Nissan Murano. Manual

Interview the customer to obtain the malfunction information (conditions and environment when the malfunc-
tion occurred) as much as possible when the customer brings the vehicle in.

>> GO TO 2.

REPRODUCE THE MALFUNCTION INFORMATION

Check the malfunction on the vehicle that the customer describes.
Inspect the relation of the symptoms and the condition when the symptoms occur.

>> GO TO 3.

IDENTIFY THE MALFUNCTIONING SYSTEM WITH “SYMPTOM DIAGNOSIS”

Use “Symptom diagnosis” from the symptom inspection result in step 2 and then identify where to start per-
forming the diagnosis based on possible causes and symptoms.

>> GO TO 4.

IDENTIFY THE MALFUNCTIONING PARTS WITH “COMPONENT DIAGNOSIS”

Perform the diagnosis with “Component diagnosis” of the applicable system.

>> GO TO 5.

REPAIR OR REPLACE THE MALFUNCTIONING PARTS

Repair or replace the specified malfunctioning parts.

>> GO TO 6.

FINAL CHECK

Check that malfunctions are not reproduced when obtaining the malfunction information from the customer,
referring to the symptom inspection result in step 2.

Are the malfunctions corrected?

YES

>> INSPECTION END

>> GO TO 3.

INSPECTION AND ADJUSTMENT

PWC-5

< BASIC INSPECTION >

PWC

INSPECTION AND ADJUSTMENT

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : De-
scription

INFOID:0000000009723115

When battery negative terminal is disconnected, initialization is necessary.
If any of the following operations are performed, initialization is necessary as well as when battery negative
terminal is disconnected.
• Power supply to the power window control unit is cut off by the removal f battery terminal or the battery fuse

is blown.

• Disconnection and connection of power window control unit harness connector.
• Removal and installation of motor from regulator assembly.
• Operation of regulator assembly as an independent unit.
• Removal and installation of rear power window control unit.
• Removal and installation of door glass.
• Removal and installation of door glass run.
The operations as per the following cannot be performed while initialization is not complete.
• AUTO-UP operation
• Anti-pinch function
• Door key cylinder switch power window function

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Spe-
cial Repair Requirement

INFOID:0000000009723116

INITIALIZATION PROCEDURE

Disconnect battery negative terminal or power window control unit connector. Reconnect it after a minute
or more.

Turn ignition switch ON.

Operate power window switch to fully open door glass. (This operation is unnecessary if door glass is
already fully open.)

Pull and hold power window switch UP (AUTO-UP operation). Even after door glass stops at the fully
closed position, pull the switch for 2 seconds or more.

Initialization procedure is complete.

Inspect anti-pinch function.

CHECK ANTI-PINCH FUNCTION

Fully open door glass.

Place a piece of wood near the fully closed position.

Close door glass completely using AUTO-UP.

• Check that door glass lowers approximately 150 mm (5.9 in) without pinching piece of wood and stops.
• Check that door glass does not rise when operating power window main switch while lowering.

CAUTION:

• Perform initialization when AUTO-UP operation or anti-pinch function does not operate normally.
• Check that AUTO-UP operates before inspection when initialization is performed.
• Never check with hands or other body parts because they may be pinched. Never get pinched.
• It may switch to the fail-safe mode if open/close operation is performed continuously without fully

closing door glass. Perform initialization in the above situation. Refer to

PWC-89, "Fail Safe"

• Finish initialization. Otherwise, the next operation cannot be done.
1.

AUTO-UP operation

Anti-pinch function

Door key cylinder switch power window function

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description

INFOID:0000000009723117

When the control unit is replaced, initialization is necessary.
If any of the following operations are performed, initialization is necessary as well as when the control unit is
disconnected.

Nissan Murano. Manual - part 1116