Qashqai J11. Exterior Lighting system - part 7

B20D0 HEADLAMP (LO) LH POWER SUPPLY CIRCUIT

EXL-97

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

B20D0 HEADLAMP (LO) LH POWER SUPPLY CIRCUIT

DTC Description

INFOID:0000000010452544

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Harness or connector
• Front combination lamp LH internal circuit
- LED [Headlamp (LO)]
- LED headlamp control module
- Harness
• IPDM E/R

FAIL-SAFE

Shuts off the power supply to the headlamp (LO) LH power supply circuit until the headlamp (LO) ON condi-
tions are no longer satisfied.

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

With CONSULT

1.

Turn ignition switch ON.

2.

Select “HL (LO) LH CIRC MALFUNCTN” in “Data Monitor” mode of “IPDM E/R” using CONSULT.

3.

Check the monitor status.

What is the monitor status?

“0”

>> GO TO 2.

“1”

>> A short circuit is detected multiple times in the headlamp (LO) LH power supply circuit, and dam-

age accumulates at the smart FET inside the IPDM E/R. For this reason, IPDM E/R does not turn
ON the smart FET. Because the DTC cannot be reproduced in this state, perform 

EXL-97, "Diag-

nosis Procedure"

 and replace IPDM E/R after the malfunctioning part is repaired. Refer to 

PCS-

67, "Removal and Installation"

. 

2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1.

Turn ignition switch OFF.

2.

Turn ignition switch ON.

3.

Turn lighting switch 2ND.

4.

Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

5.

Check DTC.

Is DTC detected?

YES

>> Refer to 

EXL-97, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010452545

1.

CHECK HEADLAMP (LO) LH POWER SUPPLY CIRCUIT (SHORT)

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

B20D0

HL (LO) LH PWR SPLY CIRC
[Headlamp (low) left hand power supply cir-
cuit]

[CIRC 
SHORT TO 
GRND]

When headlamp (LO) ON conditions are satisfied (smart 
FET inside IPDM E/R is ON), and overcurrent is detected 
in the headlamp (LO) LH power supply circuit.

Monitor item

Monitor status

HL (LO) LH CIRC MALFUNCTN

0

1

EXL-98

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

B20D0 HEADLAMP (LO) LH POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Turn lighting switch OFF.

3.

Disconnect IPDM E/R connector and front combination lamp LH connector.

4.

Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness.

2.

CHECK HEADLAMP (LO) LH POWER SUPPLY

With CONSULT

1.

Connect IPDM E/R connector.

2.

Turn ignition switch ON

3.

Select “HEADLAMP (LO)” in “Active Test” mode of “IPDM E/R” using CONSULT.

4.

With operating the test items, check the voltage between front combination lamp LH harness connector
and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace IPDM E/R. Refer to 

PCS-67, "Removal and Installation"

.

3.

CHECK HEADLAMP (LO) LH

Check the headlamp (LO) LH. Refer to 

EXL-98, "Component Inspection"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace front combination lamp LH. Refer to 

EXL-161, "Removal and Installation"

.

Component Inspection

INFOID:0000000010452546

1.

CHECK HEADLAMP (LO) LH

1.

Turn ignition switch OFF.

2.

Disconnect front combination lamp LH connector.

3.

Check resistance of front combination lamp LH terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace front combination lamp LH. Refer to 

EXL-161, "Removal and Installation"

.

IPDM E/R 

—

Continuity

Connector

Terminal

E102

58

Ground

Not existed

+

-

Test item

Voltage

Front combination lamp LH

Connector

Terminal

E91

1

Ground

HEADLAMP 
(LO)

On

9 – 16 V

Off

0 – 1 V

Front combination lamp LH

Resistance

Terminal

1

2

Except 0 

Ω

B20D1 HEADLAMP (LO) RH POWER SUPPLY CIRCUIT

EXL-99

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

B20D1 HEADLAMP (LO) RH POWER SUPPLY CIRCUIT

DTC Description

INFOID:0000000010452547

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Harness or connector
• Front combination lamp RH internal circuit
- LED [Headlamp (LO)]
- LED headlamp control module
- Harness
• IPDM E/R

FAIL-SAFE

Shuts off the power supply to the headlamp (LO) RH power supply circuit until the headlamp (LO) ON condi-
tions are no longer satisfied.

