Nissan Murano Z50 (2004 year). Manual - part 184

 

  Index      Manuals     Nissan Murano Z50 (2004 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     182      183      184      185     ..

 

 

Nissan Murano Z50 (2004 year). Manual - part 184

 

 

INTERIOR ROOM LAMP

LT-185

C

D

E

F

G

H

I

J

L

M

A

B

LT

Revision: 2004 November

2004 Murano

ACTIVE TEST
Operation Procedure

1.

Touch “INT LAMP” on “SELECT TEST ITEM” screen.

2.

Touch “ACTIVE TEST” on “SELECT DIAG MODE” screen.

3.

Touch item to be tested and check operation of the selected item.

4.

During the operation check, touching “BACK” deactivates the operation.

Display Item List

Room Lamp Does Not Illuminate

AKS00AMJ

1. 

CHECK EACH SWITCH

Select “BCM” on CONSULT-II. With “INT LAMP” data monitor to
make sure switches listed in display item list turn ON-OFF linked
with switch operation. Refer to 

LT-184, "Display Item List"

      for

switches and their functions.

OK or NG

OK

>> GO TO 2.

NG

>> Inspect malfunctioning switch system.

DOOR SW - DR

“ON/OFF”

Displays status of the driver door as judged from the driver door switch signal. (Door is open: ON/
Door is closed: OFF)

DOOR SW - AS

“ON/OFF”

Displays status of the passenger door as judged from passenger door switch signal. (Door open 
(ON)/Door closed (OFF))

DOOR SW - RR

“ON/OFF”

Displays status of rear door as judged from the rear door switch (RH) signal. (Door is open: ON/
Door is closed: OFF)

DOOR SW - RL

“ON/OFF”

Displays status of rear door as judged from the rear door switch (LH) signal. (Door is open: ON/
Door is closed: OFF)

BACK DOOR SW

“ON/OFF”

Displays status of the back door as judged from back door switch signal. (Door open (ON)/Door 
closed (OFF))

KEY CYL LK - SW

“ON/OFF”

Displays “Door locked (ON) status, determined from key cylinder lock switch in driver door.

KEY CYL UN - SW

“ON/OFF”

Displays “Door unlocked (OFF) status, determined from key cylinder lock switch in driver door.

CDL LOCK SW

“ON/OFF”

Displays “Door locked (ON)/Door unlocked (OFF) status, determined from locking detection 
switch in driver door.

CDL UNLOCK SW

“ON/OFF”

Displays “Door unlocked (OFF)” status, determined from locking detection switch in passenger 
door.

KEYLESS LOCK

“ON/OFF”

Displays “Locked (ON)/Other (OFF)” status, determined from lock signal.

KEYLESS UNLOCK

“ON/OFF”

Displays “Unlocked (ON)/Other (OFF)” status, determined from unlock signal.

Monitor item 

Contents

Test item

Description

INT LAMP

Interior room  lamp can be operated by any ON-OFF operations.

IGN ILLUM

Ignition key hole illumination can be operated by ON

 OFF operation.

PKIA6365E

LT-186

INTERIOR ROOM LAMP

Revision: 2004 November

2004 Murano

2. 

CHECK WITH ACTIVE TEST

1.

Select “BCM” on CONSULT-II. Select “INT LAMP” active test.

2.

When room lamp switch is in “DOOR” position, use active test to
make sure room lamp operates.

OK or NG

OK

>> Replace BCM. Refer to 

BCS-14, "Removal and Installa-

tion of BCM"

 .

NG

>> GO TO 3.

3. 

CHECK POWER SUPPLY TO ROOM LAMP 

1.

Turn ignition switch OFF.

2.

Disconnect room lamp connector.

3.

Turn ignition switch ON.

4.

Check voltage between room lamp harness connector R9 termi-
nal 2 (Y) and ground.

OK or NG

OK

>> GO TO 4.

NG

>> GO TO 6.

4. 

CHECK ROOM LAMP 

Check continuity between room lamp terminals.

OK or NG

OK

>> GO TO 5.

NG

>> Check bulb or replace room lamp.

5. 

CHECK POWER SUPPLY CIRCUIT FOR ROOM LAMP

1.

Disconnect BCM connector.

2.

Check continuity between BCM harness connector M35 terminal
48 (R) and room lamp harness connector R9 terminal 1 (R).

OK or NG

OK

>> Replace BCM. Refer to 

BCS-14, "Removal and Installa-

tion of BCM"

 .

NG

>> Repair harness or connector.

PKIA6366E

2 (Y) - Ground

: Battery voltage should exist.

PKIA6367E

Terminal

Condition

Continuity

Room lamp

1

Room lamp switch is ON.

