Nissan Murano Z51 (2008 year). Manual - part 406

WT-90

< ECU DIAGNOSIS >

BCM (BODY CONTROL MODULE)

C1708: [NO DATA] FL

—

—

—

×

WT-18

C1709: [NO DATA] FR

—

—

—

×

C1710: [NO DATA] RR

—

—

—

×

C1711: [NO DATA] RL

—

—

—

×

C1712: [CHECKSUM ERR] FL

—

—

—

×

WT-21

C1713: [CHECKSUM ERR] FR

—

—

—

×

C1714: [CHECKSUM ERR] RR

—

—

—

×

C1715: [CHECKSUM ERR] RL

—

—

—

×

C1716: [PRESSDATA ERR] FL

—

—

—

×

WT-24

C1717: [PRESSDATA ERR] FR

—

—

—

×

C1718: [PRESSDATA ERR] RR

—

—

—

×

C1719: [PRESSDATA ERR] RL

—

—

—

×

C1720: [CODE ERR] FL

—

—

—

×

WT-26

C1721: [CODE ERR] FR

—

—

—

×

C1722: [CODE ERR] RR

—

—

—

×

C1723: [CODE ERR] RL

—

—

—

×

C1724: [BATT VOLT LOW] FL

—

—

—

×

WT-29

C1725: [BATT VOLT LOW] FR

—

—

—

×

C1726: [BATT VOLT LOW] RR

—

—

—

×

C1727: [BATT VOLT LOW] RL

—

—

—

×

C1729: VHCL SPEED SIG ERR

—

—

—

×

WT-32

C1734: CONTROL UNIT

—

—

—

×

WT-33

CONSULT display

Fail-safe

Freeze Frame 

Data

•Vehicle Speed

•Odo/Trip Meter

•Vehicle Condi-

tion

Intelligent Key 

warning lamp ON

Tire pressure 

monitor warning 

lamp ON

Reference 

page

Revision: 2008 October

2009 Murano

TPMS

WT-91

< SYMPTOM DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

SYMPTOM DIAGNOSIS

TPMS

Symptom Table

INFOID:0000000003375993

LOW TIRE PRESSURE WARNING LAMP SYMPTOM CHART

Diagnosis 

Item

Symptom 

(Ignition switch ON)

Low tire pressure warning lamp

Cause

Action

Low tire pres-
sure warning 
lamp

Low tire pressure 
warning lamp comes 
on immediately and 
turns off after 1 sec-
ond.

All wheel transmit-
ters are “activated” 
(working).

None (system OK)

Low tire pressure 
warning lamp blinks 
on for 2 seconds, 
then turns off for 0.2 
seconds-repeats.

All wheel transmit-
ters are not activat-
ed.

Activate all wheel tire pressure 

transmitters. Refer to 

WT-5, 

"TRANSMITTER WAKE UP 

OPERATION : Special Repair 

Requirement"

.   

Low tire pressure 
warning lamp blinks 
1 time.

Tire pressure trans-
mitter front LH is not 
activated.

Activate tire pressure transmit-

ter front LH. Refer to 

WT-5, 

"TRANSMITTER WAKE UP 

OPERATION : Special Repair 

Requirement"

.

Low tire pressure 
warning lamp blinks 
2 times.

Tire pressure trans-
mitter front RH is not 
activated.

Activate tire pressure transmit-

ter front RH. Refer to 

WT-5, 

"TRANSMITTER WAKE UP 

OPERATION : Special Repair 

Requirement"

.

Low tire pressure 
warning lamp blinks 
3 times.

Tire pressure trans-
mitter rear RH is not 
activated.

Activate tire pressure transmit-

ter rear RH. Refer to 

WT-5, 

"TRANSMITTER WAKE UP 

OPERATION : Special Repair 

Requirement"

.