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

With CONSULT

1.

Turn ignition switch ON.

2.

Select “HL (LO) RH CIRC MALFUNCTN” in “Data Monitor” mode of “IPDM E/R” using CONSULT.

3.

Check the monitor status.

What is the monitor status?

“0”

>> GO TO 2.

“1”

>> A short circuit is detected multiple times in the headlamp (LO) RH power supply circuit, and dam-

age accumulates at the smart FET inside the IPDM E/R. For this reason, IPDM E/R does not turn
ON the smart FET. Because the DTC cannot be reproduced in this state, perform 

EXL-99, "Diag-

nosis Procedure"

 and replace IPDM E/R after the malfunctioning part is repaired. Refer to 

PCS-

67, "Removal and Installation"

. 

2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1.

Turn ignition switch OFF.

2.

Turn ignition switch ON.

3.

Turn lighting switch 2ND.

4.

Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

5.

Check DTC.

Is DTC detected?

YES

>> Refer to 

EXL-99, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010452548

1.

CHECK HEADLAMP (LO) RH POWER SUPPLY CIRCUIT (SHORT)

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

B20D1

HL (LO) RH PWR SPLY CIRC
[Headlamp (low) left hand power supply cir-
cuit]

[CIRC 
SHORT TO 
GRND]

When headlamp (LO) ON conditions are satisfied (smart 
FET inside IPDM E/R is ON), and overcurrent is detected 
in the headlamp (LO) RH power supply circuit.

Monitor item

Monitor status

HL (LO) RH CIRC MALFUNCTN

0

1

EXL-100

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

B20D1 HEADLAMP (LO) RH POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Turn lighting switch OFF.

3.

Disconnect IPDM E/R connector and front combination lamp RH connector.

4.

Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness.

2.

CHECK HEADLAMP (LO) RH POWER SUPPLY

With CONSULT

1.

Connect IPDM E/R connector.

2.

Turn ignition switch ON

3.

Select “HEADLAMP (LO)” in “Active Test” mode of “IPDM E/R” using CONSULT.

4.

With operating the test items, check the voltage between front combination lamp RH harness connector
and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace IPDM E/R. Refer to 

PCS-67, "Removal and Installation"

.

3.

CHECK HEADLAMP (LO) RH

Check the headlamp (LO) RH. Refer to 

EXL-100, "Component Inspection"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace front combination lamp RH. Refer to 

EXL-161, "Removal and Installation"

.

Component Inspection

INFOID:0000000010452549

1.

CHECK HEADLAMP (LO) RH

1.

Turn ignition switch OFF.

2.

Disconnect front combination lamp RH connector.

3.

Check resistance of front combination lamp RH terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace front combination lamp RH. Refer to 

EXL-161, "Removal and Installation"

.

IPDM E/R 

—

Continuity

Connector

Terminal

E101

54

Ground

Not existed

+

-

Test item

Voltage

Front combination lamp RH

Connector

Terminal

E93

1

Ground

HEADLAMP 
(LO)

On

9 – 16 V

Off

0 – 1 V

Front combination lamp RH

Resistance

Terminal

1

2

Except 0 

Ω

B20D2 PARKING LAMP POWER SUPPLY CIRCUIT

EXL-101

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

B20D2 PARKING LAMP POWER SUPPLY CIRCUIT

DTC Description

INFOID:0000000010452550

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Harness or connector
• Front combination lamp LH internal circuit
- LED (Parking lamp)
- Control circuit
- Harness
• Front combination lamp RH internal circuit
- LED (Parking lamp)
- Control circuit
- Harness
• IPDM E/R

FAIL-SAFE

Shuts off the power supply to the parking lamp (LH/RH) power supply circuit until the parking lamp, license
plate lamp, and tail lamp ON conditions are no longer satisfied.

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

With CONSULT

1.

Turn ignition switch ON.

2.

Select “P LAMP CIRC MALFUNCTN” in “Data Monitor” mode of “IPDM E/R” using CONSULT.

3.

Check the monitor status.

What is the monitor status?

“0”

>> GO TO 2.

“1”

>> A short circuit is detected multiple times in the parking lamp LH or parking lamp RH power supply

circuit, and damage accumulates at the smart FET inside the IPDM E/R. For this reason, IPDM E/
R does not turn ON the smart FET. Because the DTC cannot be reproduced in this state, perform

EXL-102, "Diagnosis Procedure"

 and replace IPDM E/R after the malfunctioning part is repaired.

