Nissan X-Trail 32. Manual - part 908

 

  Главная      Nissan     Nissan X-Trail 32 - Service Manual

 

поиск по сайту            

 

 

 

 

 

 

 

 

 

содержание   ..  906  907  908  909   ..

 

 

Nissan X-Trail 32. Manual - part 908

 

 

P2127, P2128 APP SENSOR

EC-761

< DTC/CIRCUIT DIAGNOSIS >

[QR25DE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK SENSOR POWER SUPPLY 2 CIRCUIT

Perfor

EC-794, "Diagnosis Procedure"

.

Is inspection result normal?

YES

>> Perform the trouble diagnosis for power supply circuit.

NO

>> Repair or replace error-detected parts.

3.

CHECK APP SENSOR 2 GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect ECM harness connector.

3.

Check the continuity between APP sensor harness connector and ECM harness connector.

4.

Also check harness for short to power.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace error-detected parts.

4.

CHECK APP SENSOR 2 INPUT SIGNAL CIRCUIT

1.

Check the continuity between APP sensor harness connector and ECM harness connector.

2.

Also check harness for short to ground and to power.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace error-detected parts

5.

CHECK APP SENSOR

Check the APP sensor. Refer to 

EC-761, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Replace accelerator pedal assembly. Refer to 

ACC-4, "Removal and Installation"

.

6.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection

INFOID:0000000010986470

1.

CHECK ACCELERATOR PEDAL POSITION SENSOR

1.

Turn ignition switch OFF.

2.

Reconnect all harness connectors disconnected.

3.

Turn ignition switch ON.

4.

Check the voltage between ECM harness connector terminals as per the following condition.

+

Continuity

APP sensor

ECM

Connector

Terminal

Connector

Terminal

E110

1

E60

120

Existed

+

Continuity

APP sensor

ECM

Connector

Terminal

Connector

Terminal

E110

6

E60

119

Existed

EC-762

< DTC/CIRCUIT DIAGNOSIS >

[QR25DE]

P2127, P2128 APP SENSOR

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace accelerator pedal assembly. Refer to 

ACC-4, "Removal and Installation"

.

ECM

Condition

Voltage

Connector

+

Terminal

Sensor 1

E60

126

127

Accelerator pedal

Fully released

0.5 - 1.0 V

Fully depressed

4.2 - 4.8 V

Sensor 2

119

120

Fully released

0.25 - 0.5 V

Fully depressed

2.0 - 2.5 V

P2135 TP SENSOR

EC-763

< DTC/CIRCUIT DIAGNOSIS >

[QR25DE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

P2135 TP SENSOR

DTC Description

INFOID:0000000010986471

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Harness or connectors (TP sensor 1 or 2 circuit is open or shorted.)
• Electric throttle control actuator (TP sensor 1 or 2)

FAIL-SAFE

• The ECM controls the electric throttle control actuator in regulating the throttle opening in order for the idle

position to be within +10 degrees.

• The ECM regulates the opening speed of the throttle valve to be slower than the normal condition. So, the

acceleration will be poor.

DTC CONFIRMATION PROCEDURE

1.

CHECK DTC PRIORITY

If DTC P2135 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.

Is applicable DTC detected?

YES

>> Perform diagnosis of applicable. Refer to 

EC-707, "DTC Description"

.

NO

>> GO TO 2.

2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1.

Turn ignition switch OFF and wait at least 10 seconds.

2.

Turn ignition switch ON.

3.

Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.

>> GO TO 3.

3.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Start engine and let it idle for 1 second.

2.

Check DTC.

Is DTC detected?

YES

>> Proceed to 

EC-763, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010986472

1.

CHECK DTC PRIORITY

If DTC P2135 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.

Is applicable DTC detected?

YES

>> Perform diagnosis of applicable. Refer to 

EC-707, "DTC Description"

.

NO

>> GO TO 2.

2.

CHECK THROTTLE POSITION SENSOR POWER SUPPLY

1.

Turn ignition switch OFF.

2.

Disconnect electric throttle control actuator harness connector.

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detecting condition

P2135

TP SENSOR-B1
(Throttle/pedal position sensor/switch 

A

 / 

B

 voltage correlation)

Rationally incorrect voltage is sent to ECM compared with the signals from 
TP sensor 1 and TP sensor 2.

EC-764

< DTC/CIRCUIT DIAGNOSIS >

[QR25DE]

P2135 TP SENSOR

3.

Turn ignition switch ON.

4.

Check the voltage between electric throttle control actuator harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 3.

3.

CHECK THROTTLE POSITION SENSOR POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect ECM harness connector.

3.

Check the continuity between electric throttle control actuator harness connector and ground.

4.

Also check harness for short to ground.

Is the inspection result normal?

YES

>> Perform the trouble diagnosis for power supply circuit.

NO

>> Repair or replace error-detected parts.

4.

CHECK THROTTLE POSITION SENSOR GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect ECM harness connector.

3.

Check the continuity between electric throttle control actuator harness connector and ECM harness con-
nector.

4.

Also check harness for short to power.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace error-detected parts.

5.

CHECK THROTTLE POSITION SENSOR INPUT SIGNAL CIRCUIT

1.

Check the continuity between electric throttle control actuator harness connector and ECM harness con-
nector.

+

Voltage

(Approx.)

Electric throttle control actuator

Connector

Terminal

F113

2

Ground

5 V

+

Continuity

Electric throttle control actu-

ator

ECM

Connector

Terminal

Connector

Terminal

F113

2

F68

80

Existed

+

Continuity

Electric throttle control actu-

ator

ECM

Connector

Terminal

Connector

Terminal

F113

4

F68

78

Existed

+

Continuity

Electric throttle control actu-

ator

ECM

Connector

Terminal

Connector

Terminal

F113

1

F68

79

Existed

3

77

 

 

 

 

 

 

 

содержание   ..  906  907  908  909   ..