SEIA0592E

SEIA0593E

SEIA0594E

SEIA0595E

SEIA0596E

Revision: 2008 October

2009 Murano

WT-92

< SYMPTOM DIAGNOSIS >

TPMS

NOTE:

If more than one wheel transmitter is NOT activated, the low tire pressure warning lamp blinking patterns for those wheels will combine.
(Example: one blink/OFF/three blinks = Tire pressure transmitter rear LH and rear RH are not activated.)

Low tire pres-
sure warning 
lamp

Low tire pressure 
warning lamp blinks 
4 times.

Tire pressure trans-
mitter rear LH is not 
activated.

Activate tire pressure transmit-

ter rear LH. Refer to 

WT-5, 

"TRANSMITTER WAKE UP 

OPERATION : Special Repair 

Requirement"

.

Low tire pressure 
warning lamp comes 
on and does not turn 
off.

Tire pressure is low.

Check tire pressure with CON-
SULT-III. Refer to 

WT-14, "AIR 

PRESSURE MONITOR : 
CONSULT-III Function (BCM - 
AIR PRESSURE MONITOR)"

.

Low tire pressure 
warning lamp blinks 
on for 0.5 seconds 
then turns off for 0.5 
seconds-repeats for 
1 minute, and then 
stays on.

The fuse for combi-
nation meter from 
battery is pulled out.

Check the fuse for combina-
tion meter from battery. Install 
or replace (if needed). 

BCM connector 
pulled out.

Check BCM connector. Re-
connect if needed.

Low tire pressure or 
tire pressure moni-
toring system mal-
function.

• Perform CONSULT-III Self-

Diagnosis. Refer to 

WT-14, 

"AIR PRESSURE MONI-
TOR : CONSULT-III Func-
tion (BCM - AIR 
PRESSURE MONITOR)"

.

- Perform ID Registration if 

needed. Refer to 

WT-5, "ID 

REGISTRATION PROCE-
DURE : Special Repair Re-
quirement"

. 

Turn signal 
lamp

Turn signal lamp 
does not blink 2 
times or buzzer does 
not sound after trans-
mitter activation.

—

1.

Tool J-45295 
[SST] does not 
activated.

2.

Ignition OFF 
during activa-
tion.

3.

Tool J-45295 
[SST] not posi-
tioned correct-
ly.

4.

Transmitters 
already activat-
ed.

1.

Install new battery.

2.

Check ignition is ON dur-
ing activation.

3.

Position tool correctly 
during activation.

4.

Nothing.

Diagnosis 

Item

Symptom 

(Ignition switch ON)

Low tire pressure warning lamp

Cause

Action

SEIA0597E

SEIA0598E

SEIA0788E

Revision: 2008 October

2009 Murano

LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN ON

WT-93

< SYMPTOM DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN ON

Description

INFOID:0000000003375994

DESCRIPTION

The low tire pressure warning lamp illuminates for approximately 1 second and then turns OFF when the igni-
tion switch is turned ON. This is to check that no abnormal condition is present in the tire pressure monitoring
system.
The lamp bulb may be burnt out or the tire pressure monitoring system may be malfunctioning if the low tire
pressure warning lamp does not illuminate when the ignition switch is turned ON. 

Diagnosis Procedure

INFOID:0000000003375995

1.

CHECK SELF-DIAGNOSIS RESULTS

With CONSULT-III

1.

On the “SELECT DIAG” mode, select the “SELF-DIAG RESULTS” screen.

2.

Check display contents in self-diagnosis results.

Is “CAN COMM CIRCUIT” displayed in the self-diagnosis display items?

YES

>> Perform trouble diagnosis for CAN communication system. Refer to 

LAN-16, "Trouble Diagnosis

Flow Chart"

.

NO

>> GO TO 2.

2.

CHECK COMBINATION METER

Check combination meter function. Refer to 

MWI-34, "CONSULT-III Function (METER/M&A)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace damaged parts.

3.

CHECK LOW TIRE PRESSURE WARNING LAMP

1.

Turn the ignition switch OFF.

2.

Disconnect BCM harness connectors.

