Nissan Murano. Manual - part 18

ADP-64

< DTC/CIRCUIT DIAGNOSIS >

LIFTING SWITCH (REAR)

Is the inspection result normal?

YES

>> Replace driver seat control unit. Refer to 

ADP-210, "Removal and Installation"

.

NO

>> Repair or replace harness or connector.

3.

CHECK LIFTING SWITCH (REAR)

Refer to 

ADP-64, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace power seat switch. Refer to 

ADP-213, "Removal and Installation"

.

4.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection

INFOID:0000000009720696

1.

CHECK LIFTING SWITCH (REAR)

1.

Turn ignition switch OFF.

2.

Disconnect power seat switch (lifting switch rear) connector.

3.

Check continuity between power seat switch (lifting switch rear) terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace power seat switch. Refer to 

ADP-213, "Removal and Installation"

.

Driver seat control unit

Ground

Continuity 

Connector

Terminal

B452

15

Not existed

16

Power seat switch (lifting switch rear)

Condition

Continuity

Terminal

35

15

Lifting switch rear (up)

Operate

Existed

Release

Not existed

16

Lifting switch rear (down)

Operate

Existed

Release

Not existed

TILT SWITCH

ADP-65

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

TILT SWITCH

Description

INFOID:0000000009720697

Tilt switch is equipped to the steering column. The operation signal is inputted to the automatic drive positioner
control unit when the tilt switch is operated.

Component Function Check

INFOID:0000000009720698

1.

CHECK FUNCTION

1.

Select “TILT SW-UP”, “TILT SW-DOWN” in “Data monitor” mode with CONSULT. 

2.

Check tilt switch signal under the following conditions.

Is the indication normal?

YES

>> INSPECTION END

NO

>> Perform diagnosis procedure. Refer to 

ADP-65, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009720699

1.

CHECK TILT SWITCH SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect tilt & telescopic switch connector.

3.

Turn ignition switch ON.

4.

Check voltage between tilt & telescopic switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK TILT SWITCH CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect automatic drive positioner control unit connector.

3.

Check continuity between automatic drive positioner control unit harness connector and tilt & telescopic
switch harness connector.

4.

Check continuity between automatic drive positioner control unit harness connector and ground.

Monitor item

Condition

Status

TILT SW-UP

Tilt switch (up)

Operate

ON

Release

OFF

TILT SW-DOWN

Tilt switch (down)

Operate

ON

Release

OFF

(+)

(–)

Voltage (V)

(Approx.)

Tilt & telescopic switch

Connector

Terminals

M102

2

Ground

5

3

Automatic drive positioner control unit

Tilt & telescopic switch

Continuity

Connector

Terminal

Connector

Terminal

M75

1

M102

2

Existed

13

3

ADP-66

< DTC/CIRCUIT DIAGNOSIS >

TILT SWITCH

Is the inspection result normal?

YES

>> Replace automatic drive positioner control unit. Refer to 

ADP-211, "Removal and Installation"

.

NO

>> Repair or replace harness or connector.

3.

CHECK TILT SWITCH

Refer to 

ADP-66, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace tilt & telescopic switch. Refer to 

ADP-214, "Removal and Installation"

.

4.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection

INFOID:0000000009720700

1.

CHECK TILT SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect tilt & telescopic switch connector.

3.

Check continuity between tilt & telescopic switch terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace tilt & telescopic switch. Refer to 

ADP-214, "Removal and Installation"

.

Automatic drive positioner control unit

Ground

Continuity 

Connector

Terminal

M75

1

Not existed

13

Tilt switch

Condition

Continuity

Terminal

1

2

Tilt switch (upward)

Operate

Existed

Release

Not existed

3

Tilt switch (downward)

Operate

Existed

Release

Not existed

TELESCOPIC SWITCH

ADP-67

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

TELESCOPIC SWITCH

Description

INFOID:0000000009720701

Telescopic switch is equipped to the steering column. The operation signal is inputted to the automatic drive
positioner control unit when the telescopic switch is operated.

Component Function Check

INFOID:0000000009720702

1.

CHECK FUNCTION

1.

Select “TELESCO SW-FR”, “TELESCO SW-RR” in “Data monitor” mode with CONSULT. 

2.

Check telescopic switch signal under the following conditions.

Is the indication normal?

YES

>> INSPECTION END

NO

>> Perform diagnosis procedure. Refer to 

ADP-67, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009720703

1.

CHECK TELESCOPIC SWITCH SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect tilt & telescopic switch connector.

3.

Turn ignition switch ON.

4.

Check voltage between tilt & telescopic switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK TELESCOPIC SWITCH CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect automatic drive positioner control unit connector.

3.

Check continuity between automatic drive positioner control unit harness connector and tilt & telescopic
switch harness connector.

4.

Check continuity between automatic drive positioner control unit harness connector and ground.

Monitor item

Condition

Status

TELESCO SW-FR

Telescopic switch (forward)

Operate

ON

Release

OFF

TELESCO SW-RR

Telescopic switch (backward)

Operate

ON

Release

OFF

(+)

(–)

Voltage (V)

(Approx.)

Tilt & telescopic switch

Connector

Terminals

M102

5

Ground

5

4

Automatic drive positioner control unit

Tilt & telescopic switch

Continuity

Connector

Terminal

Connector

Terminal

M75

7

M102

5

Existed

19

4