Yes

Room lamp switch is OFF.

No

PKIA6368E

Continuity should exist.

PKIA6369E

INTERIOR ROOM LAMP

LT-187

C

D

E

F

G

H

I

J

L

M

A

B

LT

Revision: 2004 November

2004 Murano

6. 

CHECK GROUND CIRCUIT FOR ROOM LAMP

1.

Disconnect BCM connector and room lamp connector.

2.

Check continuity between BCM harness connector M35 terminal
41 (P) and room lamp harness connector R9 terminal 2 (Y).

OK or NG

OK

>> Replace BCM. Refer to 

BCS-14, "Removal and Installa-

tion of BCM"

 .

NG

>> Repair harness or connector.

Personal Lamp Does Not Illuminate

AKS00AMK

1. 

CHECK EACH SWITCH

Select “BCM” on CONSULT-II. With “INT LAMP” data monitor to
make sure switches listed in display item list turn ON-OFF linked
with switch operation. Refer to 

LT-184, "Display Item List"

      for

switches and their functions.

OK or NG

OK

>> GO TO 2.

NG

>> Inspect malfunctioning switch system.

2. 

CHECK WITH ACTIVE TEST

1.

Select “BCM” on CONSULT-II. Select “INT LAMP” active test.

2.

When personal lamp switch is in “DOOR” position, use active
test to make sure personal lamp operates.

OK or NG

OK

>> Replace BCM. Refer to 

BCS-14, "Removal and Installa-

tion of BCM"

 .

NG

>> GO TO 3.

41 (P) - 2 (Y)

: Continuity should exist.

PKIA6370E

PKIA6365E

PKIA6366E

LT-188

INTERIOR ROOM LAMP

Revision: 2004 November

2004 Murano

3. 

CHECK PERSONAL LAMP INPUT 

1.

Turn ignition switch OFF.

2.

Disconnect personal lamp connectors.

3.

Turn ignition switch ON.

4.

Check voltage between personal lamp RH harness connector
R10 terminal 1 (Y) and ground.

5.

Check voltage between personal lamp LH harness connector
R8 terminal 1 (Y) and ground.

OK or NG

OK

>> GO TO 4.

NG

>> GO TO 6.

4. 

CHECK PERSONAL LAMP 

1.

Disconnect personal lamp connector.

2.

Check continuity between personal lamp terminals.

OK or NG

OK

>> GO TO 5.

NG

>> Check bulb or replace personal lamp.

5. 

CHECK PERSONAL LAMP CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect BCM connector.

3.

Check continuity between BCM harness connector M35 terminal
48 (R) and personal lamp RH harness connector R10 terminal 3
(R).

4.

Check continuity between BCM harness connector M35 terminal
48 (R) and personal lamp LH harness connector terminal 3 (R).

OK or NG

OK

>> Replace BCM. Refer to 

BCS-14, "Removal and Installation of BCM"

 .

NG

>> Repair harness or connector.

1 (Y) - Ground

: Battery voltage should exist.

1 (Y) - Ground

: Battery voltage should exist.

PKIA6371E

Terminal

Condition

Continuity

Personal lamp

1

Personal lamp switch is ON.

Yes

Personal lamp switch is OFF.

No

PKIA6372E

48 (R) - 3 (R)

: Continuity should exist.

48 (R) - 3 (R)

: Continuity should exist.

PKIA6373E

INTERIOR ROOM LAMP

LT-189

C

D

E

F

G

H

I

J

L

M

A

B

LT

Revision: 2004 November

2004 Murano

6. 

CHECK PERSONAL LAMP CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect BCM connector and personal lamp connector.

3.

Check continuity between BCM harness connector M35 terminal
41 (P) and personal lamp RH harness connector R10 terminal 1
(Y).

4.

Check continuity between BCM harness connector M35 terminal
41 (P) and personal lamp LH harness connector R8 terminal 1
(Y).

OK or NG

OK

>> Replace BCM. Refer to 

BCS-14, "Removal and Installation of BCM"

 .

NG

>> Repair harness or connector.

Ignition Key Hole Illumination Does Not Illuminate

AKS00AML

1. 

CHECK BULB

Check bulb of lamp which does not operate.

OK or NG

OK

>> GO TO 2.

NG

>> Replace bulb.

2. 

CHECK EACH SWITCH

Select “BCM” on CONSULT-II. With “INT LAMP” data monitor to
make sure switches listed in display item list turn ON-OFF linked
with switch operation. Refer to 

LT-184, "Display Item List"

      for

switches and their functions.

OK or NG

OK

>> GO TO 3.