3.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

Does low tire pressure warning lamp turn on?

YES

>> GO TO 4.

NO

>> Check combination meter and repair or replace. Refer to 

MWI-33, "Diagnosis Description"

.

4.

CHECK SYMPTOM

Check symptom again.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 5.

5.

CHECK BCM

Check BCM input/output signal. Refer to 

WT-46, "Reference Value"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 6.

6.

CHECK BCM HARNESS CONNECTOR

Check BCM pin terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-96, "Removal and Installation"

.

NO

>> Repair or replace damaged parts.

Revision: 2008 October

2009 Murano

WT-94

< SYMPTOM DIAGNOSIS >

LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN OFF

LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN OFF

Description

INFOID:0000000003375996

DESCRIPTION

The tire pressure monitoring system is checked and the warning lamp is illuminated for approximately 1 sec-
ond when the ignition switch is turned ON. The low tire pressure warning lamp turns OFF after the system
check finishes.
The system may be malfunctioning if the low tire pressure warning lamp does not turn off approximately 1 sec-
ond after the ignition switch is turned ON.

Diagnosis Procedure

INFOID:0000000003375997

1.

CHECK SYSTEM FOR BCM

With CONSULT-III

1.

On “SELF-DIAG” mode, select the “SELF-DIAG RESULTS” screen.

2.

Check display contents in self-diagnosis results.

Does self-diagnostic results indicate any malfunction?

YES

>> Perform trouble diagnosis. Refer to 

WT-14, "AIR PRESSURE MONITOR : CONSULT-III Function

(BCM - AIR PRESSURE MONITOR)"

.

NO

>> GO TO 2.

2.

CHECK ID REGISTRATION

Perform ID registration of all transmitters. Refer to 

WT-5, "ID REGISTRATION PROCEDURE : Special Repair

Requirement"

.

Does low tire pressure warning lamp turn OFF?

YES

>> INSPECTION END

NO

>> GO TO 3.

3.

CHECK BCM POWER SUPPLY CIRCUIT

1.

Turn the ignition switch OFF.

2.

Disconnect BCM harness connector.

3.

Check voltage between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>>

Check the following. If any items are damaged, repair or replace damaged parts.

• 40 A fusible link [No. L located in the fuse block]. Refer to 

PG-102, "Fuse and Fusible Link

Arrangement"

.

• 10 A fuse [No. 10 located in the fuse block (J/B)]. Refer to 

PG-101, "Fuse, Connector and Termi-

nal Arrangement"

.

• Harness for short or open between battery and BCM harness connector M118 terminal 1.
• Harness for short or open between battery and BCM harness connector M119 terminal 11.
• Check battery voltage.

4.

CHECK BCM GROUND CIRCUIT

1.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

BCM

—

Voltage (Approx.)

Connector

Terminal

M118

1

Ground

Battery voltage

M119

11

BCM

—

Continuity

Connector

Terminal

M119

13

Ground

Existed

Revision: 2008 October

2009 Murano

LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN OFF

WT-95

< SYMPTOM DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

YES

>> GO TO 5.

NO

>> Repair or replace damaged parts.

5.

CHECK SYMPTOM

Check symptom again.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 6.

6.

CHECK BCM

Check BCM input/output signal. Refer to 

WT-46, "Reference Value"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 7.

7.

CHECK BCM HARNESS CONNECTOR

Check BCM pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-96, "Removal and Installation"

.

NO

>> Repair or replace damaged parts.

Revision: 2008 October

2009 Murano

WT-96

< SYMPTOM DIAGNOSIS >

LOW TIRE PRESSURE WARNING LAMP BLINKS

LOW TIRE PRESSURE WARNING LAMP BLINKS

Description

INFOID:0000000003375998

DESCRIPTION

The low tire pressure warning lamp illuminates or blinks.
However, a check is necessary because the symptom may not be caused by a system malfunction. For exam-
ple, the transmitter may not be initialized.
NOTE:
If low tire pressure warning lamp blinks as shown in the figure, the system is normal.

