Nissan Murano Z51 (2008 year). Manual

SRC-208

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

B1065, B1070 ASSIST A/B MODULE

CHECK AIR BAG WARNING LAMP

Check the air bag warning lamp status.
Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-305

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000003367616

With CONSULT-lll

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DIAGNOSTIC PROCEDURE

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace wiring harness.

CHECK FRONT PASSENGER AIR BAG MODULE

Replace front passenger air bag module.

Check the screen of CONSULT-lll.

Is the inspection result normal?

YES

>> INSPECTION END.

>> Check the intermittent incident. Refer to

GI-40, "Intermittent Incident"

Revision: 2008 October

2009 Murano

B1066, B1071 ASSIST A/B MODULE

SRC-209

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

SRC

B1066, B1071 ASSIST A/B MODULE

Description

INFOID:0000000003367617

DTC B1066, B1071 [VB-SHORT] ASSIST A/B MODULE

For front passenger air bag module, crash is judged by main “G” sensor output signal and Safing algorithm in
front direction.

OPERATION

In the case of a frontal collision whose acceleration exceeds the specified level, the ignition materials are
ignited by electric ignition system. The system burns and introduces the chemical reaction of gas generating
materials to generate hot gases that flow into the air bag through a filter and expand the bag.

STRUCTURE

Front passenger air bag module mainly consists of air bag and inflator which inflates air bag.

INSTALLATION

Front passenger air bag module is installed on the instrument panel with fixed bolts.

DTC Logic

INFOID:0000000003367618

DTC DETECTION LOGIC

With CONSULT-lll

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-lll.

Is malfunctioning part detected?

YES

>> Refer to

SRC-210, "Diagnosis Procedure"

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1066
B1071

ASSIST A/B MODULE
[VB-SHORT]

Front passenger air bag module circuit
is shorted to some power supply circuit

• Disconnection of wiring harness and

short

• Internal breakdown in front passen-

ger air bag module

• Internal breakdown in air bag diag-

nosis sensor unit

Revision: 2008 October

2009 Murano

SRC-210

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

B1066, B1071 ASSIST A/B MODULE

CHECK AIR BAG WARNING LAMP

Check the air bag warning lamp status.
Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-305

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000003367619

With CONSULT-lll

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DIAGNOSTIC PROCEDURE

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace wiring harness.

CHECK FRONT PASSENGER AIR BAG MODULE

Replace front passenger air bag module.

Check the screen of CONSULT-lll.

Is the inspection result normal?

YES

>> INSPECTION END.

>> Check the intermittent incident. Refer to

GI-40, "Intermittent Incident"

Revision: 2008 October

2009 Murano

B1067, B1072 ASSIST A/B MODULE

SRC-211

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

SRC

B1067, B1072 ASSIST A/B MODULE

Description

INFOID:0000000003367620

DTC B1067, B1072 [GND-SHORT] ASSIST A/B MODULE

For front passenger air bag module, crash is judged by main “G” sensor output signal and Safing algorithm in
front direction.

OPERATION

STRUCTURE

Front passenger air bag module mainly consists of air bag and inflator which inflates air bag.

INSTALLATION

Front passenger air bag module is installed on the instrument panel with fixed bolts.

DTC Logic

INFOID:0000000003367621

DTC DETECTION LOGIC

With CONSULT-lll

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-lll.

Is malfunctioning part detected?

YES

>> Refer to

SRC-212, "Diagnosis Procedure"

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1067
B1072

ASSIST A/B MODULE
[GND-SHORT]

Front passenger air bag module circuit
is shorted to ground

• Disconnection of wiring harness and

short

• Internal breakdown in front passen-

ger air bag module

• Internal breakdown in air bag diag-

nosis sensor unit

Revision: 2008 October

2009 Murano

SRC-212

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

B1067, B1072 ASSIST A/B MODULE

CHECK AIR BAG WARNING LAMP

Check the air bag warning lamp status.
Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-305

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000003367622

With CONSULT-lll

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DIAGNOSTIC PROCEDURE

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace wiring harness.

CHECK FRONT PASSENGER AIR BAG MODULE

Replace front passenger air bag module.

