Nissan Murano. Manual - part 362

 

  Главная      Nissan     Nissan Murano (2014 year) - Service Manual

 

поиск по сайту            

 

 

 

 

 

 

 

 

 

содержание   ..  360  361  362  363   ..

 

 

Nissan Murano. Manual - part 362

 

 

DIAGNOSIS SYSTEM (BCM)

DLK-59

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

*: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.

ACTIVE TEST

UNLK SEN -DR

Indicates [ON/OFF] condition of driver door UNLOCK status.

PUSH SW -IPDM

Indicates [ON/OFF] condition of push-button ignition switch.

IGN RLY1 -F/B

Indicates [ON/OFF] condition of ignition relay 1.

DETE SW -IPDM

Indicates [ON/OFF] condition of P position.

SFT PN -IPDM

Indicates [ON/OFF] condition of P or N position.

SFT P -MET

Indicates [ON/OFF] condition of P position.

SFT N -MET

Indicates [ON/OFF] condition of N position.

ENGINE STATE

Indicates [STOP/START/CRANK/RUN] condition of engine states.

S/L LOCK-IPDM

Indicates [ON/OFF] condition of steering lock unit (LOCK).
NOTE:
For models without steering lock unit this item is not displayed.

S/L UNLK-IPDM

Indicates [ON/OFF] condition of steering lock unit (UNLOCK).
NOTE:
For models without steering lock unit this item is not displayed.

S/L RELAY-REQ

Indicates [ON/OFF] condition of steering lock relay.
NOTE:
For models without steering lock unit this item is not displayed.

VEH SPEED 1

Display the vehicle speed signal received from combination meter by numerical value [Km/h].

VEH SPEED 2

Display the vehicle speed signal received from ABS or VDC or CVT by numerical value [Km/h].

DOOR STAT-DR

Indicates [LOCK/READY/UNLOCK] condition of driver side door status.

DOOR STAT-AS

Indicates [LOCK/READY/UNLOCK] condition of passenger side door status.

ID OK FLAG

Indicates [SET/RESET] condition of key ID.

PRMT ENG STRT

Indicates [SET/RESET] condition of engine start possibility.

PRMT RKE STRT

NOTE:
This item is displayed, but cannot be monitored. 

KEY SW -SLOT

Indicates [ON/OFF] condition of key slot.

TRNK/HAT MNTR

NOTE:
This item is displayed, but cannot be monitored. 

RKE-LOCK

Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.

RKE-UNLOCK

Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.

RKE-TR/BD

NOTE:
This item is displayed, but cannot be monitored. 

RKE-PANIC

Indicates [ON/OFF] condition of PANIC button of Intelligent Key.

RKE-P/W OPEN

Indicates [ON/OFF] condition of P/W DOWN signal from Intelligent Key.

RKE-MODE CHG

Indicates [ON/OFF] condition of MODE CHANGE signal from Intelligent Key.

RKE OPE COUN1

When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the 
numerical value start changing.

RKE OPE COUN2

NOTE:
This item is displayed, but cannot be monitored. 

Monitor Item

Condition

Test item

Description

BATTERY SAVER

This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT screen is touched.

PW REMOTO DOWN SET

This test is able to check power window down operation.
The power window down will be activated after “ON” on CONSULT screen is touched.

DLK-60

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

TRUNK

TRUNK : CONSULT Function (BCM - TRUNK)

INFOID:0000000009718914

BCM CONSULT FUNCTION

CONSULT performs the following functions via CAN communication with BCM.

INSIDE BUZZER

This test is able to check warning chime in combination meter operation.
• Take away warning chime sounds when “TAKE OUT” on CONSULT screen is touched.
• Key warning chime sounds when “KEY WARN” on CONSULT screen is touched.
• P position warning chime sounds when “P RNG WARN” on CONSULT screen is touched.
• ACC warning chime sounds when “ACC WARN” on CONSULT screen is touched.

OUTSIDE BUZZER

This test is able to check Intelligent Key warning buzzer operation.
The Intelligent Key warning buzzer will be activated after “ON” on CONSULT screen is touched.

INDICATOR

This test is able to check warning lamp operation.
• “KEY” Warning lamp illuminates when “KEY ON” on CONSULT screen is touched.
• “KEY” Warning lamp flashes when “KEY IND” on CONSULT screen is touched.

INT LAMP

This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT screen is touched.

LCD

This test is able to check meter display information
• Engine start information displays when “BP N” on CONSULT screen is touched.
• Engine start information displays when “BP I” on CONSULT screen is touched.
• Key ID warning displays when “ID NG” on CONSULT screen is touched.
• Steering lock information displays when “ROTAT” on CONSULT screen is touched.

NOTE:
For models without steering lock unit, “ROTAT” is displayed, but cannot be tested.

• P position warning displays when “SFT P” on CONSULT screen is touched.
• Intelligent Key insert information displays when “INSRT” on CONSULT screen is touched.
• Intelligent Key low battery warning displays when “BATT” on CONSULT screen is touched.
• Take away through window warning displays when “NO KY” on CONSULT screen is touched.
• Take away warning display when “OUTKEY” on CONSULT screen is touched.
• OFF position warning display when “LK WN” on CONSULT screen is touched.

TRUNK/GLASS HATCH

This test is able to check back door opener actuator open operation.
This actuator opens when “ON” on CONSULT screen is touched.