Blink Mode A

• This mode shows transmitter status is in OFF- mode.

Perform transmitter wake up operation. Refer to 

WT-5, "TRANS-

MITTER WAKE UP OPERATION : Special Repair Requirement"

.

Diagnosis Procedure

INFOID:0000000003375999

1.

CHECK TIRE PRESSURE WARNING CHECK SWITCH POWER SUPPLY

1.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

2.

Check voltage between tire pressure warning check switch connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace damaged parts.

2.

CHECK TIRE PRESSURE WARNING CHECK SWITCH CIRCUIT

1.

Turn the ignition switch OFF.

2.

Disconnect BCM harness connector.

3.

Check continuity between BCM harness connector and tire pressure warning check switch connector.

4.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace damaged parts.

JPEIC0031GB

Tire pressure warning check switch

—

Voltage (Approx.)

Connector

Terminal

M19

1

Ground

11.8 V

BCM

Tire pressure warning check switch

Continuity

Connector

Terminal

Connector

Terminal

M123

149

M19

1

Existed

BCM

—

Continuity

Connector

Terminal

M123

149

Ground

Not existed

Revision: 2008 October

2009 Murano

LOW TIRE PRESSURE WARNING LAMP BLINKS

WT-97

< SYMPTOM DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

3.

CHECK BCM

Check BCM input/output signal. Refer to 

WT-46, "Reference Value"

.

Is the inspection result normal?

YES

>> Check tire pressure warning check switch. Refer to 

WT-39, "Diagnosis Procedure"

.

NO

>> Repair or replace the BCM.

Revision: 2008 October

2009 Murano

WT-98

< SYMPTOM DIAGNOSIS >

TURN SIGNAL LAMP BLINKS

TURN SIGNAL LAMP BLINKS

Description

INFOID:0000000003376000

DESCRIPTION

• The turn signal lamp blinks when the ignition switch is turned ON.
• The BCM connector or circuit may have a malfunction.

Diagnosis Procedure

INFOID:0000000003376001

1.

CHECK TIRE PRESSURE WARNING CHECK SWITCH POWER SUPPLY CIRCUIT

1.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

2.

Check voltage between tire pressure warning check switch connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace damaged parts.

2.

CHECK TIRE PRESSURE WARNING CHECK SWITCH CIRCUIT

1.

Turn the ignition switch OFF.

2.

Disconnect BCM harness connector.

3.

Check continuity between BCM harness connector and tire pressure warning check switch connector. 

4.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace damaged parts.

3.

CHECK SYMPTOM

Check again.

Does the turn signal lamp remain blinking?

YES

>> Check turn signal lamp operation. Refer to 

EXL-49, "Component Function Check"

.

NO

>> INSPECTION END

Tire pressure warning check switch

—

Voltage (Approx.)

Connector

Terminal

M19

1

Ground

11.8 V

BCM

Tire pressure warning check switch

Continuity

Connector

Terminal

Connector

Terminal

Existed

M123

149

M19

1

BCM

—

Continuity

Connector

Terminal

M123

149

Ground

Not existed

Revision: 2008 October

2009 Murano

ID REGISTRATION CANNOT BE COMPLETED

WT-99

< SYMPTOM DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

ID REGISTRATION CANNOT BE COMPLETED

Description

INFOID:0000000003376002

DESCRIPTION

The ID of the transmitter installed in each wheel cannot be registered in the tire pressure monitoring system.
Inspect the transmitter or the tire pressure monitoring system circuit.

Diagnosis Procedure

INFOID:0000000003376003

1.

CHECK ID REGISTRATION

1.

Perform ID registration of all transmitters. Refer to 

WT-5, "ID REGISTRATION PROCEDURE : Special

Repair Requirement"

.

2.

Drive at a speed of 40 km/h (25 MPH) or more for 10 minutes. 

3.