Refer to 

PCS-67, "Removal and Installation"

. 

2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1.

Turn ignition switch OFF.

2.

Turn ignition switch ON.

3.

Turn lighting switch 1ST.

4.

Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

5.

Check DTC.

Is DTC detected?

YES

>> Refer to 

EXL-102, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

B20D2

PARKING LAMP PWR SPLY CIRC
(Parking lamp power supply circuit)

[CIRC 
SHORT TO 
GRND]

When the parking lamp, license plate lamp, and tail lamp 
ON conditions are satisfied (smart FET inside IPDM E/R 
is ON), and overcurrent is detected in the parking lamp LH 
power supply circuit or parking lamp RH power supply cir-
cuit.

Monitor item

Monitor status

P LAMP CIRC MALFUNCTN

0

1

EXL-102

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

B20D2 PARKING LAMP POWER SUPPLY CIRCUIT

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010452551

1.

CHECK PARKING LAMP POWER SUPPLY CIRCUIT (SHORT)

1.

Turn ignition switch OFF.

2.

Turn lighting switch OFF.

3.

Disconnect IPDM E/R connector and front combination lamp connector.

4.

Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness.

2.

CHECK PARKING LAMP POWER SUPPLY

With CONSULT

1.

Connect IPDM E/R connector.

2.

Turn ignition switch ON

3.

Select “PARKING LAMP” in “Active Test” mode of “IPDM E/R” using CONSULT.

4.

With operating the test items, check the voltage between front combination lamp harness connector and
ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace IPDM E/R. Refer to 

PCS-67, "Removal and Installation"

.

3.

CHECK PARKING LAMP

Check the parking lamp. Refer to 

EXL-102, "Component Inspection"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace the corresponding front combination lamp. Refer to 

EXL-161, "Removal and Installation"

.

Component Inspection

INFOID:0000000010452552

1.

CHECK PARKING LAMP

1.

Turn ignition switch OFF.

2.

Disconnect front combination lamp connector.

3.

Check resistance of front combination lamp terminals.

Parking lamp LH

IPDM E/R 

—

Continuity

Connector

Terminal

RH

E101

53

Ground

Not existed

LH

E102

64

+

-

Test item

Voltage

Front combination lamp

Connector

Terminal

RH

E93

5

Ground

PARKING 
LAMP

On

9 – 16 V

Off

0 – 1 V

LH

E91

On

9 – 16 V

Off

0 – 1 V

Front combination lamp LH

Resistance

Terminal

5

6

Except 0 

Ω

B20D2 PARKING LAMP POWER SUPPLY CIRCUIT

EXL-103

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Parking lamp RH

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace the corresponding front combination lamp. Refer to 

EXL-161, "Removal and Installation"

.

Front combination lamp RH

Resistance

Terminal

5

6

Except 0 

Ω

EXL-104

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

B20D4 TAIL LAMP LH POWER SUPPLY CIRCUIT

B20D4 TAIL LAMP LH POWER SUPPLY CIRCUIT

DTC Description

INFOID:0000000010452553

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Harness or connector
• Rear combination lamp LH (body side) internal circuit
- LED (Tail lamp)
- Harness
• Rear combination lamp LH (back door side) internal circuit
- LED (Tail lamp)
- Harness
• License plate lamp LH bulb
• License plate lamp RH bulb
• License plate lamp LH bulb socket
• License plate lamp RH bulb socket
• IPDM E/R

FAIL-SAFE

Shuts off the power supply to the following power supply circuits until the parking lamp, license plate lamp, and
tail lamp ON conditions are no longer satisfied.
• Tail lamp LH (body side)
• Tail lamp LH (back door side)
• License plate lamp LH
• License plate lamp RH

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

With CONSULT

1.

Turn ignition switch ON.

2.

Select “T LAMP LH CIRC MALFUNCTN” in “Data Monitor” mode of “IPDM E/R” using CONSULT.

3.

Check the monitor status.

What is the monitor status?

“0”

>> GO TO 2.

