Nissan Murano Z51 (2008 year). Manual - part 401

WT-10

< FUNCTION DIAGNOSIS >

TPMS

Combination meter

Transmits the vehicle speed signal via CAN communication to BCM.

Receives the following signals via CAN communication to BCM.
• Tire pressure warning lamp signal
• Hazard lamp signal
• Buzzer signal

Low tire pressure warning lamp

Illuminates if malfunction is detected in electrical system of TPMS.

Component parts

Function

Revision: 2008 October

2009 Murano

DIAGNOSIS SYSTEM (BCM)

WT-11

< FUNCTION DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

DIAGNOSIS SYSTEM (BCM)

COMMON ITEM

COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)

INFOID:0000000003630901

APPLICATION ITEM

CONSULT-III performs the following functions via CAN communication with BCM.

SYSTEM APPLICATION

BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.

×

: Applicable item

NOTE:

• *1: At models with Intelligent Key system this item is displayed, but is not used.

• *2: At models with rain sensor this mode is displayed, but is not used.

Diagnosis mode

Function Description

Work Support

Changes the setting for each system function.

Self Diagnostic Result

Displays the diagnosis results judged by BCM.

CAN Diag Support Monitor

Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
tion manual.

Data Monitor

The BCM input/output signals are displayed.

Active Test

The signals used to activate each device are forcibly supplied from BCM.

Ecu Identification

The BCM part number is displayed.

Configuration

• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.

System

Sub system selection item

Diagnosis mode

Work Support

Data Monitor

Active Test

Door lock

DOOR LOCK

×

×

×

Rear window defogger

REAR DEFOGGER

×

×

Warning chime

BUZZER

×

×

Interior room lamp timer

INT LAMP

×

×

×

Remote keyless entry system

MULTI REMOTE ENT*

1

×

×

×

Exterior lamp

HEAD LAMP

×

×

×

Wiper and washer

WIPER

×

*

2

×

×

Turn signal and hazard warning lamps

FLASHER

×

×

×

—

AIR CONDITONER*

3

• Intelligent Key system
• Engine start system

INTELLIGENT KEY

×

×

×

Combination switch

COMB SW

×

Body control system

BCM

×

NVIS - NATS

IMMU

×

×

Interior room lamp battery saver

BATTERY SAVER

×

×

×

Back door opener system

TRUNK

×

×

Vehicle security system

THEFT ALM

×

×

×

RAP system

RETAINED PWR

×

Signal buffer system

SIGNAL BUFFER

×

×

TPMS

TPMS (AIR PRESSURE MONITOR)

×

×

×

Revision: 2008 October

2009 Murano

WT-12

< FUNCTION DIAGNOSIS >

DIAGNOSIS SYSTEM (BCM)

• *3: This item is displayed, but is not used. 

FREEZE FRAME DATA (FFD)

The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT-III.

AIR PRESSURE MONITOR

AIR PRESSURE MONITOR : Diagnosis Description

INFOID:0000000003375944

DESCRIPTION

During driving, the TPMS receives the signal transmitted from the transmitter installed in each wheel, when
the tire pressure becomes low. The control unit (BCM) of this system has pressure judgment and trouble diag-
nosis functions.
When the TPMS detects low inflation pressure or another unusual symptom, the low tire pressure warning
lamps in the combination meter comes on. 

CONSULT screen item

Indication/Unit

Description

Vehicle Speed

km/h

Vehicle speed of the moment a particular DTC is detected

Odo/Trip Meter

km

Total mileage (Odometer value) of the moment a particular DTC is detected

Vehicle Condition

SLEEP>LOCK

Power position status of 
the moment a particular 
DTC is detected

While turning BCM status from low power consumption mode to 
normal mode (Power supply position is “LOCK”)

SLEEP>OFF

While turning BCM status from low power consumption mode to 
normal mode (Power supply position is “OFF”.)

LOCK>ACC

While turning power supply position from “LOCK” to “ACC”

ACC>ON

While turning power supply position from “ACC” to “IGN”

RUN>ACC

While turning power supply position from “RUN” to “ACC” (Vehicle 
is stopping and selector lever is except P position.)

