Nissan Qashqai J11. Manual - part 375

ECK-60

< SYSTEM DESCRIPTION >

[K9K]

DIAGNOSIS SYSTEM (ECM)

DMPR VLV SEN VO

mV

Inlet throttle position sensor voltage

EST INL FLP TMP

°

C or 

°

F

Inlet throttle upstream temperature

INL FLP SEN SUP VO

mV

Inlet throttle position sensor signal voltage is displayed.

EGR POSITION

%

High pressure EGR position is displayed.

TURB TMP SET

°

C or 

°

F

Exhaust gas temperature set point is displayed.

MANIFOLD PRESSURE

mbar

Intake manifold pressure computed from the TC boost sen-
sor is displayed.

EXH GAS TEMP (UPSTM CAT)

°

C or 

°

F

This item is indicated, but not used.

EXH THRTL VALVE OFFSET

%

Exhaust Air Flap - Current value of the “'last closed thrust 
position” learnt.

OIL DILUTION INFORMATION

%

Oil dilution rate

L/ PRES EGR/V FIRST OFFSET

%

Low Pressure EGR valve - Current value of the first closed 
thrust position learnt

L/PRES EGR VALVE POSITION

%

Low pressure EGR volume control valve position is dis-
played.

EXH THROTTLE POSITION

%

Exhaust throttle opening rate is displayed.

ALTERNATOR POWER

W

Alternator power

L/PRES EGR VALVE POS SEN

mV

Low pressure EGR volume control valve position sensor 
signal voltage is displayed.

ENGINE REV COUNT

—

Number of engine revolutions since the last oil drain

ENG OIL DILU RATIO

%

Current oil dilution rate for oil wear estimation

ENG TORQUE

Nm

Engine output torque calculated by ECM is displayed.

EXH THROTTLE POS SEN

mV

Exhaust throttle position sensor signal voltage is displayed.

DPF PRESSURE

hPa

Memorized difference pressure to apply on the CSF differ-
ential pressure for adaptation

Cruise control setting

km or mile

The preset ASCD vehicle speed is displayed.

DURATION OF RESUME BUT-
TON PRESS

s

Duration of resume button press is displayed.

DURATION OF + BUTTON 
PRESS

s

Duration of SET/+ button press is displayed.

DURATION OF - BUTTON 
PRESS

s

Duration of SET/- button press is displayed.

DURATION OF SUSPEND BUT-
TON PRESS

s

Duration of suspend button press is displayed.

NUMBER OF ABNORMAL CC/
SL TRANSITIONS

—

Maximum value of blocked button detection counter

MOTOR

RUNNING/
OFF/
STALLED/
CRANKING

Engine status is displayed.

1ST IN VAL OPEN PR

YES/NO

Inlet throttle valve offset - first opened learning running

1ST IN VAL CLOS PR

YES/NO

Inlet throttle valve offset - first closed learning running

THERMOPLUNGER

DETCT/AC-
TIVE

Thermoplunger No.1 status is displayed.

THERMOPLNGR 2

DETCT/AC-
TIVE

Thermoplunger No.2 status is displayed.

THERMOPLNGR 3

DETCT/AC-
TIVE

Thermoplunger No.3 status is displayed.

EGR FUN PROG

YES/NO

High pressure EGR volume control valve offset - first learn-
ing running

Monitor item

Unit

Description

Remarks

DIAGNOSIS SYSTEM (ECM)

ECK-61

< SYSTEM DESCRIPTION >

[K9K]

C

D

E

F

G

H

I

J

K

L

M

A

ECK

N

P

O

CAM TDC SYNC

NOT DONE/
DONE

Camshaft/crankshaft synchronization status is displayed.

C/U+AFTR IGN

MISSING/
PRESENT

Ignition switch status is displayed.

CLUTCH PEDAL SWITCH

INACTIVE/AC-
TIVE/
BLOCKED

Clutch pedal position switch status is displayed.

