Murano

●

through stop lamp switch terminal 3

●

to rear combination lamp control unit terminal 2

●

to high-mounted stop lamp terminal 1 and

●

to unified meter and A/C amp..

When receiving the stop lamp signal, rear combination lamp control unit detects the stop lamp ON, then rear
combination lamp control unit outputs the rear combination lamp drive signal RH and LH (stop lamp output).
Rear combination lamp control unit supplies power

●

through rear combination lamp control unit terminal 7

●

to rear combination lamp RH terminal 1,

●

through rear combination lamp control unit terminal 5

●

to rear combination lamp LH terminal 1.

Ground is supplied

●

to high-mounted stop lamp terminal 2

●

through grounds B7 and B20,

●

to rear combination lamp RH terminal 4

●

through rear combination lamp control unit terminal 14,

●

to rear combination lamp LH terminal 4

●

through rear combination lamp control unit terminal 13.

With power and ground supplied, stop lamp and high-mounted stop lamp illuminate.

LT-158

STOP LAMP

Revision: 2006 July

2007 Murano

Schematic

NKS002Q7

TKWB2572E