Nissan Murano Z51 (2008 year). Manual

SRC-240

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

B1113, B1114 SATELLITE SENS RH

CHECK AIR BAG WARNING LAMP

Check the air bag warning lamp status.
Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-305

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000003367658

With CONSULT-lll

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DIAGNOSTIC PROCEDURE

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace wiring harness.

CHECK SATELLITE SENSOR

Replace RH satellite sensor.

Check the screen of CONSULT-lll.

Is the inspection result normal?

YES

>> INSPECTION END.

>> Check the intermittent incident. Refer to

GI-40, "Intermittent Incident"

Revision: 2008 October

2009 Murano

B1115, B1116 SATELLITE SENS RH

SRC-241

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

SRC

B1115, B1116 SATELLITE SENS RH

Description

INFOID:0000000003367659

DTC B1115, B1116 [COMM FAIL] SATELLITE SENS RH

Main “G” sensor generates signal voltage, when it detects deceleration beyond the specified level by vehicle
side collision.

OPERATION

When ACU defines both signal voltage of the “G” sensor and the Safing algorithm to be that of collision which
exceeds specified level, the driving circuit switches on and feeds the electric ignitor of both the front side air
bag and side curtain air bag.

STRUCTURE

Integrated type of the G sensor element for side collision with output terminals for signal voltage.

INSTALLATION

RH satellite sensor is installed at the underside of center pillar with fixed nuts.

DTC Logic

INFOID:0000000003367660

DTC DETECTION LOGIC

With CONSULT-lll

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-lll.

Is malfunctioning part detected?

YES

>> Refer to

SRC-242, "Diagnosis Procedure"

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1115
B1116

SATELLITE SENS RH
[COMM FAIL]
[UNMATCH]

RH satellite sensor is out of order

• Disconnection of wiring harness
• Internal breakdown in RH satellite

sensor

• Internal breakdown in air bag diag-

nosis sensor unit

Revision: 2008 October

2009 Murano

SRC-242

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

B1115, B1116 SATELLITE SENS RH

CHECK AIR BAG WARNING LAMP

Check the air bag warning lamp status.
Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-305

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000003367661

With CONSULT-lll

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DIAGNOSTIC PROCEDURE

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace wiring harness.

CHECK SATELLITE SENSOR

Replace RH satellite sensor.

Check the screen of CONSULT-lll.

Is the inspection result normal?

YES

>> INSPECTION END.

>> Check the intermittent incident. Refer to

GI-40, "Intermittent Incident"

Revision: 2008 October

2009 Murano

B1118, B1119 SATELLITE SENS LH

SRC-243

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

SRC

B1118, B1119 SATELLITE SENS LH

Description

INFOID:0000000003367662

DTC B1118, B1119 [UNIT FAIL] SATELLITE SENS LH

Main “G” sensor generates signal voltage, when it detects deceleration beyond the specified level by vehicle
side collision.

OPERATION

STRUCTURE

Integrated type of the G sensor element for side collision with output terminals for signal voltage.

INSTALLATION

LH satellite sensor is installed at the underside of center pillar with fixed nuts.

DTC Logic

INFOID:0000000003367663

DTC DETECTION LOGIC

With CONSULT-lll

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-lll.

Is malfunctioning part detected?

YES

>> Refer to

SRC-244, "Diagnosis Procedure"

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1118
B1119

SATELLITE SENS LH
[UNIT FAIL]

LH satellite sensor is out of order

• Disconnection of wiring harness
• Internal breakdown in LH satellite

sensor

• Internal breakdown in air bag diag-

nosis sensor unit

Revision: 2008 October

2009 Murano

SRC-244

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

B1118, B1119 SATELLITE SENS LH

CHECK AIR BAG WARNING LAMP

Check the air bag warning lamp status.
Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-305

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000003367664

With CONSULT-lll

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DIAGNOSTIC PROCEDURE

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace wiring harness.

CHECK SATELLITE SENSOR

Replace LH satellite sensor.

Check the screen of CONSULT-lll.

Is the inspection result normal?

YES

>> INSPECTION END.

>> Check the intermittent incident. Refer to

GI-40, "Intermittent Incident"

Revision: 2008 October

2009 Murano

B1120, B1121 SATELLITE SENS LH

SRC-245

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

SRC

B1120, B1121 SATELLITE SENS LH

Description

INFOID:0000000003367665

DTC B1120, B1121 [COMM FAIL] SATELLITE SENS LH

Main “G” sensor generates signal voltage, when it detects deceleration beyond the specified level by vehicle
side collision.

OPERATION

STRUCTURE

Integrated type of the G sensor element for side collision with output terminals for signal voltage.

INSTALLATION

LH satellite sensor is installed at the underside of center pillar with fixed nuts.

