Nissan X-Trail 32. Manual - part 52

AV-200

< DTC/CIRCUIT DIAGNOSIS >

[WITH NAVIGATION]

U111D SIDE CAMERA LH IMAGE SIGNAL CIRCUIT

YES

>> Replace around view monitor control unit. Refer to 

AV-268, "Removal and Installation"

.

NO

>> Replace side camera LH. Refer to 

AV-271, "Removal and Installation"

.

AV

U112F EPS CIRCUIT

AV-201

< DTC/CIRCUIT DIAGNOSIS >

[WITH NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

U112F EPS CIRCUIT

DTC Description

INFOID:0000000010923282

DTC DETECTION LOGIC

POSSIBLE CAUSE

EPS

FAIL-SAFE

Around view monitor with Park Assist is cancel

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

WITH CONSULT

1.

Turn the ignition switch ON

2.

Perform “All DTC Reading” with CONSULT.

3.

Check if the “U112F” is detected as the current malfunction in “Self Diagnostic Result” of “AVM”.

“U112F” detected as the current malfunction?

YES

>> Refer to 

AV-201, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-44, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010923283

1.

CHECK SELF-DIAGNOSIS RESULTS

With CONSULT.

Check if the “U1000” is detected other than “U112F” in “Self Diagnostic Result” of “AVM”. 
“U1000” detected?

YES

>> Perform the CAN communication system inspection. Repair or replace the malfunctioning parts.

Refer to 

AV-178, "AROUND VIEW MONITOR CONTROL UNIT : Diagnosis Procedure"

.

NO

>> GO TO 2.

2.

CHECK SELF-DIAGNOSIS RESULTS

With CONSULT.

Check if any DTC is detected in “Self Diagnostic Result” of “EPS/DAST3”. 
Is any DTC detected?

YES

>> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to

STC-21, "DTC Index"

.

NO

>> Replace the around view monitor control unit. Refer to 

AV-268, "Removal and Installation"

. 

DTC

Trouble diagnosis

(Trouble diagnosis contents)

DTC detecting condition

U112F

EPS CIRC
(EPS circuit)

The around view monitor control unit detects that EPS has a malfunction.

AV-202

< DTC/CIRCUIT DIAGNOSIS >

[WITH NAVIGATION]

U1217 NAVI CONTROL UNIT

U1217 NAVI CONTROL UNIT

DTC Description

INFOID:0000000010714857

DTC DETECTION LOGIC

POSSIBLE CAUSE

NAVI control unit

FAIL-SAFE

The function of some multi-AV systems does not operate

DTC CONFIRMATION PROCEDURE

NOTE:
• The auto ACC function allows the accessory power supply for a certain period of time even after ignition

switch OFF. For this reason, when performing diagnosis, turn the ignition switch OFF and wait for 3 minutes
with the driver's door opened.

• The operation of the vehicle during standby may cause an accessory power supply.

1.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1.

Turn ignition switch ON.

2.

Turn ignition switch OFF and wait for 3 minutes with the driver's door opened.

3.

Turn ignition switch ON and wait at least 30 seconds or more.

4.

Select “Self Diagnostic Result” mode of “MULTI AV” using CONSULT.

5.

Check DTC.

Is DTC U1217 detected?

YES

>> Proceed to 

AV-202, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-44, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010714858

1.

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

With CONSULT

1.

Turn ignition switch ON.

2.

Erase DTC.

3.

Perform DTC confirmation procedure again. Refer to 

AV-202, "DTC Description"

.

Is DTC U1217 detected again?

YES

>> Replace NAVI control unit. Refer to 

AV-262, "Removal and Installation"

.

NO

>> INSPECTION END

DTC

Trouble diagnosis

(Trouble diagnosis contents)

Detecting condition

U1217

BLUETOOTH MODULE
(Bluetooth module connection)

NAVI control unit malfunction is detected.

AV

U1229 NAVI CONTROL UNIT

AV-203

< DTC/CIRCUIT DIAGNOSIS >

[WITH NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

U1229 NAVI CONTROL UNIT

DTC Description

INFOID:0000000010714859

DTC DETECTION LOGIC

POSSIBLE CAUSE

NAVI control unit

FAIL-SAFE

The function of some multi-AV systems does not operate

DTC CONFIRMATION PROCEDURE

NOTE:
• The auto ACC function allows the accessory power supply for a certain period of time even after ignition

switch OFF. For this reason, when performing diagnosis, turn the ignition switch OFF and wait for 3 minutes
with the driver's door opened.

• The operation of the vehicle during standby may cause an accessory power supply.

1.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1.

Turn ignition switch ON.

2.

Turn ignition switch OFF and wait for 3 minutes with the driver's door opened.

3.

Turn ignition switch ON and wait at least 30 seconds.

4.

Select “Self Diagnostic Result” mode of “MULTI AV” using CONSULT.

5.

Check DTC.

Is DTC U1229 detected?

YES

>> Proceed to 

AV-203, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-44, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010714860

1.

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

With CONSULT

1.

Turn ignition switch ON.

2.

Erase DTC.

3.

Perform DTC confirmation procedure again. Refer to 

AV-203, "DTC Description"

.

Is DTC U1229 detected again?

YES

>> Replace NAVI control unit. Refer to 

AV-262, "Removal and Installation"

.

NO

>> INSPECTION END

DTC

Trouble diagnosis

(Trouble diagnosis contents)

Detecting condition

U1229

iPod CERTIFICATION
(iPod certification error)

NAVI control unit malfunction is detected.