Nissan X-Trail 32. Manual - part 1883

 

  Главная      Nissan     Nissan X-Trail 32 - Service Manual

 

поиск по сайту            

 

 

 

 

 

 

 

 

 

содержание   ..  1881  1882  1883  1884   ..

 

 

Nissan X-Trail 32. Manual - part 1883

 

 

INTRUDER SENSOR

SEC-299

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

INTRUDER SENSOR

Component Function Check

INFOID:0000000010926602

1.

CHECK INTRUDER SENSOR FUNCTION

1.

Turn ignition switch OFF.

2.

Check that hood is closed completely.

3.

Get in the vehicle and close all doors.

4.

Lock doors using Keyfob.

5.

Check security indicator lamp blinks to confirm that the vehicle security system is shifted into the ARMED
phase. Refer to 

SEC-217, "VEHICLE SECURITY SYSTEM : System Description"

.

6.

Hold up and move a hand over intruder sensor.

7.

Check that siren sounds after a few seconds.

Does the siren sound?

YES

>> Intruder sensor is OK.

NO

>> Refer to 

SEC-299, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010926603

1.

CHECK INTRUDER SENSOR POWER SUPPLY

1.

Turn ignition switch OFF.

2.

Disconnect sensor cancel switch connector.

3.

Check voltage between sensor cancel switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO-1

>> Check 5 A fuse [No. 14, located in the fuse block].

NO-2

>> Check harness for open or short between fuse and sensor cancel switch.

2.

CHECK INTRUDER SENSOR SIGNAL CIRCUIT

1.

Disconnect siren control unit connector.

2.

Check continuity between siren control unit harness connector and sensor cancel switch harness connec-
tor.

3.

Check continuity between siren control unit harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK INTRUDER SENSOR GROUND CIRCUIT

Check continuity between sensor cancel switch harness connector and ground.

(+)

(–)

Voltage

(Approx.)

Sensor cancel switch

Connector

Terminal

R25

1

Ground

Battery voltage

Siren control unit

Sensor cancel switch

Continuity 

Connector

Terminal

Connector

Terminal

B127

4

R25

2

Existed

Siren control unit

Ground

Continuity 

Connector

Terminal

B127

4

Not existed

SEC-300

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

INTRUDER SENSOR

Is the inspection result normal?

YES

>> Replace intruder sensor.

NO

>> Repair or replace harness.

Sensor cancel switch

Ground

Continuity 

Connector

Terminal

R25

3

Existed

SENSOR CANCEL SWITCH

SEC-301

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

SENSOR CANCEL SWITCH

Diagnosis Procedure

INFOID:0000000010926604

1.

CHECK SENSOR CANCEL SWITCH SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect sensor cancel switch connector.

3.

Check signal between sensor cancel switch harness connector and ground with oscilloscope.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK SENSOR CANCEL SWITCH CIRCUIT

1.

Disconnect BCM connector.

2.

Check continuity between BCM harness connector and sensor cancel switch harness connector.

3.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-121, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK GROUND CIRCUIT

Check continuity between sensor cancel switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK SENSOR CANCEL SWITCH

Refer to 

SEC-302, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

(+)

(–)

Voltage

Sensor cancel switch

Connector

Terminal

R25

5

Ground

JPMIA0011GB

BCM

Sensor cancel switch

Continuity

Connector

Terminal

Connector

Terminal

M86

107

R25

5

Existed

BCM

Ground

Continuity 

Connector

Terminal

M86

107

Not existed

Sensor cancel switch

Ground

Continuity

Connector

Terminal

R25

6

Existed

SEC-302

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

SENSOR CANCEL SWITCH

NO

>> Replace sensor cancel switch.

5.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection

INFOID:0000000010926605

1.

CHECK SENSOR CANCEL SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect sensor cancel switch connector.

3.

Check continuity between sensor cancel switch terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace sensor cancel switch.

Sensor cancel switch

Condition

Continuity

Terminal

5

6

Sensor cancel switch

Press

Existed

Release

Not existed

 

 

 

 

 

 

 

содержание   ..  1881  1882  1883  1884   ..