Nissan Qashqai J11. Manual - part 740

P0715 INPUT SPEED SENSOR A

TM-535

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

1.

Connect all of disconnected connectors.

2.

Lift the vehicle.

3.

Start the engine.

4.

Check frequency of primary speed sensor.

Is the inspection result normal?

YES 

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> Replace primary speed sensor. Refer to 

TM-634, "Removal and Installation"

.

6.

DETECT MALFUNCTIONING ITEMS

Check the following items:
• Open circuit or short circuit in harness between ignition switch and primary speed sensor. Refer to 

PG-56,

"Wiring Diagram - IGNITION POWER SUPPLY -"

.

• 10A fuse [No.74, located in fuse block (J/B)]. Refer to 

PG-97, "Fuse, Connector and Terminal Arrangement"

.

• IPDM E/R
Is the check result normal?

YES

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

+

−

Condition

Frequency

(Approx.)

TCM

Connector

Terminal

F1

35

Ground

• Shift position: “M1” position
• Vehicle speed: 20 km/h (12 MPH)

700 Hz

JSDIA1905GB

TM-536

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

P0717 INPUT SPEED SENSOR A

P0717 INPUT SPEED SENSOR A

DTC Logic

INFOID:0000000010245611

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Always drive vehicle at a safe speed.

1.

PREPARATION BEFORE WORK

If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1.

Start the engine.

2.

Drive the vehicle.

3.

Maintain the following conditions for 10 seconds or more.

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

Possible cause

P0717

INPUT SPEED SENSOR A
(Input/Turbine Speed Sensor 
“A” Circuit No Signal)

When 1 is satisfied and any of 2, 3 or 4 is satisfied:
1.

When the following conditions are satisfied:

-

TCM power supply voltage: More than 11 V

-

After range change completion, it spends 2 
seconds or more.

2.

When all of the following conditions are satis-
fied and this state is maintained for 5 sec-
onds:

-

Primary pulley speed: 500 rpm or more

-

Input speed: Less than 150 rpm

-

Range: Other than P, N

-

P0705, P0706, or P0715 is not detected.

3.

When all of the following conditions are satis-
fied and this state is maintained for 0.5 sec-
onds:

-

10-msec-ago input speed: 1,000 rpm or more

-

Now input speed: 0 rpm

4.

When all of the following conditions are satis-
fied and this state is maintained for 5 sec-
onds:

-

Range: D or Ds

-

Engine speed: 450 rpm or more

-

Input peed: 300 rpm or more

-

Primary pulley speed: 300 rpm or more

-

Secondary pulley seed: 300 rpm or more

-

Differences between engine speed and pri-
mary pulley speed: 1,000 rpm or less

-

Differences between primary pulley speed 
and input speed: More than 1,000 rpm

-

Differences between engine speed and input 
speed: More than 1,000 rpm

-

Lock-up command is being given (except for 
slip lock-up)

-

DTC other than the applicable DTC is not de-
tected.

• Harness or connectors

(Input speed sensor circuit is open 
or shorted.)

•  Input speed sensor

Selector lever

: “D” position

P0717 INPUT SPEED SENSOR A

TM-537

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

4.

Stop the vehicle.

5.

Check the first trip DTC.

Is “P0717” detected?

YES

>> Go to 

TM-537, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010245612

1.

CHECK INPUT SPEED SENSOR POWER CIRCUIT 

1.

Turn ignition switch OFF.

2.

Disconnect input speed sensor connector.

3.

Turn ignition switch ON.

4.

Check voltage between input speed sensor harness connector terminal and ground. 

Is the inspection result normal?

YES 

>> GO TO 2.

NO

>> GO TO 6.

2.

CHECK INPUT SPEED SENSOR GROUND CIRCUIT 

Check continuity between input speed sensor harness connector terminal and ground. 

Is the inspection result normal?

YES 

>> GO TO 3.

NO

>> Repair or replace malfunctioning parts.

3.

CHECK CIRCUIT BETWEEN INPUT SPEED SENSOR AND TCM (PART 1)

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector.

3.

Check continuity between input speed sensor harness connector terminal and TCM harness connector
terminal.

Is the inspection result normal?

YES 

>> GO TO 4.

NO

>> Repair or replace malfunctioning parts.

4.

CHECK CIRCUIT BETWEEN INPUT SPEED SENSOR AND TCM (PART 2)

Check continuity between input speed sensor harness connector terminal and ground. 

Engine speed

: 1,200 rpm or more

Vehicle speed

: 40 km/h (25 MPH) or more

+

−

Voltage

Input speed sensor

Connector

Terminal

F47

3

Ground

10 – 16 V

Input speed sensor

—

Continuity

Connector

Terminal

F47

1

Ground

Existed

Input speed sensor

TCM

Continuity

Connector

Terminal

Connector

Terminal

F47

2

F1

24

Existed

TM-538

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

P0717 INPUT SPEED SENSOR A

Is the inspection result normal?

YES 

>> GO TO 5.

NO

>> Repair or replace malfunctioning parts.

5.

CHECK TCM INPUT SIGNALS

1.

Connect all of disconnected connectors.

2.

Lift the vehicle.

3.

Start the engine.

4.

Check frequency of input speed sensor.

Is the inspection result normal?

YES >> Check 

intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> Replace input speed sensor. Refer to 

TM-632, "Removal and Installation"

.

6.

DETECT MALFUNCTIONING ITEMS

Check the following items:
• Open circuit or short circuit in harness between ignition switch and input speed sensor. Refer to 

PG-56, "Wir-

ing Diagram - IGNITION POWER SUPPLY -"

.

• 10A fuse [No.74, located in the fuse block (J/B]. Refer to 

PG-97, "Fuse, Connector and Terminal Arrange-

ment"

.

• IPDM E/R
Is the check result normal?

YES

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

Input speed sensor

—

Continuity

Connector

Terminal

F47

2

Ground

Not existed

+

−

Condition

Frequency

(Approx.)

TCM

Connector

Terminal

F1

24

Ground

• Shift position: “M1” position
• Vehicle speed: 20 km/h (12 MPH)

880 Hz

JSDIA3769GB