Nissan Murano. Manual - part 1247

B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH

SEC-85

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH

Description

INFOID:0000000009722813

IPDM E/R confirms the shift position with the following signals.
• Transmission range switch
• Shift position signal from BCM (CAN)

DTC Logic

INFOID:0000000009722814

DTC DETECTION LOGIC

NOTE:
If DTC B210F is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to 

SEC-

31, "IPDM E/R : DTC Logic"

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON under the following conditions and wait for at least 1 second.

-

Selector lever is in the P or N position.

-

Do not depress brake pedal.

2.

Check “Self diagnostic result” with CONSULT. 

Is DTC detected?

YES

>> Go to 

SEC-85, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009722815

1.

CHECK DTC WITH BCM

Check “Self diagnostic result” with CONSULT. Refer to 

BCS-91, "DTC Index"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK TRANSMISSION RANGE SWITCH INPUT SIGNAL

1.

Turn ignition switch ON.

2.

Check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-37, "Removal and Installation"

.

NO

>> GO TO 3.

3.

CHECK TRANSMISSION RANGE SWITCH CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector and IPDM E/R connector.

3.

Check continuity between IPDM E/R harness connector and TCM harness connector.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B210F

INTER LOCK/PNP SW 
ON

IPDM E/R detects a mismatch between the sig-
nals below for 1 second or more.
• Transmission range switch input signal
• Shift position signal from BCM (CAN)

• Harness or connectors

(Transmission range switch circuit 
is open or shorted)

• Transmission range switch

(+)

(–)

Condition

Voltage (V)

(Approx.)

IPDM E/R

Connector

Terminal

E10

30

Ground

Selector lever

P or N

Battery voltage

Other than above

0

SEC-86

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH

4.

Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-37, "Removal and Installation"

.

NO

>> Repair or replace harness or connector.

IPDM E/R

TCM

Continuity

Connector

Terminal

Connector

Terminal

E10

72

F23

20

Existed

IPDM E/R

Ground

Continuity

Connector

Terminal

E10

72

Not existed

B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH

SEC-87

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH

Description

INFOID:0000000009722816

IPDM E/R confirms the shift position with the following signals.
• Transmission range switch
• Shift position signal from BCM (CAN)

DTC Logic

INFOID:0000000009722817

DTC DETECTION LOGIC

NOTE:
If DTC B2110 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to 

SEC-

31, "IPDM E/R : DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn the ignition switch ON under the following conditions and wait for at least 1 second.

-

Selector lever is in the P or N position.

-

Do not depress brake pedal.

2.

Check “Self diagnostic result” with CONSULT.

Is DTC detected?

YES

>> Go to 

SEC-87, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009722818

1.

CHECK DTC WITH TCM

Check “Self diagnostic result” with CONSULT. Refer to 

TM-128, "DTC Index"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK TRANSMISSION RANGE SWITCH INPUT SIGNAL

1.

Turn ignition switch ON.

2.

Check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-37, "Removal and Installation"

.

NO

>> GO TO 3.

3.

CHECK TRANSMISSION RANGE SWITCH CIRCUIT

DTC No.

Trouble diagnosis 

name

DTC detecting condition

Possible cause

B2110

INTER LOCK/PNP 
SW 

IPDM E/R detects mismatch between the signals 
below for 1 second or more.
• Transmission range switch input signal
• Shift position signal from BCM (CAN)

• Harness or connectors

(Transmission range switch circuit is 
open or shorted)

• Transmission range switch
• IPDM E/R
• BCM

(+)

(–)

Condition

Voltage (V)

(Approx.)

IPDM E/R

Connector

Terminal

E10

30

Ground

Selector lever

P or N

Battery voltage

Other than above

0

SEC-88

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector and IPDM E/R connector.

3.

Check continuity between IPDM E/R harness connector and TCM harness connector.

4.

Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-37, "Removal and Installation"

.

NO

>> Repair or replace harness or connector.

IPDM E/R

TCM

Continuity

Connector

Terminal

Connector

Terminal

E10

72

F23

20

Existed

IPDM E/R

Ground

Continuity

Connector

Terminal

E10

72

Not existed