“1”

>> A short circuit is detected multiple times in the tail lamp LH (body side), tail lamp LH (back door

side), license plate lamp LH or license plate lamp RH power supply circuit, and damage accumu-
lates at the smart FET inside the IPDM E/R. For this reason, IPDM E/R does not turn ON the
smart FET. Because the DTC cannot be reproduced in this state, perform 

EXL-105, "Diagnosis

Procedure"

 and replace IPDM E/R after the malfunctioning part is repaired. Refer to 

PCS-67,

"Removal and Installation"

. 

2.

PERFORM DTC CONFIRMATION PROCEDURE

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

B20D4

TAIL LAMP LH PWR SPLY CIRC
(Tail lamp left hand power supply circuit)

[CIRC 
SHORT TO 
GRND]

When the parking lamp, license plate lamp, and tail lamp 
ON conditions are satisfied (smart FET inside IPDM E/R 
is ON), and overcurrent is detected in the following power 
supply circuit.
• Tail lamp LH (body side)
• Tail lamp LH (back door side)
• License plate lamp LH
• License plate lamp RH

Monitor item

Monitor status

T LAMP LH CIRC MALFUNCTN

0

1

B20D4 TAIL LAMP LH POWER SUPPLY CIRCUIT

EXL-105

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

With CONSULT

1.

Turn ignition switch OFF.

2.

Turn ignition switch ON.

3.

Turn lighting switch 1ST.

4.

Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

5.

Check DTC.

Is DTC detected?

YES

>> Refer to 

EXL-105, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010452554

1.

CHECK TAIL LAMP LH POWER SUPPLY CIRCUIT (SHORT)

1.

Turn ignition switch OFF.

2.

Turn lighting switch OFF.

3.

Disconnect the following connectors.

-

IPDM E/R

-

Stop lamp / tail lamp LH (body side)

-

Tail lamp LH (back door side)

-

License plate lamp LH

-

License plate lamp RH

4.

Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness.

2.

CHECK TAIL LAMP LH POWER SUPPLY

With CONSULT

1.

Connect IPDM E/R connector.

2.

Turn ignition switch ON

3.

Select “TAIL LAMP” in “Active Test” mode of “IPDM E/R” using CONSULT.

4.

With operating the test items, check the voltage between stop lamp / tail lamp (body side) harness con-
nector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace IPDM E/R. Refer to 

PCS-67, "Removal and Installation"

.

3.

CHECK TAIL LAMP LH

Check the tail lamp LH. Refer to 

EXL-106, "Component Inspection (Tail Lamp)"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning part.

4.

CHECK LICENSE PLATE LAMP

IPDM E/R 

—

Continuity

Connector

Terminal

E37

4

Ground

Not existed

+

-

Test item

Voltage

Stop lamp / tail lamp (body side)

Connector

Terminal

B22

3

Ground

TAIL LAMP

On

9 – 16 V

Off

0 – 1 V

EXL-106

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

B20D4 TAIL LAMP LH POWER SUPPLY CIRCUIT

Check the license plate lamp. Refer to 

EXL-106, "Component Inspection (License Plate Lamp)"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair or replace the malfunctioning part.

Component Inspection (Tail Lamp)

INFOID:0000000010452555

1.

CHECK TAIL LAMP LH

1.

Turn ignition switch OFF.

2.

Disconnect stop lamp / tail lamp LH (body side) and tail lamp LH (back door side) connector.

3.

Check resistance of stop lamp / tail lamp LH (body side) and tail lamp LH (back door side) terminals.

Tail lamp LH (body side)

Tail lamp LH (back door side)

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace the corresponding rear combination lamp. Refer to 

EXL-174, "Removal and Installation"

.

Component Inspection (License Plate Lamp)

INFOID:0000000010452556

1.

CHECK LICENSE PLATE LAMP

1.

Turn ignition switch OFF.

2.

Disconnect license plate lamp connector.

3.

Check resistance of license plate lamp terminals.

License plate lamp LH

License plate lamp RH

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK LICENSE PLATE LAMP

1.

Remove license plate lamp bulb.

2.

Check resistance of license plate lamp terminals.