FLASHER

This test is able to check hazard warning lamp operation.
The hazard warning lamps will be activated after “ON” on CONSULT screen is touched.

HORN

This test is able to check horn operation.
The horn will be activated after “ON” on CONSULT screen is touched.

IGN CONT2

This test is able to check ignition relay operation.
The ignition relay will be activated after “ON” on CONSULT screen is touched.

P RANGE

This test is able to check CVT shift selector power supply
CVT shift selector power is supplied when “ON” on CONSULT screen is touched.

ENGINE SW ILLUMI

This test is able to check push-ignition switch illumination operation.
Push-ignition switch illumination illuminates when “ON” on CONSULT screen is touched.

LOCK INDICATOR

NOTE:
This item is displayed, but cannot be tested.

ACC INDICATOR

This test is able to check indicator in push-ignition switch operation.
Indicator in push-button ignition switch illuminates when “ON” on CONSULT screen is touched.

IGNITION ON IND

This test is able to check indicator in push-ignition switch operation.
Indicator in push-button ignition switch illuminates when “ON” on CONSULT screen is touched.

KEY SLOT ILLUMI

This test is able to check key slot illumination operation.
Key slot illumination flash when “ON” on CONSULT screen is touched.

AUTOMATIC BACK DOOR

NOTE:
This item is displayed, but cannot be tested.

AUTOMATIC SLIDING DOOR

NOTE:
This item is displayed, but cannot be tested.

Test item

Description

DIAGNOSIS SYSTEM (BCM)

DLK-61

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

*: With back door opener system

ACTIVE TEST

Diagnosis mode

Function Description

DATA MONITOR

The BCM input/output signals are displayed.

ACTIVE TEST

The signals used to activate each device are forcibly supplied from BCM.

Monitor Item

Contents

PUSH SW

Indicates [ON/OFF] condition of push-button ignition switch.

UNLK SEN -DR

NOTE:
This item is displayed, but cannot be monitored. 

VEH SPEED 1

Indicates [Km/h] condition of vehicle speed signal from combination meter.

KEY CYL SW-TR

NOTE:
This item is displayed, but cannot be monitored. 

TR CANCEL SW

NOTE:
This item is displayed, but cannot be monitored. 

TR/BD OPEN SW

Indicates [ON/OFF] condition of back door opener switch.

TRNK/HAT MNTR

NOTE:
This item is displayed, but cannot be monitored. 

RKE-TR/BD*

NOTE:
This item is displayed, but cannot be monitored. 

Test item

Description

TRUNK/GLASS HATCH

This test is able to check back door opener actuator open operation.
This actuator opens when “”

DLK-62

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (AUTOMATIC BACK DOOR CONTROL UNIT)

DIAGNOSIS SYSTEM (AUTOMATIC BACK DOOR CONTROL UNIT)

CONSULT Function (AUTOMATIC BACK DOOR CONTROL UNIT)

INFOID:0000000009718915

APPLICATION ITEM

CONSULT performs the following functions via CAN communication with automatic back door control unit.

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

SELF-DIAG RESULT

Refer to 

DLK-255, "DTC Index"

.

Diagnosis mode

Function Description

SELF-DIAG RESULTS

Displays the diagnosis results judged by automatic back door control unit.

CAN DIAG SUPPORT MNTR

Monitors the reception status of CAN communication viewed from automatic back door 
control unit.

DATA MONITOR

The automatic back door control unit input/output signals are displayed.

ECU IDENTIFICATION

The automatic back door control unit part number is displayed.

Monitor Item

Unit

Description

VHCL SPEED MTR

[km/h]

Display the vehicle speed signal received from combination meter by nu-
merical value.

VHCL SPEED ABS

[km/h]

Display the vehicle speed signal received from ABS actuator and electrical 
unit by numerical value [km/h].

MAIN SW

[ON/OFF]

Indicates condition of main switch.

AUTO BD SW

[ON/OFF]

Indicates condition of main switch.

BK DOOR CL SW

[ON/OFF]

Indicates condition of back door close switch.

UNLOCK SEN DR

[ON/OFF]

Indicates condition of unlock sensor (driver).

OPEN SW

[ON/OFF]

Indicates condition of open switch.

CLOSE SW

[ON/OFF]

Indicates condition of close switch.

HALF LATCH SW

[ON/OFF]

Indicates condition of half latch switch.

TOUCH SEN RH

[ON/OFF/OPEN]

Indicates condition of touch sensor RH.

TOUCH SEN LH

[ON/OFF/OPEN]

Indicates condition of touch sensor LH.

P RANGE IND

[ON/OFF]

Indicates condition of P range signal from combination meter.

RKE REQ

[OFF/MOVE/

REV]

Indicates condition of remote keyless entry signal from BCM.

IGN SW

[ON/OFF]

Indicates condition of IGN power supply.

ENCODER A

[LO/HI]

Indicates condition of encoder signal from encoder A.

ENCODER B

[LO/HI]

Indicates condition of encoder signal from encoder B.

BD OPENER SW

[ON/OFF]

Indicates condition of back door opener switch.

UNLOCK SEN BD

[LOCK/

UNLOCK]

Indicates condition of unlock sensor (back door).

DESTINATION

[JPN/NAM]

Indicates specification of destination of the parts.

HAZARD

[ON/OFF]

Indicates specification of hazard warning.

 

 

 

 

 

 

 

содержание   ..  360  361  362  363   ..