CRANK>RUN

While turning power supply position from “CRANKING” to “RUN” 
(From cranking up the engine to run it)

RUN>URGENT

While turning power supply position from “RUN“ to “ACC” (Emer-
gency stop operation)

ACC>OFF

While turning power supply position from “ACC” to “OFF”

OFF>LOCK

While turning power supply position from “OFF” to “LOCK”

OFF>ACC

While turning power supply position from “OFF” to “ACC”

ON>CRANK

While turning power supply position from “IGN” to “CRANKING”

OFF>SLEEP

While turning BCM status from normal mode (Power supply posi-
tion is “OFF”.) to low power consumption mode

LOCK>SLEEP

While turning BCM status from normal mode (Power supply posi-
tion is “LOCK”.) to low power consumption mode

LOCK

Power supply position is “LOCK” (Ignition switch OFF with steer-
ing is locked.)

OFF

Power supply position is “OFF” (Ignition switch OFF with steering 
is unlocked.)

ACC

Power supply position is “ACC” (Ignition switch ACC)

ON

Power supply position is “IGN” (Ignition switch ON with engine 
stopped)

ENGINE RUN

Power supply position is “RUN” (Ignition switch ON with engine 
running)

CRANKING

Power supply position is “CRANKING” (At engine cranking)

IGN Counter

0 - 39

The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1 

→

 2 

→

 3...38 

→

 39 after returning to the normal condition 

whenever ignition switch OFF 

→

 ON.

• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.

Revision: 2008 October

2009 Murano

DIAGNOSIS SYSTEM (BCM)

WT-13

< FUNCTION DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

SELF DIAGNOSTIC PROCEDURE (WITH CONSULT-III)

 With CONSULT-III

Touch “SELF-DIAG RESULT” display shows malfunction experienced since the last erasing operation. Refer
to 

WT-88, "DTC Index"

.

SELF DIAGNOSTIC PROCEDURE (WITHOUT CONSULT-III)

 Without CONSULT-III

To start the self-diagnostic results mode, ground terminal of the tire pressure warning check connector. The
malfunction location is indicated by the low tire pressure warning lamp blinking.

NOTE:
When the low tire pressure warning lamp blinks 5 Hz and continues repeating it, the system is normal.

JPEIC0030GB

Blinking 

pattern

Items

Diagnostic items detected when···

Check 

item

15

Tire pressure value (Front LH)

Front LH tire pressure drops to * kPa (* kg/cm

2

, * psi) or less. [NOTE]

WT-16

16

Tire pressure value (Front RH)

Front RH tire pressure drops to * kPa (* kg/cm

2

, * psi) or less. [NOTE]

17

Tire pressure value (Rear RH)

Rear RH tire pressure drops to * kPa (* kg/cm

2

, * psi) or less. [NOTE]

18

Tire pressure value (Rear LH)

Rear LH tire pressure drops to * kPa (* kg/cm

2

, * psi) or less. [NOTE]

21

Transmitter no data (Front LH)

Data from front LH transmitter can not be receive.

WT-18

22

Transmitter no data (Front RH)

Data from front RH transmitter can not be receive.

23

Transmitter no data (Rear RH)

Data from rear RH transmitter can not be receive.

24

Transmitter no data (Rear LH)

Data from rear LH transmitter can not be receive.

31

Transmitter checksum error 
(Front LH)

Checksum data from front LH transmitter is malfunctioning.

WT-21

32

Transmitter checksum error 
(Front RH)

Checksum data from front RH transmitter is malfunctioning.

33

Transmitter checksum error 
(Rear RH)

Checksum data from rear RH transmitter is malfunctioning.

34

Transmitter checksum error 
(Rear LH)

Checksum data from rear LH transmitter is malfunctioning.

35

Transmitter pressure data error 
(Front LH)

Air pressure data from front LH transmitter is malfunction.

WT-24

36

Transmitter pressure data error 
(Front RH)

Air pressure data from front RH transmitter is malfunction.

37

Transmitter pressure data error 
(Rear RH)

Air pressure data from rear RH transmitter is malfunction.

38

Transmitter pressure data error 
(Rear LH)

Air pressure data from rear LH transmitter is malfunction.

Revision: 2008 October

2009 Murano

WT-14

< FUNCTION DIAGNOSIS >

DIAGNOSIS SYSTEM (BCM)

NOTE:

182.7 kPa (1.9 kg/cm

2

, 26 psi): Standard air pressure is for 230 kPa (2.3 kg/cm

2

, 33 psi) vehicles.

ERASE SELF-DIAGNOSIS

With CONSULT-III

1.