DTC Logic

INFOID:0000000003367666

DTC DETECTION LOGIC

With CONSULT-lll

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-lll.

Is malfunctioning part detected?

YES

>> Refer to

SRC-246, "Diagnosis Procedure"

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1120

B1121

SATELLITE SENS LH
[COMM FAIL]
[UNMATCH]

LH satellite sensor is out of order

• Disconnection of wiring harness
• Internal breakdown in LH satellite

sensor

• Internal breakdown in air bag diag-

nosis sensor unit

Revision: 2008 October

2009 Murano

SRC-246

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

B1120, B1121 SATELLITE SENS LH

CHECK AIR BAG WARNING LAMP

Check the air bag warning lamp status.
Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-305

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000003367667

With CONSULT-lll

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DIAGNOSTIC PROCEDURE

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace wiring harness.

CHECK SATELLITE SENSOR

Replace LH satellite sensor.

Check the screen of CONSULT-lll.

Is the inspection result normal?

YES

>> INSPECTION END.

>> Check the intermittent incident. Refer to

GI-40, "Intermittent Incident"

Revision: 2008 October

2009 Murano

B1122, B1123, B1124, B1125, B1126, B1127 DIAGNOSIS SENSOR UNIT

SRC-247

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

SRC

B1122, B1123, B1124, B1125, B1126, B1127 DIAGNOSIS SENSOR UNIT

Description

INFOID:0000000003367668

DTC B1122, B1123, B1124, B1125, B1126, B1127 DIAGNOSIS SENSOR UNIT

Detects the whole SRS electrical system and displays the malfunction either by illuminating or blinking the air
bag warning lamp in the combination meter. Malfunctioning part can be detected by on board self-diagnosis
system and electro-diagnosis tester CONSULT-III.

OPERATION

It detects a shock that exceeds specified level and monitors such systems as the driver and passenger air
bag, front side air bag, side curtain air bag, pre-tensioner seat belts operate properly.

STRUCTURE

It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.

INSTALLATION

Air bag diagnosis sensor unit is installed under the center console with fixed bolts.

DTC Logic

INFOID:0000000003367669

DTC DETECTION LOGIC

With CONSULT-III

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-III)

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-III.

Is malfunctioning part detected?

YES

>> Refer to

SRC-248, "Diagnosis Procedure"

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-III)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

INSPECTION START

Turn ignition switch ON.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1122
B1123
B1124
B1125
B1126
B1127

CONTROL UNIT

Air bag diagnosis sensor unit is out of
order or mis-match

• Internal breakdown in air bag diag-

nosis sensor unit

• Mis-match between specification on

vehicle and configuration in air bag
diagnosis sensor unit

Revision: 2008 October

2009 Murano

SRC-248

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

B1122, B1123, B1124, B1125, B1126, B1127 DIAGNOSIS SENSOR UNIT

>> GO TO 2.

CHECK AIR BAG WARNING LAMP

Check the air bag warning lamp status.

Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-305

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000003367670

With CONSULT-III

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DIAGNOSTIC PROCEDURE

CHECK HARNESS CONNECTOR

Check the connection of harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness connectors.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace wiring harness.

CHECK AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit.

Check the screen of CONSULT-III.

Is the inspection result normal?

YES

>> INSPECTION END.

>> Check the intermittent incident. Refer to

GI-40, "Intermittent Incident"

Revision: 2008 October

2009 Murano

B1129 SIDE MODULE RH

SRC-249

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

SRC

B1129 SIDE MODULE RH

Description

INFOID:0000000003367671

DTC B1129 [OPEN] SIDE MODULE RH

For front RH side air bag module, crash is judged by main “G” sensor output signal (left side:LH satellite sen-
sor, right side:RH satellite sensor) and Safing algorithm (in air bag diagnosis sensor unit).

OPERATION

In the case of a collision whose acceleration exceeds the specified level, the ignition materials are ignited by
electric ignition system. The system burns and introduces the chemical reaction of gas generating materials to
generate hot gases that flow into the air bag through a filter and expand the bag.

STRUCTURE

Front RH side air bag module mainly consists of air bag and inflator which inflates air bag.

INSTALLATION

Front RH side air bag module is installed on the side of front seat back with fixed nuts.

DTC Logic

INFOID:0000000003367672

DTC DETECTION LOGIC

With CONSULT-lll

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-lll.

Is malfunctioning part detected?

YES

>> Refer to

SRC-250, "Diagnosis Procedure"

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1129

SIDE MODULE RH
[OPEN]

Front RH side air bag module circuit is
open

• Disconnection of wiring harness and

open

• Internal breakdown in front RH side

air bag module

• Internal breakdown in air bag diag-

nosis sensor unit

Revision: 2008 October

2009 Murano

SRC-250

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

B1129 SIDE MODULE RH

CHECK AIR BAG WARNING LAMP

Check the air bag warning lamp status.
Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-305

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000003367673

With CONSULT-lll

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DIAGNOSTIC PROCEDURE

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace wiring harness.

