Nissan Murano Z50 (2004 year). Manual

ILLUMINATION

LT-201

Revision: 2004 November

2004 Murano

TKWA1705E

ILLUMINATION

LT-203

Revision: 2004 November

2004 Murano

Removal and Installation

AKS005MB

ILLUMINATION CONTROL SWITCH

Remove the meter lid. Refer to

DI-29, "Disassembly and Assem-

bly of Combination Meter"

in “DRIVER INFORMATION SYS-

TEM (DI)” section.

Remove the illumination control switch fixing screws and
remove the unit from the meter lid.

CONSOLE POCKET LAMP

Remove the instrument stay cover. Refer to

IP-11, "Removal

and Installation"

in “INSTRUMENT PANEL (IP)” section.

Turn the bulb socket counterclockwise and unlock it.

GLOVE BOX LAMP

Remove the instrument passenger lower panel. Refer to

IP-11,

"Removal and Installation"

in “INSTRUMENT PANEL (IP)” sec-

tion.

Turn the bulb socket counterclockwise and unlock it.

COIN BOX ILLUMINATION

Remove the A/T console finisher. Refer to

IP-17, "CENTER

CONSOLE ASSEMBLY"

in “INSTRUMENT PANEL (IP)” sec-

tion.

Turn the bulb socket counterclockwise and unlock it.

PKIA2543E

Console pocket lamp

: 12V - 2W

PKIA2544E

Glove box lamp

: 12V - 1.4W

PKIA2545E

Coin box illumination

: 12V - 1.4W

PKIA2947E

LT-204

BULB SPECIFICATIONS

Revision: 2004 November

2004 Murano

BULB SPECIFICATIONS

PFP:26297

Headlamp

AKS005ME

Exterior Lamp

AKS005MF

Interior Lamp/Illumination

AKS005MG

Item

Wattage (W)

High/Low (Halogen type)

65/55 (HB5)

High/Low (Xenon type)

35 (D2R)

Item

Wattage (W)

Front combination lamp

Front turn signal lamp

21 (amber)

Parking lamp

3.8

Front side marker lamp

3.8

Rear combination lamp

Stop/Tail lamp

21/5

Rear turn signal lamp

Rear side marker lamp

Front fog lamp

51 (HB4)

Back-up lamp

License plate lamp

High-mounted stop lamp (back door mount)

LED

Item

Wattage (W)

Map lamp

Room lamp

Personal lamp

Luggage room lamp

Step lamp

2.7

Glove box lamp

1.4

Vanity mirror lamp

Ignition key hole illumination

1.4

Console pocket lamp

1.4

Coin box illumination

1.4

LU-2

PRECAUTIONS

Revision: 2004 November

2004 Murano

PRECAUTIONS

PFP:00001

Precautions for Liquid Gasket

ABS004RE

LIQUID GASKET APPLICATION PROCEDURE

Remove old liquid gasket adhering to the liquid gasket application surface and the mating surface.

●

Remove liquid gasket completely from the liquid gasket application surface, mounting bolts, and bolt
holes.

Wipe the liquid gasket application surface and the mating surface with white gasoline (lighting and heating
use) to remove adhering moisture, grease and foreign materials.

Attach liquid gasket tube to tube presser [SST: WS39930000
(

—

)].

Use Genuine RTV Silicone Sealant or equivalent. Refer to

●

Within 5 minutes of liquid gasket application, install the mating
component.

●

If liquid gasket protrudes, wipe it off immediately.

●

Do not retighten mounting bolts or nuts after the installation.

●

After 30 minutes or more have passed from the installation, fill
engine oil and engine coolant.

EMA0622D

PREPARATION

LU-3

Revision: 2004 November

2004 Murano

PREPARATION

PFP:00002

Special Service Tools

ABS003MQ

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Commercial Service Tools

ABS003MR

Tool number
(Kent-Moore No.)
Tool name

Description

ST25051001
(J25695-1)
Oil pressure gauge

Measuring oil pressure
Maximum measuring range: 2,452 kPa (25

kg/cm

, 356 psi)

ST25052000
(J25695-2)
Hose

Adapting oil pressure gauge to upper oil pan

KV10115801
(J38956)
Oil filter wrench

Removing oil filter

WS39930000
(

—

)

Tube presser

Pressing the tube of liquid gasket

NT050

S-NT559

S-NT375

NT052

Tool name

Description

Power tools

Loosening nuts and bolts

Deep socket

Removing and installing oil pressure switch
a: 24 mm (0.94 in)

PBIC0190E

PBIC2072E

LUBRICATION SYSTEM

LU-5

Revision: 2004 November

2004 Murano

System Drawing

ABS0035O

PBIC2689E

LU-6

ENGINE OIL

Revision: 2004 November

2004 Murano

ENGINE OIL

PFP:KLA92

Inspection

ABS0035P

ENGINE OIL LEVEL

NOTE:
Before starting engine, put vehicle horizontally and check the engine oil level. If engine is already started, stop
it and allow 10 minutes before checking.