Check all tire pressures with CONSULT-III “DATA MONITOR” within 5 minutes.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK TRANSMITTER

1.

Perform trouble diagnosis for transmitters. Refer to 

WT-18, "Diagnosis Procedure"

.

2.

Perform ID registration of all transmitters. Refer to 

WT-5, "ID REGISTRATION PROCEDURE : Special

Repair Requirement"

.

Can ID registration of all transmitters be completed?

YES

>> INSPECTION END

NO

>> Replace the transmitter.

Monitored item

Condition

Display value

AIR PRESS FL

Start the engine and drive at 40 km/h (25 MPH) or more 
for 10 minutes.

Approximately equal to the indication on vehicle 
information display.

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

Revision: 2008 October

2009 Murano

WT-100

< SYMPTOM DIAGNOSIS >

NORMAL OPERATING CONDITION

NORMAL OPERATING CONDITION

Description

INFOID:0000000003376004

LOW TIRE PRESSURE WARNING LAMP BLINKS

The tire pressure monitoring system is not malfunctioning if the low
tire pressure warning lamp blinks in the pattern as shown in the fig-
ure.
The incident occurs because the transmitter of each wheel is not
wake up.
Perform transmitter wake up operation. Refer to 

WT-5, "TRANSMIT-

TER WAKE UP OPERATION : Special Repair Requirement"

.

JPEIC0031GB

Revision: 2008 October

2009 Murano

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

WT-101

< SYMPTOM DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

NVH Troubleshooting Chart

INFOID:0000000003376005

Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.

×

: Applicable

Reference page

FS

U-1

0

, 

FSU-8

.

WT

-104, "

Inspe

c

tio

n

"

WT

-105, "

Adjust

ment

"

W

T

-111

, "

T

ire Air Pressure

"

WT

-105, "

Adjust

ment

"

—

—

W

T

-111

, "

T

ire Air Pressure

"

NVH in DLN section.

NVH in DLN section.

NVH in F

AX and 

FSU 

sections.

NVH in RAX and 

RSU sections.

Re

fe

r to

 TIRES 

in

 thi

s

 ch

art.

Refe

r to

 ROAD WHEE

L i

n

 t

h

is cha

rt.

NVH in F

AX,

 RAX 

secti

on.

NVH in BR 

section.

NVH in ST section.

Possible cause and SUSPECTED PARTS

Im

p

rop

er i

n

s

ta

lla

tio

n

, 

lo

os

en

es

s

Out-of

-round

un

ba

la

nc

e

In

correct tire 

pressure

Un

ev

en

 ti

re we

ar

Def

o

rm

at

io

n

 or da

ma

ge

No

n-u

n

if

orm

ity

In

co

rrec

t ti

re 

si

ze

PR

OP

EL

LE

R

 S

H

A

F

T

DIFFERENTIAL

F

R

ONT

 AXLE AND FRONT S

U

SPENSION

REA

R

 AXLE AND REAR S

U

SPENSION

TI

RE

S

ROAD W

H

EELS

DRIV

E SHAFT

BR

AK

E

S

T

EERING

Symptom

TIRES

Noise

×

×

×

×

×

×

×

×

×

×

×

×

×

×

×

Shake

×

×

×

×

×

×

×

×

×

×

×

×

×

×

Vibration

×

×

×

×

×

×

×

Shimmy

×

×

×

×

×

×

×

×

×

×

×

×

×

Judder

×

×

×

×

×

×

×

×

×

×

×

×

Poor quality ride 
or handling

×

×

×

×

×

×

×

×

×

×

ROAD 
WHEEL

Noise

×

×

×

×

×

×

×

×

×

×

×

×

Shake

×

×

×

×

×

×

×

×

×

×

×

Shimmy, Judder

×

×

×

×

×

×

×

×

×

Poor quality ride 
or handling

×

×

×

×

×

×

×

Revision: 2008 October

2009 Murano

WT-102

< PRECAUTION >

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Service Notice or Precautions

INFOID:0000000003376006

• Low tire pressure warning lamp blinks for 1min, then turns ON when occurring any malfunction except low

tire pressure. Delete the memory with CONSULT-III, or register the ID to turn low tire pressure warning lamp
OFF. Refer to 

WT-12, "AIR PRESSURE MONITOR : Diagnosis Description"

, 

WT-5, "ID REGISTRATION

PROCEDURE : Special Repair Requirement"

.