NG

>> Inspect malfunctioning switch system.

3. 

CHECK WITH ACTIVE TEST

1.

Select “BCM” on CONSULT-II. Select “INT LAMP”.

2.

Select “IGN ILLUM” active test to make sure lamp operates.

OK or NG

OK

>> Replace BCM.Refer to 

BCS-14, "Removal and Installa-

tion of BCM"

 .

NG

>> GO TO 4.

41 (P) - 1 (Y)

: Continuity should exist.

41 (P) - 1 (Y)

: Continuity should exist.

PKIA6374E

PKIA6365E

PKIA6375E

LT-190

INTERIOR ROOM LAMP

Revision: 2004 November

2004 Murano

4. 

CHECK POWER SUPPLY TO IGNITION KEY HOLE ILLUMINATION

1.

Turn ignition switch OFF.

2.

Disconnect ignition key hole illumination connector.

3.

Turn ignition switch ON.

4.

Check voltage between ignition key hole illumination harness
connector M40 terminal 1 (P) and ground.

OK or NG

OK

>> GO TO 6.

NG

>> GO TO 5.

5. 

CHECK POWER SUPPLY CIRCUIT FOR IGNITION KEY HOLE ILLUMINATION

1.

Turn ignition switch OFF.

2.

Disconnect BCM connector and key hole illumination connector.

3.

Check continuity between BCM harness connector M35 terminal
41 (P) and key hole illumination harness connector M40 terminal
1 (P). 

OK or NG

OK

>> Replace BCM. Refer to 

BCS-14, "Removal and Installa-

tion of BCM"

 .

NG

>> Repair harness or connector.

6. 

CHECK GROUND CIRCUIT FOR IGNITION KEY HOLE ILLUMINATION

1.

Turn ignition switch OFF.

2.

Disconnect BCM connector and key hole illumination connector.

3.

Check continuity between BCM harness connector M34 terminal
1 (R/Y) and key hole illumination harness connector M40 termi-
nal 2 (R/Y). 

OK or NG

OK

>> Replace BCM. Refer to 

BCS-14, "Removal and Installa-

tion of BCM"

 .

NG

>> Repair harness or connector.

Step Lamp Does Not Illuminate

AKS00AMM

1. 

CHECK EACH DOOR SWITCH

Select “BCM” on CONSULT-II. With “INT LAMP” data monitor to
make sure switches listed below turn ON-OFF linked with switch
operation.

OK or NG

OK

>> GO TO 2.

NG

>> Inspect malfunctioning switch system.

1 (P) - Ground

: Battery voltage should exist.

PKIA6376E

41 (P) - 1 (P)

: Continuity should exist.

PKIA6378E

1 (R/Y) - 2 (R/Y)

: Continuity should exist.

PKIA6377E

Switch name

CONSULT screen

Driver side door switch

DOOR SW - DR

Passenger side door switch

DOOR SW - AS

PKIA6379E

INTERIOR ROOM LAMP

LT-191

C

D

E

F

G

H

I

J

L

M

A

B

LT

Revision: 2004 November

2004 Murano

2. 

CHECK BULB

Check bulb of lamp which does not illuminate.

OK or NG

OK

>> GO TO 3.

NG

>> Replace bulb.

3. 

CHECK STEP LAMP INPUT

1.

Turn ignition switch OFF.

2.

Disconnect step lamp (driver side/passenger side) connectors.

3.

Turn ignition switch ON.

4.

Check voltage between step lamp (driver side) harness connec-
tor D9 terminal 1 (P) and ground.

5.

Check voltage between step lamp (passenger side) harness
connector D37 terminal 1 (P) and ground.

OK or NG

OK

>> GO TO 4.

NG

>> GO TO 5.

4. 

CHECK GROUND CIRCUIT FOR STEP LAMP

1.

Turn ignition switch OFF.

2.

Disconnect BCM connector.

3.

Check continuity between BCM harness connector M35 terminal
47 (R/W) and step lamp (driver side) harness connector D9 ter-
minal 2 (R/W).  

4.

Check continuity between BCM harness connector M35 terminal
47 (R/W) and step lamp (passenger side) harness connector
D37 terminal 2 (R/W). 

OK or NG

OK

>> Replace BCM. Refer to 

BCS-14, "Removal and Installation of BCM"

 .

NG

>> Repair harness or connector.

1 (P) - Ground

: Battery voltage should exist.

1 (P) - Ground

: Battery voltage should exist.

PKIA6380E

47 (R/W) - 2 (R/W)

: Continuity should exist.

47 (R/W) - 2 (R/W)

: Continuity should exist.