Check the screen of CONSULT-lll.

Is the inspection result normal?

YES

>> INSPECTION END.

>> Check the intermittent incident. Refer to

GI-40, "Intermittent Incident"

Revision: 2008 October

2009 Murano

B1068, B1073 ASSIST A/B MODULE

SRC-213

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

SRC

B1068, B1073 ASSIST A/B MODULE

Description

INFOID:0000000003367623

DTC B1068, B1073 [SHORT] ASSIST A/B MODULE

For front passenger air bag module, crash is judged by main “G” sensor output signal and Safing algorithm in
front direction.

OPERATION

STRUCTURE

Front passenger air bag module mainly consists of air bag and inflator which inflates air bag.

INSTALLATION

Front passenger air bag module is installed on the instrument panel with fixed bolts.

DTC Logic

INFOID:0000000003367624

DTC DETECTION LOGIC

With CONSULT-lll

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-lll.

Is malfunctioning part detected?

YES

>> Refer to

SRC-214, "Diagnosis Procedure"

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1068
B1073

ASSIST A/B MODULE
[SHORT]

Front passenger air bag module circuits
are shorted to each other

• Disconnection of wiring harness and

short

• Internal breakdown in front passen-

ger air bag module

• Internal breakdown in air bag diag-

nosis sensor unit

Revision: 2008 October

2009 Murano

SRC-214

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

B1068, B1073 ASSIST A/B MODULE

CHECK AIR BAG WARNING LAMP

Check the air bag warning lamp status.
Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-305

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000003367625

With CONSULT-lll

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DIAGNOSTIC PROCEDURE

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace wiring harness.

CHECK FRONT PASSENGER AIR BAG MODULE

Replace front passenger air bag module.

Check the screen of CONSULT-lll.

Is the inspection result normal?

YES

>> INSPECTION END.

>> Check the intermittent incident. Refer to

GI-40, "Intermittent Incident"

Revision: 2008 October

2009 Murano

B1074, B1075, B1076, B1077, B1078, B1079 DIAGNOSIS SENSOR UNIT

SRC-215

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

SRC

B1074, B1075, B1076, B1077, B1078, B1079 DIAGNOSIS SENSOR UNIT

Description

INFOID:0000000003367626

DTC B1074, B1075, B1076, B1077, B1078, B1079 DIAGNOSIS SENSOR UNIT

Detects the whole SRS electrical system and displays the malfunction either by illuminating or blinking the air
bag warning lamp in the combination meter. Malfunctioning part can be detected by on board self-diagnosis
system and electro-diagnosis tester CONSULT-III.

OPERATION

It detects a shock that exceeds specified level and monitors such systems as the driver and passenger air
bag, front side air bag, side curtain air bag, pre-tensioner seat belts operate properly.

STRUCTURE

It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.

INSTALLATION

Air bag diagnosis sensor unit is installed under the center console with fixed bolts.

DTC Logic

INFOID:0000000003367627

DTC DETECTION LOGIC

With CONSULT-III

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-III)

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-III.

Is malfunctioning part detected?

YES

>> Refer to

SRC-216, "Diagnosis Procedure"

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-III)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

INSPECTION START

Turn ignition switch ON.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1074
B1075
B1076
B1077
B1078
B1079

CONTROL UNIT

Air bag diagnosis sensor unit is out of
order or mis-match

• Internal breakdown in air bag diag-

nosis sensor unit

• Mis-match between specification on

vehicle and configuration in air bag
diagnosis sensor unit

Revision: 2008 October

2009 Murano

SRC-216

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

B1074, B1075, B1076, B1077, B1078, B1079 DIAGNOSIS SENSOR UNIT

>> GO TO 2.

CHECK AIR BAG WARNING LAMP

Check the air bag warning lamp status.

Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-305

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000003367628

With CONSULT-III

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DIAGNOSTIC PROCEDURE

CHECK HARNESS CONNECTOR

Check the connection of harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness connectors.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace wiring harness.

CHECK AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit.

Check the screen of CONSULT-III.

Is the inspection result normal?

YES

>> INSPECTION END.