Pull out oil level gauge and wipe it clean.

Insert oil level gauge and make sure the engine oil level is within
the range shown in the figure.

If it is out of range, adjust it.

ENGINE OIL APPEARANCE

●

Check engine oil for white turbidity or heavy contamination.

●

If engine oil becomes turbid and white, it is highly probable that it is contaminated with engine coolant.
Repair or replace damaged parts.

ENGINE OIL LEAKAGE

Check for engine oil leakage around the following areas:

●

Oil pans (lower and upper)

●

Oil pan drain plug

●

Oil pressure switch

●

Oil filter

●

Oil cooler

●

Water pump cover

●

Chain tensioner cover

●

Intake valve timing control cover and intake valve timing control solenoid valve

●

Mating surface between cylinder block and cylinder head

●

Mating surface between cylinder head and rocker cover

●

Mating surface between front timing chain case and rear timing chain case

●

Mating surface between rear timing chain case and cylinder block

●

Crankshaft oil seals (front and rear)

PBIC0249E

ENGINE OIL

LU-7

Revision: 2004 November

2004 Murano

OIL PRESSURE CHECK

WARNING:

●

Be careful not to burn yourself, as engine oil may be hot.

●

Oil pressure check should be done in “Parking position”.

Check the engine oil level. Refer to

LU-6, "ENGINE OIL LEVEL"

Remove splash guard (RH).

Disconnect harness connector at oil pressure switch, and
remove oil pressure switch using deep socket (commercial ser-
vice tool)

CAUTION:

Do not drop or shock oil pressure switch.

Install pressure gauge and hose [SST].

Start engine and warm it up to normal operating temperature.

Check the engine oil pressure with engine running under no-load.

NOTE:
When engine oil temperature is low, the engine oil pressure becomes high.

Engine oil pressure [Engine oil temperature at 80

C (176

F)]

If difference is extreme, check engine oil passage and oil pump for engine oil leaks.

After the inspections, install oil pressure switch as follows:

Remove old liquid gasket adhering to oil pressure switch and engine.

Apply liquid gasket and tighten oil pressure switch to the specification.
Use Genuine RTV Silicone Sealant or equivalent. Refer to

GI-47, "RECOMMENDED CHEMICAL

PRODUCTS AND SEALANTS"

SLC240B

SLC926

Engine speed

rpm

Approximate discharge pressure

kPa (kg/cm

, psi)

Idle speed

More than 98 (1.0, 14)

2,000

More than 294 (3.0, 43)

: 14.8 N·m (1.5 kg-m, 11 ft-lb)

LU-8

ENGINE OIL

Revision: 2004 November

2004 Murano

Changing Engine Oil

ABS0035Q

WARNING:

●

Be careful not to burn yourself, as engine oil may be hot.

●

Prolonged and repeated contact with used engine oil may cause skin cancer; try to avoid direct
skin contact with used engine oil. If skin contact is made, wash thoroughly with soap or hand
cleaner as soon as possible.

Warm up engine, put vehicle horizontally and check for engine oil leakage from engine components. Refer
to

LU-6, "ENGINE OIL LEAKAGE"

Stop engine and wait for 10 minutes.

Loosen oil filler cap, and then remove drain plug.

Drain engine oil.

Install drain plug with new washer. Refer to

EM-28, "OIL PAN AND OIL STRAINER"

CAUTION:

Be sure to clean drain plug and install with new washer.

Refill with new engine oil.
Engine oil specification and viscosity:
Refer to

Engine oil capacity (Approximate):

Unit:

(US qt, Imp qt)

CAUTION:

●

When filling engine oil, do not pull out oil level gauge.

●

The refill capacity depends on the engine oil temperature and drain time. Use these specifica-
tions for reference only.