License plate lamp LH

Stop lamp / tail lamp LH (body side)

Resistance

Terminal

3

2

Except 0 

Ω

Tail lamp LH (back door side)

Resistance

Terminal

1

2

Except 0 

Ω

License plate lamp LH

Resistance

Terminal

1

2

Except 0 

Ω

License plate lamp RH

Resistance

Terminal

1

2

Except 0 

Ω

License plate lamp LH

Resistance

Terminal

1

2

Except 0 

Ω

B20D4 TAIL LAMP LH POWER SUPPLY CIRCUIT

EXL-107

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

License plate lamp RH

Is the inspection result normal?

YES

>> Replace the corresponding license plate lamp bulb. Refer to 

EXL-178, "Replacement"

.

NO

>> Repair or replace the corresponding license plate lamp bulb socket.

License plate lamp RH

Resistance

Terminal

1

2

Except 0 

Ω

EXL-108

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

B20D5 TAIL LAMP RH POWER SUPPLY CIRCUIT

B20D5 TAIL LAMP RH POWER SUPPLY CIRCUIT

DTC Description

INFOID:0000000010452557

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Harness or connector
• Rear combination lamp RH (body side) internal circuit
- LED (Tail lamp)
- Harness
• Rear combination lamp RH (back door side) internal circuit
- LED (Tail lamp)
- Harness
• IPDM E/R

FAIL-SAFE

Shuts off the power supply to the following power supply circuits until the parking lamp, license plate lamp, and
tail lamp ON conditions are no longer satisfied.
• Tail lamp RH (body side)
• Tail lamp RH (back door side)

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

With CONSULT

1.

Turn ignition switch ON.

2.

Select “T LAMP RH CIRC MALFUNCTN” in “Data Monitor” mode of “IPDM E/R” using CONSULT.

3.

Check the monitor status.

What is the monitor status?

“0”

>> GO TO 2.

“1”

>> A short circuit is detected multiple times in the tail lamp RH (body side) or tail lamp RH (back door

side) power supply circuit, and damage accumulates at the smart FET inside the IPDM E/R. For
this reason, IPDM E/R does not turn ON the smart FET. Because the DTC cannot be reproduced
in this state, perform 

EXL-109, "Diagnosis Procedure"

 and replace IPDM E/R after the malfunc-

tioning part is repaired. Refer to 

PCS-67, "Removal and Installation"

. 

2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1.

Turn ignition switch OFF.

2.

Turn ignition switch ON.

3.

Turn lighting switch 1ST.

4.

Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

5.

Check DTC.

Is DTC detected?

YES

>> Refer to 

EXL-109, "Diagnosis Procedure"

.

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

B20D5

TAIL LAMP RH PWR SPLY CIRC
(Tail lamp right hand power supply circuit)

[CIRC 
SHORT TO 
GRND]

When the parking lamp, license plate lamp, and tail lamp 
ON conditions are satisfied (smart FET inside IPDM E/R 
is ON), and overcurrent is detected in the following power 
supply circuit.
• Tail lamp RH (body side)
• Tail lamp RH (back door side)

Monitor item

Monitor status

T LAMP RH CIRC MALFUNCTN

0

1

B20D5 TAIL LAMP RH POWER SUPPLY CIRCUIT

EXL-109

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010452558

1.

CHECK TAIL LAMP RH POWER SUPPLY CIRCUIT (SHORT)

1.

Turn ignition switch OFF.

2.

Turn lighting switch OFF.

3.

Disconnect the following connectors.

-

IPDM E/R

-

Stop lamp / tail lamp RH (body side)

-

Tail lamp RH (back door side)

4.

Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness.

2.

CHECK TAIL LAMP RH POWER SUPPLY

With CONSULT

1.

Connect IPDM E/R connector.

2.

Turn ignition switch ON

3.

Select “TAIL LAMP” in “Active Test” mode of “IPDM E/R” using CONSULT.

4.

With operating the test items, check the voltage between stop lamp / tail lamp (body side) harness con-
nector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace IPDM E/R. Refer to 

PCS-67, "Removal and Installation"

.

3.

CHECK TAIL LAMP RH

Check the tail lamp RH. Refer to 

EXL-109, "Component Inspection"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair or replace the malfunctioning part.

Component Inspection

INFOID:0000000010452559

1.

CHECK TAIL LAMP RH

1.

Turn ignition switch OFF.

2.

Disconnect stop lamp / tail lamp RH (body side) and tail lamp RH (back door side) connector.

3.

Check resistance of stop lamp / tail lamp RH (body side) and tail lamp RH (back door side) terminals.

