Nissan Qashqai J11. Manual - part 750

 

  Index      Nissan     Nissan Qashqai J11 - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  748  749  750  751   ..

 

 

Nissan Qashqai J11. Manual - part 750

 

 

P0966 PRESSURE CONTROL SOLENOID B

TM-575

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

NO

>> There is malfunction of primary pressure solenoid valve. Replace transaxle assembly. Refer to

TM-653, "Removal and Installation"

.

TM-576

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

P0967 PRESSURE CONTROL SOLENOID B

P0967 PRESSURE CONTROL SOLENOID B

DTC Logic

INFOID:0000000010245649

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1.

Start the engine and wait for 5 seconds or more.

2.

Check the first trip DTC.

Is “P0967” detected?

YES

>> Go to 

TM-576, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010245650

1.

CHECK CIRCUIT BETWEEN TCM AND CVT UNIT

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector and CVT unit connector.

3.

Check continuity between TCM harness connector terminal and ground. 

Is the inspection result normal?

YES 

>> GO TO 2.

NO

>> Repair or replace damaged parts.

2.

CHECK CIRCUIT BETWEEN CVT UNIT AND GROUND

Check continuity between CVT unit harness connector terminal and ground. 

Is the inspection result normal?

YES >> Check 

intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

Possible causes

P0967

PC SOLENOID B
(Pressure Control Solenoid B 
Control Circuit High)

When all of the following conditions are satis-
fied and this state is maintained for 0.2 sec-
onds:
• TCM power supply voltage: More than 11 V
• P0966 is not detected
• TCM judges that solenoid valve circuit is 

open.

• Harness or connector

(Primary pressure solenoid valve cir-
cuit open or shorted to power supply)

• Primary pressure solenoid valve

TCM

CVT unit

Continuity

Connector

Terminal

Connector

Terminal

F1

40

F58

2

Existed

CVT unit

Condition

Resistance

Connector

Terminal

F207

2

Ground

CVT fluid temperature: 20

°

C (68

°

F)

5.5 – 7.0 

CVT fluid temperature: 50

°

C (122

°

F)

6.0 – 8.0 

CVT fluid temperature: 80

°

C (176

°

F)

6.5 – 8.5 

P0967 PRESSURE CONTROL SOLENOID B

TM-577

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

NO

>> There is malfunction of primary pressure solenoid valve. Replace transaxle assembly. Refer to

TM-653, "Removal and Installation"

.

TM-578

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

P1586 G SENSOR

P1586 G SENSOR

DTC Logic

INFOID:0000000010249638

DTC DETECTION LOGIC

NOTE:
DC stands for “DRIVING CYCLE” and indicates a series of driving cycle of “Ignition switch OFF 

ON 

 driv-

ing 

 OFF”.

DTC CONFIRMATION PROCEDURE

CAUTION:

Be careful of the driving speed.

1.

PREPARATION BEFORE WORK

If another “DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1.

Start the engine.

2.

Drive the vehicle for 5 seconds or more.

3.

Stop the vehicle.

CAUTION:

Never stop the engine.

4.

Repeat step 2 through 3.

5.

Check the DTC.

“P1586”detected?

YES

>> Go to 

TM-578, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010249639

1.

CHECK G SENSOR SIGNAL

With CONSULT

1.

Park the vehicle on a level surface.

2.

Turn ignition switch ON.

3.

Select “Data Monitor” in “TRANSMISSION”

4.

Select “G SEN SLOPE”.

5.

Swing the vehicle and check if value varies between 

40.45% and 40.45%.

DTC

Trouble diagnosis name

DTC detection condition

Possible causes

P1586

G Sensor Circuit Electrical

When 1 or 2 is satisfied and maintained for 5 seconds or 
more, and this state is satisfied two times within the same 
DC:
1.

When all of the following conditions are satisfied: 

-

G sensor detection voltage: 0.675 V or less

-

TCM power supply voltage: More than 11 V

2.

When all of the following conditions are satisfied: 

-

G sensor detection voltage: 3.13 V or more

-

TCM power supply voltage: More than 11 V

• Harness or connector

(G sensor circuit)

• G sensor

Monitor item

Condition

Standard

G SEN SLOPE

Flat road

0%

Uphill

Positive value (Maximum 40.45%)

Downhill

Negative value (Minimum 

40.45%)

 

 

 

 

 

 

 

Content   ..  748  749  750  751   ..