CCS LMT BTN

INACTIVE/IN-
VALID/CO.1/
SUSPD/MI-
NUS/PLUS/
RSTRT

ASCD steering switch status is displayed.
• INACTIVE: unpressed
• INVALID: invalid voltage
• CO.1: open circuit
• SUSPD: suspend switch pressed
• MINUS: SET/

−

 switch pressed

• PLUS: SET/+ switch pressed
• RSTRT: RES switch pressed

CRS CN/SPD LMT OP

OFF/SL ON/SL 
SUS/SL INHI/
CC ON/CC 
SUS/CC INHI/
NONE

ASCD and speed limiter status is displayed.
• OFF: ASCD and speed limiter is no activated.
• SL ON: speed limiter is activated. (active or over speed)
• SL SUS: speed limiter is activated. (awaiting or sus-

pended)

• SL INHI: speed limiter requested and in failure
• CC ON: ASCD is activated. (active)
• CC SUS: ASCD is activated. (awaiting or suspended)
• /CC INH: ASCD requested and in failure
• NONE: ASCD and speed limiter not present

CC/SL CONNECTION AFTER 
CC BUTTON PRESSED

Not detected/
DETCT

When ASCD MAIN switch is pressed, it displays actual 
ASCD operating condition detected by ECM.

CC/SL CONNECTION AFTER 
SL BUTTON PRESSED

Not detected/
DETCT

When speed limiter MAIN switch is pressed, it displays ac-
tual speed limiter operating condition detected by ECM.

CRS C/SPD LIM

Inactive/REG-
UL/LIMIT/Inco-
herence

Speed limiter MAIN switch status is displayed.

CC/SL ACT DR

STAT1/STAT2/
STAT3/STAT4/
STAT5

Cancellation condition of ASCD/speed limiter is displayed.
• STAT1: ASCD/speed limiter main switch changed.
• STAT2: Suspend button is pressed.
• STAT3: ASCD brake switch is ON.
• STAT4: Clutch pedal position switch is ON.
• STAT5: Shift the selector lever to “N” position.
• NONE: Deactivation

TRC/ANTI-YAW CNT

No/Yes

Anti skid regulation or anti yaw control in regulation.

CRUISE CONTROL

COR/Incoher-
ence

Speed/set point ratio too small.

PARKING BRAKE

RELES/AP-
PLIED

Parking brake status is displayed.

CC CONT INHI INJ

No/Yes

ASCD system engine control inhibition

SL INHI INJECTION

No/Yes

Speed limiter system engine control inhibition

CLUTCH INFO UNAV

Not detected/
DETCT

Clutch information unavailable is detected.

BRAKE INFO UNAVAI

Not detected/
DETCT

Brake information unavailable is detected.

BRAKE INFO ABSENT

Not detected/
DETCT

Brake information absent is detected.

DECELE W/O BRAKE

Not detected/
DETCT

Sudden braking detected without brake information

SHA DEC W/O BRAK

Not detected/
DETCT

Braking detected without brake information

Monitor item

Unit

Description

Remarks

ECK-62

< SYSTEM DESCRIPTION >

[K9K]

DIAGNOSIS SYSTEM (ECM)

CC INHI INJECTION

Not detected/
DETCT

ASCD inhibition is detected.

DISP VEHI SP UNAV

Not detected/
DETCT

Displayed vehicle speed unavailable is detected.

ACT SP INFO ABSE

Not detected/
DETCT

Real vehicle speed unavailable is detected.

DISP SP INFO ABSE

Not detected/
DETCT

Display vehicle speed absence is detected.

CHANGE SP UNIT

Not detected/
DETCT

Change of the displayed speed unit is detected.

SL INHI INJECTION

Not detected/
DETCT

Speed limiter inhibition is detected.

VEHICLE SPEED UNIT

km/h/mph

Vehicle speed is displayed.

WIRED BRAK CONTA

OFF/
PRESSED/
INTM

ASCD brake switch state is displayed.

CC OPERATING RELIABLY

STAT1/STAT2/
STAT3

State of the failures which cause irreversible ASCD safety 
failure is displayed.
• STAT1: Presence of ASCD force request despite the 

ASCD deactivation

• STAT2: Activation of the open brake switch without 

ASCD deactivation

• STAT3: Activation of the minimum travel clutch switch 

without ASCD deactivation

TURBO REGULATION

Inactive/REG-
UL/INTM/DIAG 
MODE/
PRTCT/MAX

Boost regulation state is displayed.

CC/SL CONN AUTH

Inactive/AC-
TIVE

Authorization to connect ASCD and speed limiter options 
status is displayed.

LOW FUEL LEVEL INFORMA-
TION

OK/Low

LOW FUEL LEVEL INFORMATION is displayed.

WTR DIESEL DETECTR

Not detected/
DETCT

This item is not used.

COOLING FAN ACTIV REQ

INACTIVE/AC-

TIVE

Cooling fan request status is displayed.