>> Check the intermittent incident. Refer to

GI-40, "Intermittent Incident"

Revision: 2008 October

2009 Murano

B1080, B1096 DRIVER AIRBAG MODULE

SRC-217

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

SRC

B1080, B1096 DRIVER AIRBAG MODULE

Description

INFOID:0000000004185606

For driver air bag module, crash is judged by main “G” sensor output signal and safing algorithm in front direc-
tion.

OPERATION

In case of frontal collision whose acceleration exceeds the specified level, the ignition materials are ignited by
electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This
generates hot gases that flow into the air bag through a filter and expand the bag.

STRUCTURE

Driver air bag module mainly consists of air bag and inflator that inflates air bag.

INSTALLATION

Driver air bag module is installed on the center of steering wheel with fixed bolts.

DTC Logic

INFOID:0000000004185607

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT-III

Turn ignition switch ON.

Perform “AIR BAG” Self Diagnostic Result.

Without CONSULT-III

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-177, "Diagnosis Description"

NOTE:
SRS does not enter diagnosis mode if no malfunction is detected in user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-217, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000004185608

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1080
B1096

DRIVER AIRBAG MOD-
ULE
[SHORT]

Driver air bag module circuit are shorted
to each other
(including the spiral cable)

• Disconnection of wiring harness

and short

• Malfunction in driver air bag module
• Malfunction in spiral cable
• Malfunction in air bag diagnosis sen-

sor unit

Revision: 2008 October

2009 Murano

SRC-218

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

B1080, B1096 DRIVER AIRBAG MODULE

>> Replace wiring harness.

CHECK SPIRAL CABLE CIRCUIT

Turn ignition switch OFF.

Disconnect driver air bag module harness connector and Combination switch (Spiral cable) harness con-
nector.

Check continuity between driver side air bag module harness connector and body side harness connec-
tor.

Check continuity between driver air bag module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

>> Replace spiral cable. Refer to

SR-28, "Exploded View"

REPLACE DRIVER AIR BAG MODULE

Replace driver air bag module. Refer to

SR-25, "Exploded View"

Perform DTC confirmation procedure. Refer to

SRC-217, "DTC Logic"

Is DTC detected?

YES

>> GO TO 5.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-41, "Exploded View"

Perform DTC confirmation procedure. Refer to

SRC-217, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

>> INSPECTION END

Driver side air bag module

harness connector

Terminal

Body side harness

connector

Terminal

Continuity

M302

M35

Existed

M301

Driver side air bag module harness con-

nector

Terminal

Ground

Continuity

M302

Not existed

M301

Revision: 2008 October

2009 Murano

B1081 PRE-TEN FRONT RH

SRC-219

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

SRC

B1081 PRE-TEN FRONT RH

Description

INFOID:0000000003367629

DTC B1081 [OPEN] PRE-TEN FRONT RH

For front RH seat belt pre-tensioner, crash is judged by main “G” sensor output signal and Safing algorithm in
front direction.

OPERATION

In the case of a frontal collision that exceeds specified impact level, the air bag diagnosis sensor unit detects
the deceleration caused by collision. It restrains the passenger with seat belt easing the stress on passengers
chest with load limiter.

STRUCTURE

The restraint system for front seat occupant consists of the pre-tensioner mechanism and load limiter mecha-
nism.

INSTALLATION

Front RH seat belt pre-tensioner is installed on the underside of center pillar with fixed nuts.

DTC Logic

INFOID:0000000003367630

DTC DETECTION LOGIC

With CONSULT-lll

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-lll.

Is malfunctioning part detected?

YES

>> Refer to

SRC-220, "Diagnosis Procedure"

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

INSPECTION START

Turn ignition switch ON.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1081

PRE-TEN FRONT RH
[OPEN]

Front RH seat belt pre-tensioner circuit
is open

• Disconnection of wiring harness and

open

• Internal breakdown in front RH seat

belt pre-tensioner

• Internal breakdown in air bag diag-

nosis sensor unit

Revision: 2008 October

2009 Murano

SRC-220

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

B1081 PRE-TEN FRONT RH

>> GO TO 2.