Tail lamp RH (body side)

IPDM E/R 

—

Continuity

Connector

Terminal

E37

17

Ground

Not existed

+

-

Test item

Voltage

Stop lamp / tail lamp (body side)

Connector

Terminal

B79

3

Ground

TAIL LAMP

On

9 – 16 V

Off

0 – 1 V

Stop lamp / tail lamp RH (body side)

Resistance

Terminal

3

2

Except 0 

Ω

EXL-110

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

B20D5 TAIL LAMP RH POWER SUPPLY CIRCUIT

Tail lamp RH (back door side)

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace the corresponding rear combination lamp. Refer to 

EXL-174, "Removal and Installation"

.

Tail lamp RH (back door side)

Resistance

Terminal

1

2

Except 0 

Ω

B20DB HEIGHT SENSOR INITIALIZE NOT DONE

EXL-111

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

B20DB HEIGHT SENSOR INITIALIZE NOT DONE

DTC Description

INFOID:0000000010452560

DTC DETECTION LOGIC

POSSIBLE CAUSE

[MISSING CALIBRATION]

Sensor initialize is not completed

[NOT CONFIURED]

Configuration is not completed

FAIL-SAFE

Right and left headlamp aiming motors fix at the initial aiming position.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1.

Turn ignition switch ON.

2.

Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

3.

Check DTC.

Is DTC detected?

YES

>> Refer to 

EXL-111, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010452561

1.

CHECK DTC

Perform each inspection according to the displayed DTC.

Which DTC is displayed?

[MISSING CALIBRATION]>>GO TO 2.
[NOT CONFIURED]>>GO TO 3.

2.

PERFORM SENSOR INITIALIZE

Perform sensor initialize. Refer to 

EXL-74, "Work Procedure"

.

>> INSPECTION END

3.

PERFORM CONFIGURATION

Perform configuration for “HLL” of IPDM E/R. Refer to 

PCS-53, "Work Procedure"

.

>> INSPECTION END

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

B20DB

HEIGHT SENS INITIALIZE NOT DONE
(Height Sensor Initialize not done)

[MISSING 
CALIBRA-
TION]

Initialization incomplete status of the height sensor is de-
tected when the ignition switch is turned ON.

[NOT CON-
FIURED]

“HLL” vehicle specification is not written to IPDM E/R 
when ignition switch is turned ON.

EXL-112

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

B20E2 LED HEADLAMP RH

B20E2 LED HEADLAMP RH

DTC Description

INFOID:0000000010452562

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Harness or connector
• Front combination lamp RH internal circuit
- LED [Headlamp (LO)]
- LED headlamp control module
- Harness
• IPDM E/R

FAIL-SAFE

Transmits the headlamp warning signal (CAN communication) to the combination meter when the headlamp
(LO) ON conditions are satisfied. (When the ignition switch turns ON, the headlamp warning is displayed on
the information display of the combination meter.)

DTC CONFIRMATION PROCEDURE

1.

CHECK DTC PRIORITY

If DTC B20E2 is displayed with DTC B20D1, first perform the confirmation procedure (trouble diagnosis) for
DTC B20D1.
Is applicable DTC detected?

YES

>> Perform diagnosis of applicable. Refer to 

EXL-99, "DTC Description"

.

NO

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1.

Turn ignition switch ON.

2.

Turn lighting switch 2ND and wait at least 2 seconds or more.

3.

Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

4.

Check DTC.

Is DTC detected?

YES

>> Refer to 

EXL-112, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010452563

1.

CHECK HEADLAMP (LO) RH OPERATION

With CONSULT

1.

Turn ignition switch ON.

2.

Select “HEADLAMP (LO)” in “Active Test” mode of “IPDM E/R” using CONSULT.

3.

With operating the test items, check that the headlamp (LO) RH is turned ON.

Is the inspection result normal?

YES

>> GO TO 2.

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

B20E2

LED HEADLAMP RH
(Light emitting diode headlamp right hand)

[CMPNENT 
INTERNAL 
MLFNCTN]

When headlamp (LO) ON conditions are satisfied, and 
the headlamp warning RH signal voltage that is input from 
the LED headlamp control module is 2.2 V or more con-
tinually for 2 seconds or more.

On

: Headlamp (LO) RH ON

Off

: Headlamp (LO) RH OFF