Perform applicable inspection of malfunctioning item and then repair or replace. 

2.

Turn ignition switch ON and select “SELF-DIAG RESULTS” mode for “AIR PRESSURE MONITOR” with
CONSULT-III.

3.

Touch “ERASE” on CONSULT-III screen to erase memory.

Without CONSULT-III

• In order to make it easier to find the cause of hard-to-duplicate malfunctions, malfunction information is

stored into the control unit as necessary during use by the user. This memory is not erased no matter how
many times the ignition switch is turned ON and OFF.

• However, this information is erased by turning ignition switch OFF after performing self-diagnostic or by

erasing the memory using the CONSULT-III.

AIR PRESSURE MONITOR : CONSULT-III Function (BCM - AIR PRESSURE MONI-
TOR)

INFOID:0000000003375945

WORK SUPPORT MODE

ID Read

The registered ID number is displayed.

ID Regist

Refer to 

WT-5, "ID REGISTRATION PROCEDURE : Special Repair Requirement"

.

SELF-DIAG RESULTS MODE

Operation Procedure

Refer to 

WT-88, "DTC Index"

.

DATA MONITOR MODE

Screen of data monitor mode is displayed.
NOTE:
When malfunction is detected, CONSULT-III perform REAL-TIME DIAGNOSIS.

41

Transmitter function code error 
(Front LH)

Function code data from front LH transmitter is malfunction.

WT-26

42

Transmitter function code error 
(Front RH)

Function code data from front RH transmitter is malfunction.

43

Transmitter function code error 
(Rear RH)

Function code data from rear RH transmitter is malfunction.

44

Transmitter function code error 
(Rear LH)

Function code data from rear LH transmitter is malfunction.

45

Transmitter battery voltage low 
(Front LH)

Battery voltage of front LH transmitter drops.

WT-29

46

Transmitter battery voltage low 
(Front RH)

Battery voltage of front RH transmitter drops.

47

Transmitter battery voltage low 
(Rear RH)

Battery voltage of rear RH transmitter drops.

48

Transmitter battery voltage low 
(Rear LH)

Battery voltage of rear LH transmitter drops.

52

Vehicle speed signal error

Vehicle speed signal error.

WT-32

53

Control unit

Tire pressure monitoring system malfunction in BCM.

WT-33

No 

blinking

Tire pressure warning check 
switch

Tire pressure warning switch circuit is open.

–

Blinking 

pattern

Items

Diagnostic items detected when···

Check 

item

Revision: 2008 October

2009 Murano

DIAGNOSIS SYSTEM (BCM)

WT-15

< FUNCTION DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

Also, any malfunction detected while in this mode will be displayed at real time.

Display item list

NOTE:
Before performing the self-diagnosis, be sure to register the ID, or erase the actual malfunction location may
be different from that displayed on CONSULT-III.

ACTIVE TEST MODE

NOTE:
Before performing the self-diagnosis, be sure to register the ID, or erase the actual malfunction may be differ-
ent from that displayed on CONSULT-III.

TEST ITEM LIST

Monitor

Condition

Specification

AIR PRESS FL
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL

• Drive vehicle for a few minutes.

                           or

• Ignition switch ON and activation tool is trans-

mitting activation signals.

Tire pressure (kPa, kg/cm

2

 or Psi)

ID REGST FL
ID REGST FR
ID REGST RR
ID REGST RL

Ignition switch ON

Registration ID: Green
No registration: Red

WARNING LAMP

Low tire pressure warning lamp on: ON
Low tire pressure warning lamp off: OFF

BUZZER

Buzzer in combination meter on: ON
Buzzer in combination meter off: OFF

Test item

Content

WARNING LAMP

This test is able to check to check that the low tire pressure warning lamp turns on.

ID REGIST WARNING

This test is able to check to check that the buzzer sounds or the low tire pressure warning lamp 
turns on.

FLASHER

This test is able to check to check that each turn signal lamp turns on.

HORN

This test is able to check to check that the horn sounds.

Revision: 2008 October

2009 Murano

WT-16

< COMPONENT DIAGNOSIS >

C1704, C1705, C1706, C1707 LOW TIRE PRESSURE

COMPONENT DIAGNOSIS

C1704, C1705, C1706, C1707 LOW TIRE PRESSURE

Description

INFOID:0000000003375946

When the tire pressure monitoring system detects low inflation pres-
sure, the low tire pressure warning lamps in the combination meter
comes on.