CHECK AIR BAG WARNING LAMP

Check the air bag warning lamp status.

Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-305

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000003367631

With CONSULT-lll

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DIAGNOSTIC PROCEDURE

CHECK HARNESS CONNECTOR

Check the connection of harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace wiring harness.

CHECK FRONT SEAT BELT PRE-TENSIONER

Replace front RH seat belt pre-tensioner.

Check the screen of CONSULT-lll.

Is the inspection result normal?

YES

>> INSPECTION END.

>> Check the intermittent incident. Refer to

GI-40, "Intermittent Incident"

Revision: 2008 October

2009 Murano

B1082 PRE-TEN FRONT RH

SRC-221

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

SRC

B1082 PRE-TEN FRONT RH

Description

INFOID:0000000003367632

DTC B1082 [VB-SHORT] PRE-TEN FRONT RH

For front RH seat belt pre-tensioner, crash is judged by main "G" sensor output signal and Safing algorithm in
front direction.

OPERATION

STRUCTURE

The restraint system for front seat occupant consists of the pre-tensioner mechanism and load limiter mecha-
nism.

INSTALLATION

Front RH seat belt pre-tensioner is installed on the underside of center pillar with fixed nuts.

DTC Logic

INFOID:0000000003367633

DTC DETECTION LOGIC

With CONSULT-lll

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-lll.

Is malfunctioning part detected?

YES

>> Refer to

SRC-222, "Diagnosis Procedure"

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

INSPECTION START

Turn ignition switch ON.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1082

PRE-TEN FRONT RH
[VB-SHORT]

Front RH seat belt pre-tensioner circuit
is shorted to some power supply circuit

• Disconnection of wiring harness and

short

• Internal breakdown in front RH seat

belt pre-tensioner

• Internal breakdown in air bag diag-

nosis sensor unit

Revision: 2008 October

2009 Murano

SRC-222

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

B1082 PRE-TEN FRONT RH

>> GO TO 2.

CHECK AIR BAG WARNING LAMP

Check the air bag warning lamp status.

Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-305

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000003367634

With CONSULT-lll

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DIAGNOSTIC PROCEDURE

CHECK HARNESS CONNECTOR

Check the connection of harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace wiring harness.

CHECK FRONT SEAT BELT PRE-TENSIONER

Replace front RH seat belt pre-tensioner.

Check the screen of CONSULT-lll.

Is the inspection result normal?

YES

>> INSPECTION END.

>> Check the intermittent incident. Refer to

GI-40, "Intermittent Incident"

Revision: 2008 October

2009 Murano

B1083 PRE-TEN FRONT RH

SRC-223

< COMPONENT DIAGNOSIS >

[FOR MEXICO]

SRC

B1083 PRE-TEN FRONT RH

Description

INFOID:0000000003367635

DTC B1083 [GND-SHORT] PRE-TEN FRONT RH

For front RH seat belt pre-tensioner, crash is judged by main “G” sensor output signal and Safing algorithm in
front direction.

OPERATION

In case of frontal collision that exceeds specified impact level, the air bag diagnosis sensor unit detects the
deceleration caused by collision. It restrains the passenger with seat belt easing the stress on passengers
chest with load limiter.

STRUCTURE

The restraint system for front seat occupant consists of the pre-tensioner mechanism and load limiter mecha-
nism.

INSTALLATION

Front RH seat belt pre-tensioner is installed on the underside of center pillar with fixed nuts.

DTC Logic

INFOID:0000000003367636

DTC DETECTION LOGIC

With CONSULT-lll

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-lll.

Is malfunctioning part detected?

YES

>> Refer to

SRC-224, "Diagnosis Procedure"

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

INSPECTION START

Turn ignition switch ON.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1083

PRE-TEN FRONT RH
[GND-SHORT]

Front RH seat belt pre-tensioner circuit
is shorted to ground

• Disconnection of wiring harness and

short

• Internal breakdown in front RH seat

belt pre-tensioner

• Internal breakdown in air bag diag-

nosis sensor unit

Revision: 2008 October

2009 Murano

Nissan Murano Z51 (2008 year). Manual - part 362