●

Always use oil level gauge to determine the proper amount of engine oil in engine.

Warm up engine and check area around drain plug and oil filter for engine oil leakage.

Stop engine and wait for 10 minutes.

Check the engine oil level. Refer to

LU-6, "ENGINE OIL LEVEL"

Oil pan drain plug:

:34.3 N·m (3.5 kg-m, 25 ft-lb)

Drain and refill

With oil filter change

4.0 (4-1/4, 3-1/2)

Without oil filter change

3.7 (3-7/8, 3-1/4)

Dry engine (Overhaul)

5.0 (5-1/4, 4-3/8)

OIL FILTER

LU-9

Revision: 2004 November

2004 Murano

OIL FILTER

PFP:15208

Removal and Installation

ABS0035R

REMOVAL

Remove splash guard (RH).

Using oil filter wrench [SST], remove oil filter.

CAUTION:

●

Oil filter is provided with relief valve. Use genuine Nissan
oil filter or equivalent.

●

Be careful not to get burned when engine and engine oil
may be hot.

●

When removing, prepare a shop cloth to absorb any
engine oil leakage or spillage.

●

Do not allow engine oil to adhere to drive belts.

●

Completely wipe off any engine oil that adheres to engine
and vehicle.

INSTALLATION

Remove foreign materials adhering to oil filter installation surface.

Apply engine oil to the oil seal contact surface of new oil filter.

Screw oil filter manually until it touches the installation surface,
then tighten it by 2/3 turn. Or tighten to specification.

INSPECTION AFTER INSTALLATION

Check the engine oil level. Refer to

LU-6, "ENGINE OIL"

Start engine, and check there is no leak of engine oil.

Stop engine and wait for 10 minutes.

Check the engine oil level and add engine oil. Refer to

LU-6, "ENGINE OIL"

SMA039D

SMA010

Oil filter:

: 17.6 N·m (1.8 kg-m, 13 ft-lb)

SMA229B

LU-10

OIL COOLER

Revision: 2004 November

2004 Murano

OIL COOLER

PFP:21305

Removal and Installation

ABS0035S

WARNING:

Be careful not to get burn yourself, as engine oil and engine coolant may be hot.

REMOVAL

NOTE:
When remove oil cooler only, step 2 is unnecessary.

Remove splash guard (RH).

Drain engine coolant from radiator and cylinder block. Refer to

CO-9, "Changing Engine Coolant"

and

EM-111, "DISASSEMBLY"

NOTE:
Perform this step when removing water pipes.

Remove oil filter. Refer to

LU-9, "OIL FILTER"

CAUTION:

Do not spill engine oil on drive belt.

Disconnect water hoses from oil cooler.

●

When removing oil cooler only, pinching water hoses near oil cooler to prevent engine coolant spilling.

CAUTION:

●

Perform this step when engine is cold.

●

Do not spill engine coolant on drive belts.

Connector bolt

Copper gasket

Water drain plug

Water pipe

Bracket

Water hose

Relief valve

O-ring

Oil cooler

10.

Connector bolt

11.

Oil filter

12. Water hose

13.

Water pipe

14. Clamp

15. Water hose

16.

Clamp

PBIC2690E

OIL COOLER

LU-11

Revision: 2004 November

2004 Murano

Remove connector bolt, and remove oil cooler.

CAUTION:

Do not spill engine oil to rubber parts such as drive belts and engine mounting insulator.

Remove water pipes, as necessary.

INSPECTION AFTER REMOVAL
Oil Cooler

Check oil cooler for cracks. Check oil cooler for clogging by blowing through engine coolant inlet. If necessary,
replace oil cooler.

Relief Valve

Inspect relief valve for movement, cracks and breaks by pushing the ball. If replacement is necessary, remove
relief valve by prying it out with suitable tool. Install new relief valve in place by tapping it.

INSTALLATION

Note the following, and install in the reverse order of removal.

●

Make sure that no foreign objects are adhering to the installation surfaces of oil cooler and oil pan (upper).

●

Align cutout on oil cooler with protrusion on oil pan (upper) side,
and tighten connector bolt.

INSPECTION AFTER INSTALLATION

Check the engine oil level and the engine coolant level and add engine oil and engine coolant. Refer to

LU-6, "ENGINE OIL"

an d

CO-9, "ENGINE COOLANT"

Start engine, and check there is no leaks of engine oil or engine coolant.