DTC Logic

INFOID:0000000003375947

DTC DETECTION LOGIC

NOTE: 182.7 kPa (1.9 kg/cm

2

, 26 psi): Standard air pressure is for 230 kPa (2.3 kg/cm

2

, 33 psi) vehicles.

DTC CONFIRMATION PROCEDURE

1.

DTC REPRODUCTION PROCEDURE 

With CONSULT-III

1.

Drive at a speed of 40 km/h (25 MPH) or more for 10 minutes.

2.

Perform BCM self-diagnosis.

Is DTC “C1704”, “C1705”, “C1706”, “C1707” detected?

YES

>> Proceed to diagnosis procedure. Refer to 

WT-16, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003375948

1.

CHECK TIRE AIR PRESSURE

1.

Check all tire air pressures.

2.

Adjust all tire air pressures. Refer to 

WT-111, "Tire Air Pressure"

Does all tire pressure data meet the specification?

YES

>> GO TO 2.

NO

>> Inspect or replace malfunction parts.

2.

CHECK AIR PRESSURE SIGNAL

1.

Drive at a speed of 40 km/h (25 MPH) or more for 10 minutes.

2.

Check all tire pressure with CONSULT-III “DATA MONITOR” within 5 minutes.

SEIA0434E

DTC

Display item

Malfunction detected condition

Possible cause

C1704

LOW PRESSURE FL

Front LH tire pressure drops to * kPa (* kg/cm

2

, * psi) or less. [NOTE]

Tire pressure is low

C1705

LOW PRESSURE FR

Front RH tire pressure drops to * kPa (* kg/cm

2

, * psi) or less. [NOTE]

C1706

LOW PRESSURE RR

Rear RH tire pressure drops to * kPa (* kg/cm

2

, * psi) or less. [NOTE]

C1707

LOW PRESSURE RL

Rear LH tire pressure drops to * kPa (* kg/cm

2

, * psi) or less. [NOTE]

Revision: 2008 October

2009 Murano

C1704, C1705, C1706, C1707 LOW TIRE PRESSURE

WT-17

< COMPONENT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

Is inspection result normal?

YES

>> INSPECTION END

NO

>> Repair or replace damaged parts (tire or wheel). Refer to 

WT-102, "Service Notice or Precau-

tions"

.

Special Repair Requirement

INFOID:0000000003523560

1.

CHECK TIRE AIR PRESSURE

Check all tire air pressures. Refer to 

WT-111, "Tire Air Pressure"

.

Does all tire pressure data meet the specification?

YES

>> GO TO 2.

NO

>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.

2.

PERFORM ID REGISTRATION

Perform ID registration. Refer to 

WT-5, "ID REGISTRATION PROCEDURE : Special Repair Requirement"

.

>> END

Monitored item

Condition

Display value

AIR PRESS FL

Start the engine and drive at a 40 km/h (25 MPH) or 
more for 10 minutes.

Approximately equal to the indication on vehicle 
information display.

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

Revision: 2008 October

2009 Murano

WT-18

< COMPONENT DIAGNOSIS >

C1708, C1709, C1710, C1711 TRANSMITTER

C1708, C1709, C1710, C1711 TRANSMITTER

Description

INFOID:0000000003375949

The transmitter (1) integrated with a valve is installed on a wheel (2),
and transmits a detected air pressure signal by radio wave. 

DTC Logic

INFOID:0000000003375950

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

DTC REPRODUCTION PROCEDURE

With CONSULT-III

1.

Drive at a speed of 40 km/h (25 MPH) or more for 10 minutes.

2.

Perform BCM self-diagnosis.

Is DTC “C1708”, “C1709”, “C1710”, “C1711” detected?

YES

>> Proceed to diagnosis procedure. Refer to 

WT-18, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003375951

1.

CHECK AIR PRESSURE SIGNAL

With CONSULT-III

1.

Start the engine.

2.

Select “DATA MONITOR” mode for “AIR PRESSURE MONITOR” with CONSULT-III.

3.

Read out the value of “AIR PRESS FL”, “AIR PRESS FR”, “AIR PRESS RR”, “AIR PRESS RL”.

Are all tire pressures displayed 0 kPa?

YES

>> GO TO 2.

NO

>> GO TO 4.

2.