CHECK FRONT SIDE AIR BAG MODULE

Replace front RH side air bag module.

Check the screen of CONSULT-lll.

Is the inspection result normal?

YES

>> INSPECTION END.

>> Check the intermittent incident. Refer to

GI-40, "Intermittent Incident"

Revision: 2008 October

2009 Murano

B1130 SIDE MODULE RH

SRC-251

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

SRC

B1130 SIDE MODULE RH

Description

INFOID:0000000003367674

DTC B1130 [VB-SHORT] SIDE MODULE RH

For front RH side air bag module, crash is judged by main “G” sensor output signal (left side: LH satellite sen-
sor, right side: RH satellite sensor) and Safing algorithm (in air bag diagnosis sensor unit).

OPERATION

STRUCTURE

Front RH side air bag module mainly consists of air bag and inflator which inflates air bag.

INSTALLATION

Front RH side air bag module is installed on the side of front seatback with fixed nuts.

DTC Logic

INFOID:0000000003367675

DTC DETECTION LOGIC

With CONSULT-lll

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-lll.

Is malfunctioning part detected?

YES

>> Refer to

SRC-252, "Diagnosis Procedure"

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1130

SIDE MODULE RH
[VB-SHORT]

Front RH side air bag module circuit is
shorted to some power supply circuit

• Disconnection of wiring harness and

short

• Internal breakdown in front RH side

air bag module

• Internal breakdown in air bag diag-

nosis sensor unit

Revision: 2008 October

2009 Murano

SRC-252

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

B1130 SIDE MODULE RH

CHECK AIR BAG WARNING LAMP

Check the air bag warning lamp status.
Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-305

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000003367676

With CONSULT-lll

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DIAGNOSTIC PROCEDURE

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace wiring harness.

CHECK FRONT SIDE AIR BAG MODULE

Replace front RH side air bag module.

Check the screen of CONSULT-lll.

Is the inspection result normal?

YES

>> INSPECTION END.

>> Check the intermittent incident. Refer to

GI-40, "Intermittent Incident"

Revision: 2008 October

2009 Murano

B1131 SIDE MODULE RH

SRC-253

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

SRC

B1131 SIDE MODULE RH

Description

INFOID:0000000003367677

DTC B1131 [GND-SHORT] SIDE MODULE RH

OPERATION

STRUCTURE

Front RH side air bag module mainly consists of air bag and inflator which inflates air bag.

INSTALLATION

Front RH side air bag module is installed on the side of front seatback with fixed nuts.

DTC Logic

INFOID:0000000003367678

DTC DETECTION LOGIC

With CONSULT-lll

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-lll.

Is malfunctioning part detected?

YES

>> Refer to

SRC-254, "Diagnosis Procedure"

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1131

SIDE MODULE RH
[GND-SHORT]

Front RH side air bag module circuit is
shorted to ground

• Disconnection of wiring harness and

short

• Internal breakdown in front RH side

air bag module

• Internal breakdown in air bag diag-

nosis sensor unit

Revision: 2008 October

2009 Murano

SRC-254

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

B1131 SIDE MODULE RH

CHECK AIR BAG WARNING LAMP

Check the air bag warning lamp status.
Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-305

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000003367679

With CONSULT-lll

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DIAGNOSTIC PROCEDURE

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace wiring harness.

CHECK FRONT SIDE AIR BAG MODULE

Replace front RH side air bag module.

Check the screen of CONSULT-lll.

Is the inspection result normal?

YES

>> INSPECTION END.

>> Check the intermittent incident. Refer to

GI-40, "Intermittent Incident"

Revision: 2008 October

2009 Murano

B1132 SIDE MODULE RH

SRC-255

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

SRC

B1132 SIDE MODULE RH

Description

INFOID:0000000003367680

DTC B1132 [SHORT] SIDE MODULE RH

OPERATION

STRUCTURE

Front RH side air bag module mainly consists of air bag and inflator which inflates air bag.

INSTALLATION

Front RH side air bag module is installed on the side of front seatback with fixed nuts.

DTC Logic

INFOID:0000000003367681

DTC DETECTION LOGIC

With CONSULT-lll

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-lll.

Is malfunctioning part detected?

YES

>> Refer to

SRC-256, "Diagnosis Procedure"

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1132

SIDE MODULE RH
[SHORT]

Front RH side air bag module circuit are
shorted to each other

• Disconnection of wiring harness and

short

• Internal breakdown in front RH side

air bag module

• Internal breakdown in air bag diag-

nosis sensor unit

Revision: 2008 October

2009 Murano

Nissan Murano Z51 (2008 year). Manual - part 364