Nissan X-Trail 32. Manual - part 368

DAS

CONFIGURATION (CHASSIS CONTROL MODULE)

DAS-213

< BASIC INSPECTION >

[CHASSIS CONTROL]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

CONFIGURATION (CHASSIS CONTROL MODULE)

Work Procedure

INFOID:0000000010721705

CAUTION:

• Use “Manual Configuration” only when “TYPE ID” of the chassis control module cannot be read.
• After configuration, turn the ignition switch from OFF to ON and check that the chassis control warn-

ing to information display of combination meter displays OFF after staying illuminated for approxi-
mately two seconds.

• If an error occurs during configuration, start over from the beginning.

1.

CHECKING TYPE ID (1)

Use FAST (service parts catalogue) to search the chassis control module of the applicable vehicle and find
“Type ID”.

Is “Type ID” displayed?

YES

>> Print out “Type ID”, and GO TO 2.

NO

>> “Configuration” is not required for the chassis control module. Replace in the usual manner. Refer

to 

DAS-278, "Removal and Installation"

.

2.

CHECKING TYPE ID (2)

CONSULT Configuration

1.

Select “Before Replace ECU” of “Read/Write Configuration”.

2.

Check that “Type ID” is displayed on the CONSULT screen.

Is “Type ID” displayed?

YES

>> GO TO 3.

NO

>> GO TO 7.

3.

VERIFYING TYPE ID (1)

CONSULT Configuration

Compare a “Type ID” displayed on the CONSULT screen with the one searched by using FAST (service parts
catalogue) to check that these “Type ID” agree with each other.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.

>> GO TO 4.

4.

SAVING TYPE ID

CONSULT Configuration

Save “Type ID” on CONSULT.

>> GO TO 5.

5.

REPLACING CHASSIS CONTROL MODULE (1)

Replace the chassis control module. Refer to 

DAS-278, "Removal and Installation"

.

>> GO TO 6.

6.

WRITING (AUTOMATIC WRITING)

CONSULT Configuration

1.

Select “After Replace ECU” of “Re/programming, Configuration” or that of “Read / Write Configuration”.

2.

Select the “Type ID” agreeing with the one stored on CONSULT and the one searched by using FAST
(service parts catalogue) to write the “Type ID” into the chassis control module.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.

>> GO TO 9.

7.

REPLACING CHASSIS CONTROL MODULE (2)

DAS-214

< BASIC INSPECTION >

[CHASSIS CONTROL]

CONFIGURATION (CHASSIS CONTROL MODULE)

Replace the chassis control module. Refer to 

DAS-278, "Removal and Installation"

.

>> GO TO 8.

8.

WRITING (MANUAL WRITING)

CONSULT Configuration

1.

Select “Manual Configuration”.

2.

Select the “Type ID” searched by using FAST (service parts catalogue) to write the “Type ID” into the
chassis control module.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.

>> GO TO 9.

9.

VERIFYING TYPE ID (2)

CONSULT Configuration

Compare “Type ID” written into the chassis control module with the one searched by using FAST (service parts
catalogue) to check that these “Type ID” agree with each other.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.

>> GO TO 10.

10.

CHECKING CHASSIS CONTROL WARNING

1.

Turn the ignition switch OFF.

2.

Turn the ignition switch ON and check that the “Chassis Control” warning to information display of combi-
nation meter displays OFF. 

CAUTION:

Never start the engine.

Is the inspection result normal?

YES

>> GO TO 11.

NO

>> Perform self-diagnosis for “CHASSIS CONTROL”.

11.

PERFORMING SUPPLEMENTARY WORK

With CONSULT

1.

Perform “All DTC Reading”.

2.

Record or print self-diagnosis results and freeze frame data (FFD).

3.

Erase self-diagnosis results.

>> End of work.

DAS

C1B92-00 BRAKE CONTROL SYSTEM

DAS-215

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

DTC/CIRCUIT DIAGNOSIS

C1B92-00 BRAKE CONTROL SYSTEM

DTC Description

INFOID:0000000010721706

DTC DETECTION LOGIC

POSSIBLE CAUSE

• ABS actuator and electric unit (control unit) system
• Chassis control module

FAIL-SAFE

The following functions are suspended.
• Active trace control function
• Active engine brake function
• Active ride control function

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1.

Turn the ignition switch OFF to ON.

CAUTION:

Be sure to wait of 10 seconds after turning ignition switch OFF or ON.

2.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1B92-00” detected?

YES

>> Proceed to 

DAS-215, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-44, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010721707

1.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

With CONSULT

Perform self-diagnosis for “ABS”.

Is DTC detected?

YES

>> Check the DTC. Refer to 

BRC-84, "DTC Index"

.

NO

>> GO TO 2.

2.

PERFORM SELF-DIAGNOSIS

With CONSULT

1.

Erase self-diagnosis result for “CHASSIS CONTROL”.

2.

Turn the ignition switch OFF and wait for 10 seconds or more.

3.

Turn the ignition switch ON.

4.

Perform “All DTC Reading”.

Are DTC “C1B92-00”, “U1000-00” or other DTC detected?

DTC

Display Item

(Trouble diagnosis content)

Malfunction detected condition

C1B92-00

BRAKE CONTROL SYSTEM
(Brake control system)

When a malfunction is detected in ABS actuator and electric unit (control unit) sys-
tem.

DAS-216

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C1B92-00 BRAKE CONTROL SYSTEM

YES (“C1B92-00”)>>Replace the chassis control module. Refer to 

DAS-278, "Removal and Installation"

.

YES (“U1000-00”)>>Refer to 

LAN-17, "Trouble Diagnosis Flow Chart"

.

YES (other DTC)>>Check the DTC.
NO

>> INSPECTION END