CHECK HARNESS BETWEEN BCM AND TIRE PRESSURE RECEIVER

1.

Turn the ignition switch OFF.

2.

Disconnect BCM harness connector and tire pressure receiver harness connector.

: Outside

SEIA0768E

DTC

Display item

Malfunction detected condition

Possible cause

C1708

[NO DATA] FL

Data from front LH transmitter can not receive.

• Harness or connector

(Tire pressure receiver, BCM)

• ID registration is not finished
• Transmitter malfunction
• BCM malfunction

C1709

[NO DATA] FR

Data from front RH transmitter can not receive.

C1710

[NO DATA] RR

Data from rear RH transmitter can not receive.

C1711

[NO DATA] RL

Data from rear LH transmitter can not receive.

Monitored item

Condition

Display value

AIR PRESS FL

Start the engine and drive at a 40 km/h (25 MPH) or more for 
10 minutes.

Approximately equal to the indication on 
vehicle information display.

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

Revision: 2008 October

2009 Murano

C1708, C1709, C1710, C1711 TRANSMITTER

WT-19

< COMPONENT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

3.

Check continuity between BCM harness connector and tire pressure receiver harness connector.

4.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace damaged parts.

3.

CHECK TIRE PRESSURE RECEIVER

Check tire pressure receiver. Refer to 

WT-36, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> Check BCM pin terminals for damage or loose connection with harness connector. If any items

are damaged, repair or replace damaged parts.

NO

>> Replace the tire pressure receiver.

4.

CHECK ID REGISTRATION

Perform ID registration of all transmitters. Refer to 

WT-5, "ID REGISTRATION PROCEDURE : Special Repair

Requirement"

.

Can ID registration of all transmitters be completed?

YES

>> GO TO 5.

NO

>> Replace malfunctioning transmitter.

5.

CHECK TIRE PRESSURE MONITORING SYSTEM

With CONSULT-III

1.

Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.

2.

Check all tire pressures with CONSULT-III “DATA MONITOR” within 15 minutes after stopped vehicle.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace BCM.

Special Repair Requirement

INFOID:0000000003375952

1.

CHECK TIRE AIR PRESSURE

Check all tire air pressures. Refer to 

WT-111, "Tire Air Pressure"

.

Does all tire pressure data meet the specification?

YES

>> GO TO 2.

BCM

Tire pressure receiver

Continuity

Connector

Terminal

Connector

Terminal

M123

137

M21

1

Existed

138

4

139

2

BCM

—

Continuity

Connector

Terminal

M123

137

Ground

Not existed

138

139

Monitored item

Condition

Display value

AIR PRESS FL

Start the engine and drive at a 40 km/h (25MPH) or 
more several minutes.

Approximately equal to the indication on vehicle 
information display.

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

Revision: 2008 October

2009 Murano

WT-20

< COMPONENT DIAGNOSIS >

C1708, C1709, C1710, C1711 TRANSMITTER

NO

>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.

2.

PERFORM ID REGISTRATION

Perform ID registration. Refer to 

WT-5, "ID REGISTRATION PROCEDURE : Special Repair Requirement"

.

>> END

Revision: 2008 October

2009 Murano

C1712, C1713, C1714, C1715 TRANSMITTER

WT-21

< COMPONENT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

C1712, C1713, C1714, C1715 TRANSMITTER

Description

INFOID:0000000003412912

The transmitter (1) integrated with a valve is installed on a wheel (2),
and transmits a detected air pressure signal by radio wave. 

DTC Logic

INFOID:0000000003375954

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

DTC REPRODUCTION PROCEDURE

With CONSULT-III

1.

Drive at a speed of 40 km/h (25 MPH) or more for 10 minutes.

2.

Perform BCM self-diagnosis.

Is DTC “C1712”, “C1713”, “C1714“, ”C1715” detected?

YES

>> Proceed to diagnosis procedure. Refer to 

WT-21, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003375955

1.

CHECK ID REGISTRATION

With CONSULT-III

1.

Perform the ID registration of all transmitters. Refer to 

WT-5, "ID REGISTRATION PROCEDURE : Special

Repair Requirement"

.

2.

Drive at a speed of 40 km/h (25 MPH) or more for 10 minutes.

3.

Check all tire pressure with CONSULT-III “DATA MONITOR” within 5 minutes.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> GO TO 2.

2.