CC/SL SPEED SIGNAL MONI-
TORING

STAT1/STAT2/
STAT3/STAT4/

STAT5/STAT6

State of the reversible failures not due to ASCD/speed lim-
iter which cause ASCD/speed limiter failure
• STAT1: Real vehicle speed unavailable is detected.
• STAT2: Displayed vehicle speed unavailable is detected.
• STAT3: Real vehicle speed absence is detected.
• STAT4: Display vehicle speed absence is detected.
• STAT5: Change of the displayed speed unit is detected.
• STAT6: Speed limiter inhibition is detected.

COMBU MODE SET

NORMAL/
1.DEF/2.DEF/
3.DEF/STAT4/
RESERV/
STAT5/STAT6/
4.DEF

REQUIREMENT VALUE OF COMBUSTION MODE isdis-
played.

COMBUSTION MODE

NORMAL/
2.DEF/3.DEF/
STAT4/RE-
SERVED/
1.DEF/STAT5/
STAT6/4.DEF

REQUIREMENT VALUE OF COMBUSTION MODE isdis-
played.

Monitor item

Unit

Description

Remarks

DIAGNOSIS SYSTEM (ECM)

ECK-63

< SYSTEM DESCRIPTION >

[K9K]

C

D

E

F

G

H

I

J

K

L

M

A

ECK

N

P

O

EXH THRTL/ V CLSD POS LRN

NOT DONE/

DONE

Indicates Exhaust Throttle Valve Closed Position Learning 
status.

ETAT PRIVE 5

1.DEF/2.DEF

Combustion mode - particulate filter regeneration authori-
zation state

INJ ERROR FIND PROCEDRE

1.DEF/2.DEF

Error detected by the monitoring of supplier injections (val-
ue after reset)

L/PRES EGR/V CLSD POS LRN

NOT DONE/

DONE

Indicates Low Pressure EGR Volume Control Valve Closed 
Position Learning status.

LOW PRESSURE EGR VALVE 
PROGRAMMING

UNAVAIL-

ABLE/AVAILBL

Low Pressure EGR Volume Control Valve Offset - first 
learning running

STARTER BUTTON

PRESSED/
RELSD

Ignition switch status is displayed.

ENGAGE REVERSE GEAR

No/Yes

Selector lever “R” position status is displayed.

AUTOMATIC GEARBOX IN DE-
FECT MODE

Not detected/
DETCT

Transaxle in limp home mode is detected.

ACT SP INFO UNAV

Not detected/
DETCT

Real vehicle speed unavailable is detected.

VEHICLE SPEED DISPLAYED

UNAVAIL-
ABLE/AVAILBL

Displayed vehicle speed received on the CAN network not 
available after a filtering time

VEHICLE SPEED MULTI-
PLEXED INFORMATION

UNAVAIL-
ABLE/AVAILBL

Vehicle speed received on the CAN network not available 
after a filtering time

GEARBOX RATIO

DECLTC/1/2/3/
4/5/6/RVRS

Current gear engaged
• DECLTC: Declutched at rest
• 1: 1st gear
• 2: 2nd gear
• 3: 3rd gear
• 4: 4th gear
• 5: 5th gear
• 6: 6th gear
• RVRS: Reverse

FIRST START

NOT DONE/
DONE

First start status is displayed.

CLUTCH CONTACT MULTI-
PLEX SIGNAL

UNAVAIL-
ABLE/AVAILBL

Filtered unavailable clutch pedal status information

CLUTCH CONTACT WIRING - 
START OF TRAVEL

UNAVAIL-
ABLE/AVAILBL

Begin stroke clutch pedal switch for cruise control safety

COMP + AFTER IGNITION

PRESENT/IN-
ACTIVE

Key state

A/C ATHRSTION

NOT DONE/
DONE/INAC-
TIVE

Air conditioning request

THERMOPLUNGER1 RELAY

DEACTIVAT/
ACTIVE/INAC-
TIVE

Thermoplungers command state

THERMOPLUNGER2 RELAY

DEACTIVAT/
ACTIVE/INAC-
TIVE

Thermoplungers command state

THERMOPLUNGER3 RELAY

DEACTIVAT/
ACTIVE/INAC-
TIVE

Thermoplungers command state

BRAKE PEDAL

NO PRS/RE-
SERVED/
PRESSED/IN-
ACTIVE

Brake pedal - close active switch state

Monitor item

Unit

Description

Remarks