PKIA6381E

LT-192

INTERIOR ROOM LAMP

Revision: 2004 November

2004 Murano

5. 

CHECK STEP LAMP CIRCUIT

1.

Disconnect BCM connector and step lamp connector.

2.

Check continuity between BCM harness connector M35 terminal
41 (P) and step lamp (driver side) harness connector D9 termi-
nal 1 (P).  

3.

Check continuity between BCM harness connector M35 terminal
41 (P) and step lamp (passenger side) harness connector D37
terminal 1 (P). 

OK or NG

OK

>> Replace BCM. Refer to 

BCS-14, "Removal and Installation of BCM"

 .

NG

>> Repair harness or connector.

All Interior Room Lamp Does Not Operate

AKS00AMN

1. 

CHECK POWER SUPPLY CIRCUIT

1.

All interior room lamps switch are OFF.

2.

Turn ignition switch ON.

3.

Check voltage between BCM harness connector M35 terminal
41 (P) and ground.

OK or NG

OK

>> Repair harness or connector. In a case of making a

short circuit, be sure to disconnect battery negative
cable after repairing harness, and then reconnect

NG

>> Replace BCM. Refer to 

BCS-14, "Removal and Installa-

tion of BCM"

 .

Bulb Replacement

AKS00AMO

ROOM LAMP

1.

Disconnect the battery negative cable.

2.

Remove the lens using clip driver or suitable tool.

3.

Remove the bulb.

4.

Install in the reverse order of removal.

MAP LAMP

Refer to 

LT-167, "Bulb Replacement"

   in “MAP LAMP”.

PERSONAL LAMP

Refer to 

LT-168, "Bulb Replacement, Removal and Installation"

   in “PERSONAL LAMP”.

STEP LAMP

Refer to 

LT-145, "Bulb Replacement"

   in “STEP LAMP”.

LUGGAGE ROOM LAMP

Refer to 

LT-169, "Bulb Replacement, Removal and Installation"

   in “LUGGAGE ROOM LAMP”.

41 (P) - 1 (P)

: Continuity should exist.

41 (P) - 1 (P)

: Continuity should exist.

PKIA6382E

Battery voltage should exist.

PKIA6383E

Room lamp

:12V - 8W

PKIA2535E

INTERIOR ROOM LAMP

LT-193

C

D

E

F

G

H

I

J

L

M

A

B

LT

Revision: 2004 November

2004 Murano

Removal and Installation

AKS00AMP

ROOM LAMP

1.

Remove the lens using clip driver or suitable tool.

2.

Using a clip driver or suitable tool and disengage the metal clip
fittings of the room lamp.

3.

Disconnect room lamp connector and remove the room lamp.

MAP LAMP

Refer to 

LT-167, "Removal and Installation"

    in “MAP LAMP”.

PERSONAL LAMP

Refer to 

LT-168, "Bulb Replacement, Removal and Installation"

   in “PERSONAL LAMP”.

STEP LAMP

Refer to 

LT-145, "Removal and Installation"

  in “STEP LAMP”.

LUGGAGE ROOM LAMP

Refer to 

LT-169, "Bulb Replacement, Removal and Installation"

   in “LUGGAGE ROOM LAMP”.

IGNITION KEY HOLE ILLUMINATION

1.

Remove the ignition key finisher. Refer to 

IP-11, "Removal and

Installation"

   in “INSTRUMENT PANEL (IP)” section.

2.

Turn the bulb socket counterclockwise and unlock it.

PKIA2539E

Ignition key hole illumination

: 12V - 0.8W

PKIA2542E

LT-194

ILLUMINATION

Revision: 2004 November

2004 Murano

ILLUMINATION

PFP:27545

System Description

AKS004MG

Control of the illumination lamps operation is dependent upon the position of the lighting switch (combination
switch). When the lighting switch is placed in the 1ST or 2ND position (or if the auto light system is activated)
the BCM (body control module) receives input signal requesting the illumination lamps to illuminate. This input
signal is communicated to the IPDM E/R (intelligent power distribution module engine room) across the CAN
communication lines. The CPU (central processing unit) of the IPDM E/R (intelligent power distribution module
engine room) controls the tail lamp relay coil. This relay, when energized, directs power to the illumination
lamps, which then illuminate. 
Power is supplied at all times

through 10A fuse [No. 71, located in IPDM E/R (intelligent power distribution module engine room)]

to tail lamp relay [located in IPDM E/R (intelligent power distribution module engine room)] and

to CPU (central processing unit) [located in IPDM E/R (intelligent power distribution module engine
room)].

through 15A fuse [No. 78, located in IPDM E/R (intelligent power distribution module engine room)]

to CPU (central processing unit) [located in IPDM E/R (intelligent power distribution module engine
room)].