CHECK AIR PRESSURE SIGNAL

: Outside

SEIA0768E

DTC

Display item

Malfunction detected condition

Possible case

C1712

[CHECKSUM ERR] FL

Checksum data from front LH transmitter is malfunction.

• Tire pressure receiver malfunc-

tion

• Transmitter malfunction
• BCM malfunction
• Harness or connector

C1713

[CHECKSUM ERR] FR

Checksum data from front RH transmitter is malfunction.

C1714

[CHECKSUM ERR] RR

Checksum data from rear RH transmitter is malfunction.

C1715

[CHECKSUM ERR] RL

Checksum data from rear LH transmitter is malfunction.

Monitored item

Condition

Display value

AIR PRESS FL

Start the engine and drive at a 40 km/h (25 MPH) or 
more for 10 minutes.

Approximately equal to the indication on vehicle 
information display.

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

Revision: 2008 October

2009 Murano

WT-22

< COMPONENT DIAGNOSIS >

C1712, C1713, C1714, C1715 TRANSMITTER

 With CONSULT-III

1.

Start the engine.

2.

Select “DATA MONITOR” mode for “AIR PRESSURE MONITOR” with CONSULT-III.

3.

Read out the value of “AIR PRESS FL”, “AIR PRESS FR”, “AIR PRESS RR” and “AIR PRESS RL”.

Are all tire pressures displayed 0 kPa?

YES

>> GO TO 3.

NO

>> GO TO 5.

3.

CHECK HARNESS BETWEEN BCM AND TIRE PRESSURE RECEIVER

1.

Turn the ignition switch OFF.

2.

Disconnect BCM harness connector and tire pressure receiver harness connector.

3.

Check continuity between BCM harness connector and tire pressure receiver harness connector.

4.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace damaged parts.

4.

CHECK TIRE PRESSURE RECEIVER

Check tire pressure receiver. Refer to 

WT-36, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> Check BCM pin terminals for damage or loose connection with harness connector. If any items

are damaged, repair or replace damaged parts.

NO

>> Replace the tire pressure receiver.

5.

CHECK ID REGISTRATION

Perform ID registration of all transmitters. Refer to 

WT-5, "ID REGISTRATION PROCEDURE : Special Repair

Requirement"

.

Can ID registration of all transmitters be completed?

YES

>> GO TO 6.

NO

>> Replace malfunctioning transmitter.

6.

CHECK TIRE PRESSURE MONITORING SYSTEM

With CONSULT-III

1.

Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.

2.

Check all tire pressure with CONSULT-III “DATA MONITOR” within 15 minutes after stopped vehicle. 

Monitored item

Condition

Display value

AIR PRESS FL

Start the engine and drive at 40 km/h (25 MPH) or more 
for 10 minutes.

Approximately equal to the indication on vehicle 
information display.

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

BCM

Tire pressure receiver

Continuity

Connector

Terminal

Connector

Terminal

M123

137

M21

1

Existed

138

4

139

2

BCM

—

Continuity

Connector

Terminal

M123

137

Ground

Not existed

138

139

Revision: 2008 October

2009 Murano

C1712, C1713, C1714, C1715 TRANSMITTER

WT-23

< COMPONENT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

Is the inspection result normal? 

YES

>> INSPECTION END

NO

>> Replace BCM. Refer to 

BCS-96, "Removal and Installation"

.

Special Repair Requirement

INFOID:0000000003375956

1.

CHECK TIRE AIR PRESSURE

Check all tire air pressures. Refer to 

WT-111, "Tire Air Pressure"

.

Does all tire pressure data meet the specification?

YES

>> GO TO 2.

NO

>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.

2.

PERFORM ID REGISTRATION

Perform ID registration. Refer to 

WT-5, "ID REGISTRATION PROCEDURE : Special Repair Requirement"

.

>> END

Monitored item

Condition

Display value

AIR PRESS FL

Start the engine and drive at 40 km/h (25 MPH) or more 
for several minutes.

Approximately equal to the indication on vehicle 
information display.

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

Revision: 2008 October

2009 Murano

WT-24

< COMPONENT DIAGNOSIS >

C1716, C1717, C1718, C1719 TRANSMITTER

C1716, C1717, C1718, C1719 TRANSMITTER

Description

INFOID:0000000003412913

The transmitter (1) integrated with a valve is installed on a wheel (2),
and transmits a detected air pressure signal by radio wave. 