• ID registration is required when replacing or rotating wheels, replacing transmitter or BCM. Refer to 

BCS-96,

"Exploded View"

• Replace grommet seal, valve core and cap of transmitter in TPMS every tire replacement by reaching wear

limit of tire. Refer to 

WT-108, "Exploded View"

.

Revision: 2008 October

2009 Murano

PREPARATION

WT-103

< PREPARATION >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

PREPARATION

PREPARATION

Special Service Tool

INFOID:0000000003376007

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Commercial Service Tool

INFOID:0000000003376008

Tool number 
(Kent-Moore No.)
Tool name

Description

–
(J-45295)
Transmitter activation tool

ID registration

SEIA0462E

Tool name

Description

Power tool

Loosening bolts and nuts

PBIC0190E

Revision: 2008 October

2009 Murano

WT-104

< ON-VEHICLE MAINTENANCE >

ROAD WHEEL

ON-VEHICLE MAINTENANCE

ROAD WHEEL

Inspection

INFOID:0000000003376009

ALUMINUM WHEEL

1.

Check tires for wear and improper inflation.

2.

Check wheels for deformation, cracks and other damage. If deformed, remove wheel and check wheel
runout.

a.

Remove tire from aluminum wheel and mount on a tire balance machine.

b.

Set dial indicator as shown in the figure.

c.

If the lateral deflection (A) or vertical deflection (B) for radial
runout value exceeds the limit, replace aluminum wheel.

Limit

A:

Refer to 

WT-111, "Road 

Wheel"

.

B:

Refer to 

WT-111, "Road 

Wheel"

.

SEIA0737E

Revision: 2008 October

2009 Murano

ROAD WHEEL TIRE ASSEMBLY

WT-105

< ON-VEHICLE REPAIR >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

ON-VEHICLE REPAIR

ROAD WHEEL TIRE ASSEMBLY

Adjustment

INFOID:0000000003376010

BALANCING WHEELS (BONDING WEIGHT TYPE)

Preparation Before Adjustment

Using releasing agent, remove double-faced adhesive tape from the road wheel.

CAUTION:

• Be careful not to scratch the road wheel during removal.
• After removing double-faced adhesive tape, wipe clean traces of releasing agent from the road

wheel.

Wheel Balance Adjustment

If a tire balance machine has adhesion balance weight mode settings and drive-in weight mode setting, select
and adjust a drive-in weight mode suitable for road wheels.

1.

Set road wheel on tire balance machine using the center hole as a guide. Start the tire balance machine.

2.

When inner and outer unbalance values are shown on the tire balance machine indicator, multiply outer
unbalance value by 5/3 to determine balance weight that should be used. Select the outer balance weight
with a value closest to the calculated value above and install to the designated outer position of, or at the
designated angle in relation to the road wheel.

CAUTION:

• Do not install the inner balance weight before installing the outer balance weight.
• Before installing the balance weight, be sure to clean the mating surface of the road wheel.

a.

Indicated unbalance value 

×

 5/3 = balance weight to be installed

Calculation example:
23 g (0.81 oz) 

×

 5/3 = 38.33 g (1.35 oz) 

⇒

 37.5 g (1.32 oz) bal-

ance weight (closer to calculated balance weight value)
NOTE:
Note that balance weight value must be closer to the calculated
balance weight value.
Example:
36.2 

⇒

 35 g (1.23 oz)

36.3 

⇒

 37.5 g (1.32 oz)

b.

Installed balance weight in the position.

SMA054D

Revision: 2008 October

2009 Murano