Nissan Murano. Manual - part 1244

B2617 STARTER RELAY CIRCUIT

SEC-73

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

4.

Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-37, "Removal and Installation"

.

NO

>> Repair or replace harness or connector.

3.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

>> INSPECTION END

IPDM E/R

BCM

Continuity

Connector

Terminal

Connector

Terminal

E11

46

M121

52

Existed

IPDM E/R

Ground

Continuity

Connector

Terminal

E11

46

Not existed

SEC-74

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2619 BCM

B2619 BCM

Description

INFOID:0000000009722792

BCM requests IPDM E/R to supply power to steering lock unit. After receiving the power, the steering lock unit
transmits an ON signal to BCM.

DTC Logic

INFOID:0000000009722793

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Press the push-button ignition switch under the following conditions and wait for at least 1 second.

-

Selector lever is in the P or N position.

-

Do not depress brake pedal.

2.

Check “Self diagnostic result” with CONSULT.

Is DTC detected?

YES

>> Go to 

SEC-74, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009722794

1.

INSPECTION START

1.

Turn ignition switch ON.

2.

Check “Self diagnostic result” with CONSULT.

3.

Touch “ERASE”.

4.

Perform DTC Confirmation Procedure.
See 

SEC-74, "DTC Logic"

.

Is the DTC B2619 displayed again?

YES

>> Replace BCM. Refer to 

BCS-98, "Removal and Installation"

.

NO

>> INSPECTION END

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B2619

BCM

BCM detects a mismatch between the power supplied to the 
steering lock unit and the feedback for one second or more.

BCM

B261A PUSH-BUTTON IGNITION SWITCH

SEC-75

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B261A PUSH-BUTTON IGNITION SWITCH

Description

INFOID:0000000009722795

BCM transmits the change in the power supply position with the push-button ignition switch to IPDM E/R via
the CAN communication. IPDM E/R transmits the power supply position status via CAN communication to
BCM.

DTC Logic

INFOID:0000000009722796

DTC DETECTION LOGIC

NOTE:
• If DTC B261A is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

SEC-31, "BCM : DTC Logic"

.

• If DTC B261A is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

SEC-33, "BCM : DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE 1

1.

Press push-button ignition switch for 1 second under the following condition.

-

Selector lever is in the P or N position.

-

Do not depress brake pedal.

2.

Check “Self diagnostic result” with CONSULT.

Is DTC detected?

YES

>> Go to 

SEC-75, "Diagnosis Procedure"

NO

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE 2

1.

Insert Intelligent Key into the key slot.

2.

Press the push-button ignition switch under the following conditions and wait for at least 1 second.

-

Selector lever is in the P or N position.

-

Do not depress brake pedal.

3.

Check “Self diagnostic result” with CONSULT.

Is DTC detected?

YES

>> Go to 

SEC-75, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009722797

1.

INSPECTION START

Perform inspection in accordance with procedure that confirms DTC.

Which procedure confirms DTC?

DTC confirmation procedure 1>>GO TO 2.
DTC confirmation procedure 2>>GO TO 4.

2.

CHECK PUSH-BUTTON IGNITION SWITCH OUTPUT SIGNAL 1

1.

Turn ignition switch OFF.

2.

Disconnect push-button ignition switch connector and IPDM E/R connector.

DTC No.

Trouble diagnosis 

name

DTC detecting condition

Possible cause

B261A

PUSH-BTN IGN 
SW

BCM detects the mismatch between the following for 
1 second or more
• Power supply position with push-button ignition 

switch

• Power supply position from IPDM E/R (CAN)

• Harness or connectors

(Push-button ignition switch circuit is 
open or shorted)

• Between BCM and push-button igni-

tion switch

• Between IPDM E/R and push-button 

ignition switch

SEC-76

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B261A PUSH-BUTTON IGNITION SWITCH

3.

Check voltage between push-button ignition switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> GO TO 3.

3.

CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT 1

1.

Disconnect BCM connector.

2.

Check continuity between push-button ignition switch harness connector and BCM harness connector.

3.

Check continuity between push-button ignition switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace harness or connector.

4.

CHECK PUSH-BUTTON IGNITION SWITCH OUTPUT SIGNAL 2

1.

Turn ignition switch OFF.

2.

Disconnect push-button ignition switch connector and BCM connector.

3.

Check voltage between push-button ignition switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> GO TO 5.

5.

CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT 2

1.

Disconnect IPDM E/R connector.

2.

Check continuity between push-button ignition switch harness connector and IPDM E/R harness connec-
tor.

3.

Check continuity between push-button ignition switch harness connector and ground.

(+)

(–)

Voltage (V)

(Approx.)

Push-button ignition switch

Connector

Terminal

M101

4

Ground

Battery voltage

Push-button ignition switch

BCM

Continuity

Connector

Terminal

Connector

Terminal

M101

4

M121

60

Existed

Push-button ignition switch

Ground

Continuity

Connector

Terminal

M101

4

Not existed

(+)

(–)

Voltage (V)

(Approx.)

Push-button ignition switch

Connector

Terminal

M101

4

Ground

Battery voltage

Push-button ignition switch

IPDM E/R

Continuity

Connector

Terminal

Connector

Terminal

M101

4

E10

28

Existed

Push-button ignition switch

Ground

Continuity

Connector

Terminal

M101

4

Not existed