Nissan Qashqai J11. Manual - part 343

P2100, P2103 THROTTLE CONTROL MOTOR RELAY

ECM-349

< DTC/CIRCUIT DIAGNOSIS >

[MR20DD]

C

D

E

F

G

H

I

J

K

L

M

A

ECM

N

P

O

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair or replace malfunctioning part.

ECM-350

< DTC/CIRCUIT DIAGNOSIS >

[MR20DD]

P2101 ELECTRIC THROTTLE CONTROL FUNCTION

P2101 ELECTRIC THROTTLE CONTROL FUNCTION

DTC Description

INFOID:0000000010703039

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Crankshaft position sensor (POS)
- Throttle control motor circuit is open or shorted.
- Throttle control motor relay circuit is open or shorted.
• Electric throttle control actuator

FAIL-SAFE

DTC CONFIRMATION PROCEDURE

1.

CHECK DTC PRIORITY

If DTC P2101 is displayed with DTC P2100 or P2119, first perform the trouble diagnosis for DTC P2100 or
P2119.

Is applicable DTC detected?

YES

>> Perform diagnosis of applicable. Refer to 

ECM-93, "DTC Index"

.

NO

>> GO TO 2.

2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1.

Turn ignition switch OFF and wait at least 10 seconds.

2.

Turn ignition switch ON.

3.

Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.

>> GO TO 3.

3.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON and wait at least 2 seconds.

2.

Start engine and let it idle for 5 seconds.

3.

Check DTC.

Is DTC detected?

YES

>> Proceed to 

ECM-350, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010703040

1.

CHECK DTC PRIORITY

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detecting condition

P2101

ETC FNCTN/CIRC-B1
(Throttle actuator “A” control motor circuit 
range/performance)

Electric throttle control function does not operate properly.

Engine operating condition in fail-safe mode

Fail safe mode

Vehicle behavior

Others

ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed 
opening (approx. 5 degrees) by the return spring.

P2101 ELECTRIC THROTTLE CONTROL FUNCTION

ECM-351

< DTC/CIRCUIT DIAGNOSIS >

[MR20DD]

C

D

E

F

G

H

I

J

K

L

M

A

ECM

N

P

O

If DTC P2101 is displayed with DTC P2100 or P2119, first perform the trouble diagnosis for DTC P2100 or
P2119.
Is applicable DTC detected?

YES

>> Perform diagnosis of applicable. Refer to 

ECM-93, "DTC Index"

.

NO

>> GO TO 2.

2.

CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL

Check the voltage between ECM harness connector terminals as per the following conditions.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 3.

3.

CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect ECM harness connector.

3.

Disconnect IPDM E/R harness connector.

4.

Check the continuity between ECM harness connector and IPDM E/R harness connector.

5.

Also check harness for short to ground and to power.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace malfunctioning part.

4.

CHECK THROTTLE CONTROL MOTOR RELAY POWER SUPPLY CIRCUIT

1.

Check the continuity between ECM harness connector and IPDM E/R harness connector.

2.

Also check harness for short to ground and to power.

Is the inspection result normal?

YES

>> Perform the trouble diagnosis for power supply circuit.

NO

>> Repair or replace malfunctioning part.

5.

CHECK THROTTLE CONTROL MOTOR OUTPUT SIGNAL CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect electric throttle control actuator harness connector.

3.

Disconnect ECM harness connector.

4.

Check the continuity between electric throttle control actuator harness connector and ECM harness con-
nector.

+

−

Condition

Voltage

(Approx.)

ECM

Connector

Terminal

Connector

Terminal

F16

80

E57

128

Ignition switch

OFF

0 V

ON

Battery voltage

+

−

Continuity

ECM

IPDM E/R

Connector

Terminal

Connector

Terminal

F16

80

F90

97

Existed

+

−

Continuity

ECM

IPDM E/R

Connector

Terminal

Connector

Terminal

F16

65

F90

102

Existed

ECM-352

< DTC/CIRCUIT DIAGNOSIS >

[MR20DD]

P2101 ELECTRIC THROTTLE CONTROL FUNCTION

5.

Also check harness for short to ground and to power.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace malfunctioning part.

6.

CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY

1.

Remove the intake air duct. Refer to 

EM-147, "Removal and Installation"

.

2.

Check if foreign matter is caught between the throttle valve and the housing.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Remove the foreign matter and clean the electric throttle control actuator inside, then perform

throttle valve closed position learning. Refer to 

ECM-128, "Work Procedure"

.

7.

CHECK THROTTLE CONTROL MOTOR

Check the throttle control motor. Refer to 

ECM-352, "Component Inspection"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace electric throttle control actuator. Refer to 

EM-149, "Removal and Installation"

.

Component Inspection

INFOID:0000000010703041

1.

CHECK THROTTLE CONTROL MOTOR

1.

Turn ignition switch OFF.

2.

Disconnect electric throttle control actuator harness connector.

3.

Check the resistance between electric throttle control actuator terminals as per the following.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace electric throttle control actuator. Refer to 

EM-149, "Removal and Installation"

.

+

−

Continuity

Electric throttle control actu-

ator

ECM

Connector

Terminal

Connector

Terminal

F45

5

F16

69

Not existed

73

Existed

6

69

Existed

73

Not existed

Electric throttle control actuator

Resistance

(Approx.)

+

−

Terminal

5

6

1 - 15 

Ω

 [at 25

°

C (77

°

F)]