Nissan Qashqai J11. Manual - part 748

P0890 TCM

TM-567

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Refer to 

GI-41, "Intermittent Incident"

.

Is the inspection result normal?

YES 

>> Replace TCM. Refer to 

TM-625, "Removal and Installation"

.

NO

>> Repair or replace malfunctioning parts.

TM-568

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

P0962 PRESSURE CONTROL SOLENOID A

P0962 PRESSURE CONTROL SOLENOID A

DTC Logic

INFOID:0000000010245641

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1.

Start the engine and wait for 5 seconds or more.

2.

Check the first trip DTC.

Is “P0962” detected?

YES

>> Go to 

TM-568, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010245642

1.

CHECK CIRCUIT BETWEEN TCM AND CVT UNIT

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector and CVT unit connector.

3.

Check continuity between TCM harness connector terminal and ground. 

Is the inspection result normal?

YES 

>> GO TO 2.

NO

>> Repair or replace damaged parts.

2.

CHECK CIRCUIT BETWEEN CVT UNIT AND GROUND

Check continuity between CVT unit harness connector terminal and ground. 

Is the inspection result normal?

YES >> Check 

intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

Possible causes

P0962

PC SOLENOID A
(Pressure Control Solenoid A 
Control Circuit Low)

When all of the following conditions are satis-
fied and this state is maintained for 0.2 sec-
onds:
• TCM power supply voltage: More than 11 V
• TCM judges that solenoid valve circuit is 

shorted to ground. 

• Harness or connector

(Line pressure solenoid valve circuit is 
shorted to ground)

• Line pressure solenoid valve

TCM

—

Continuity

Connector

Terminal

F1

30

Ground

Not existed

CVT unit

—

Condition

Resistance

Connector

Terminal

F207

1

Ground

CVT fluid temperature: 20

°

C (68

°

F)

5.5 – 7.0 

Ω

CVT fluid temperature: 50

°

C (122

°

F)

6.0 – 8.0 

Ω

CVT fluid temperature: 80

°

C (176

°

F)

6.5 – 8.5 

Ω

P0962 PRESSURE CONTROL SOLENOID A

TM-569

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

NO

>> There is malfunction of line pressure solenoid valve. Replace transaxle assembly. Refer to 

TM-

653, "Removal and Installation"

.

TM-570

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

P0963 PRESSURE CONTROL SOLENOID A

P0963 PRESSURE CONTROL SOLENOID A

DTC Logic

INFOID:0000000010245643

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1.

Start the engine and wait for 5 seconds or more.

2.

Check the first trip DTC.

Is “P0963” detected?

YES

>> Go to 

TM-570, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010245644

1.

CHECK CIRCUIT BETWEEN TCM AND CVT UNIT

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector and CVT unit connector.

3.

Check continuity between TCM harness connector terminal and ground. 

Is the inspection result normal?

YES 

>> GO TO 2.

NO

>> Repair or replace damaged parts.

2.

CHECK CIRCUIT BETWEEN CVT UNIT AND GROUND

Check continuity between CVT unit harness connector terminal and ground. 

Is the inspection result normal?

YES >> Check 

intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

Possible causes

P0963

PC SOLENOID A
(Pressure Control Solenoid A 
Control Circuit High)

When all of the following conditions are satis-
fied and this state is maintained for 0.2 sec-
onds:
• TCM power supply voltage: More than 11 V
• P0962 is not detected
• TCM judges that solenoid valve circuit is 

open. 

• Harness or connector

(Line pressure solenoid valve circuit is 
open or shorted to power supply)

• Line pressure solenoid valve

TCM

CVT unit

Continuity

Connector

Terminal

Connector

Terminal

F1

30

F58

1

Existed

CVT unit

—

Condition

Resistance

Connector

Terminal

F207

1

Ground

CVT fluid temperature: 20

°

C (68

°

F)

5.5 – 7.0 

Ω

CVT fluid temperature: 50

°

C (122

°

F)

6.0 – 8.0 

Ω

CVT fluid temperature: 80

°

C (176

°

F)

6.5 – 8.5 

Ω