DTC Logic

INFOID:0000000003375958

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

DTC REPRODUCTION PROCEDURE

With CONSULT-III

1.

Drive at a speed of 40 km/h (25 MPH) or more for 10 minutes.

2.

Perform BCM self-diagnosis.

Is DTC “C1716”, “C1717”, “C1718”, “C1719” detected?

YES

>> Proceed to diagnosis procedure. Refer to 

WT-24, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003375959

1.

CHECK TIRE PRESSURE

With CONSULT-III

1.

Adjust tire pressure to specified value. Refer to 

WT-111, "Tire Air Pressure"

.

2.

Perform the ID registration of all transmitters. Refer to 

WT-5, "ID REGISTRATION PROCEDURE : Special

Repair Requirement"

.

3.

Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.

4.

Check all tire pressure with CONSULT-III “DATA MONITOR” within 15 minutes after stopped vehicle.

Is tire pressure indicated as 438.60 kPa (4.47kg/cm

2

, 63.60 psi) on the “DATA MONITOR” screen?

YES

>> Replace malfunctioning transmitter.

NO

>> GO TO 2.

2.

CHECK TIRE PRESSURE MONITORING SYSTEM

: Outside

SEIA0768E

DTC

Display item

Malfunction detected condition

Possible case

C1716

[PRESSDATA ERR] FL

Air pressure data from front LH transmitter malfunction.

• ID registration is not fin-

ished

• Transmitter malfunction

C1717

[PRESSDATA ERR] FR

Air pressure data from front RH transmitter malfunction.

C1718

[PRESSDATA ERR] RR

Air pressure data from rear RH transmitter malfunction.

C1719

[PRESSDATA ERR] RL

Air pressure data from rear LH transmitter malfunction.

Monitored item

Condition

Display value

AIR PRESS FL

Start the engine and drive at 40 km/h (25 MPH) or 
more for several minutes.

Approximately equal to the indication on vehicle 
information display.

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

Revision: 2008 October

2009 Murano

C1716, C1717, C1718, C1719 TRANSMITTER

WT-25

< COMPONENT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

With CONSULT-III

1.

Perform the ID registration of all transmitters. Refer to 

WT-5, "ID REGISTRATION PROCEDURE : Special

Repair Requirement"

.

2.

Drive at a speed of 40 km/h (25 MPH) or more for 10 minutes.

3.

Check all tire pressures with CONSULT-III “DATA MONITOR” within 5 minutes.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Perform the self-diagnosis, inspect detected malfunction. Refer to 

WT-12, "AIR PRESSURE

MONITOR : Diagnosis Description"

.

Component Inspection

INFOID:0000000003375960

1.

CHECK TRANSMITTER

With CONSULT-III

1.

Adjust tire pressure to specified value. Refer to 

WT-111, "Tire Air Pressure"

.

2.

Perform ID registration of all transmitters. Refer to 

WT-5, "ID REGISTRATION PROCEDURE : Special

Repair Requirement"

.

3.

Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.

4.

Check all tire pressure with CONSULT-III “DATA MONITOR” within 15 minutes after stopped vehicle.

Is tire pressure indicated as 438.60 kPa (4.47 kg/cm

2

, 63.60 psi) on the “DATA MONITOR” screen?

YES

>> Replace malfunctioning transmitter.

NO

>> INSPECTION END

Special Repair Requirement

INFOID:0000000003375961

1.

CHECK TIRE AIR PRESSURE

Check all tire air pressures. Refer to 

WT-111, "Tire Air Pressure"

.

Does all tire pressure data meet the specification?

YES

>> GO TO 2.

NO

>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.

2.

PERFORM ID REGISTRATION

Perform ID registration. Refer to 

WT-5, "ID REGISTRATION PROCEDURE : Special Repair Requirement"

.

>> END

Monitored item

Condition

Display value

AIR PRESS FL

Start the engine and drive at 40 km/h (25 MPH) or 
more for 10 minutes.

Approximately equal to the indication on vehicle 
information display.

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

Monitored item

Condition

 Display value

AIR PRESSURE FL

Start the engine and drive at s 40 km/h (25 MPH) or 
more several minutes.

Approximately equal to the indication on vehicle in-
formation display.

AIR PRESSURE FR

AIR PRESSURE RR

AIR PRESSURE RL

Revision: 2008 October

2009 Murano