Power is also supplied at all times

through 50A fusible link (letter F, located in fuse and fusible link block)

to BCM (body control module) terminal 55

through 10A fuse [No. 21, located in fuse block (J/B)]

to combination meter terminal 21.

With the ignition switch in the ON or START position, power is supplied

through 10A fuse [No. 1, located in fuse block (J/B)]

to BCM (body control module) terminal 38

through 10A fuse [No. 14, located in fuse block (J/B)]

to combination meter terminal 20.

With the ignition switch in the ACC or ON position, power is supplied

through 10A fuse [No. 6, located in fuse block (J/B)]

to BCM (body control module) terminal 11.

Ground is supplied

to BCM (body control module) terminals 49 and 52

through grounds M14 and M78

to IPDM E/R (intelligent power distribution module engine room) terminals 38 and 60 

through grounds E13, E26 and E28

to combination meter 22, 23 and 24

through grounds M14 and M78.

ILLUMINATION OPERATION BY LIGHTING SWITCH

With the lighting switch in the 1ST or 2ND position (or if the auto light system is activated), the BCM receives
input signal requesting the illumination lamps to illuminate. This input signal is communicated to the IPDM E/R
across the CAN communication lines. The CPU of the IPDM E/R controls the tail lamp relay coil, which, when
energized, directs power

through IPDM E/R terminal 22

to CVT illumination terminal 1

to VDC off switch (illumination) terminal 3 (with VDC)

to headlamp aiming switch (illumination) terminal 3 (with headlamp aiming)

to AWD lock switch (illumination) terminal 4 (AWD models)

to heated seat switch (driver side) (illumination) terminal 5 (with heater seat) 

to heated seat switch (passenger side) (illumination) terminal 5 (with heater seat)

to NAVI control unit terminal 25 (with navigation system)

ILLUMINATION

LT-195

C

D

E

F

G

H

I

J

L

M

A

B

LT

Revision: 2004 November

2004 Murano

to A/C and AV switch terminal 3

to coin box illumination terminal 1 

to glove box lamp terminal 1

to rear power window switch LH (illumination) terminal 6

to rear power window switch RH (illumination) terminal 6.

Illumination control

through combination meter terminal 15

to CVT illumination terminal 2

to VDC off switch (illumination) terminal 4 (with VDC)

to headlamp aiming switch (illumination) terminal 4 (with headlamp aiming)

to AWD lock switch (illumination) terminal 2 (AWD models)

to heated seat switch (driver side) (illumination) terminal 6 (with heater seat) 

to heated seat switch (passenger side) (illumination) terminal 6 (with heater seat)

to NAVI control unit terminal 30 (with navigation system)

to A/C and AV switch terminal 4.

Ground is supplied at all times

to coin box illumination terminal 2

to glove box lamp terminal 2

through grounds M14 and M78

to rear power window switch LH (illumination) terminal 7

through grounds B7 and B20

to rear power window switch RH (illumination) terminal 7

through grounds B105 and B116.

With power and ground supplied, illumination lamps illuminate.

EXTERIOR LAMP BATTERY SAVER CONTROL

When the combination switch (lighting switch) is in the 1ST or 2ND position (or if auto light system is acti-
vated), and the ignition switch is turned from ON or ACC to OFF, the battery saver control function is activated.
Under this condition, the illumination lamps remain illuminated for 5 minutes, then the illumination lamps are
turned off.
When the lighting switch is turned from OFF to 1ST or 2ND position (or if auto light system is activated) after
illumination lamps are turned off by the battery saver control, and illumination lamps illuminate again.
Exterior lamp battery saver control mode can be changed by the function setting of CONSULT-II.

CAN Communication System Description

AKS004MH

CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Unit

AKS007QZ

Refer to 

LAN-8, "CAN Communication Unit"

 .

LT-196

ILLUMINATION

Revision: 2004 November

2004 Murano

Schematic

AKS004MJ

TKWA1702E

ILLUMINATION

LT-197

C

D

E

F

G

H

I

J

L

M

A

B

LT

Revision: 2004 November

2004 Murano

Wiring Diagram — ILL —

AKS004MK

TKWA1703E

LT-198

ILLUMINATION

Revision: 2004 November

2004 Murano

TKWA1704E

ILLUMINATION

LT-199

C

D

E

F

G

H

I

J

L

M

A

B

LT

Revision: 2004 November

2004 Murano

TKWA0923E

LT-200

ILLUMINATION

Revision: 2004 November

2004 Murano

TKWA0924E

 

 

 

 

 

 

 

Content      ..     182      183      184      185     ..